Instruction Manual for VEVOR models including: EV-ACS1601U, K3, EV-ACS1601U K3 Level 1 2 Portable Electric Vehicle Charger, EV-ACS1601U K3, Level 1 2 Portable Electric Vehicle Charger, Portable Electric Vehicle Charger, Electric Vehicle Charger, Vehicle Charger, Charger
File Info : application/pdf, 8 Pages, 6.81MB
DocumentDocumentLEVEL 1/2 PORTABLE ELECTRIC VEHICLE CHARGER MODEL: EV-ACS1601U/K3 MODEL: EV-ACS1601U/K3 LEVEL 1/2 PORTABLE ELECTRIC VEHICLE CHARGER This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product. Warning-To reduce the risk of injury, user must read instructions manual carefully. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and. (2) this device must accept any interference received, including interference that may cause undesired operation. INSTRUCTIONS WARNINGS Do not connect the EV charger into a power outlet that is not properly grounded. Please use the EV charger only within the specified operating parameters. The charger is designed only for vehicles that are compatible with the SAE J1772 AC Level 1/2 charging standard. Do not use the EV charger if it is defective, appears cracked, frayed, broken or otherwise damaged, or fails to operate. Do not use the EV charger's plug or adapter in any outlet for which they are not designed. Do not attempt to open, disassemble, repair, tamper with, or modify the EV charger. The EV charger is not user-serviceable. Do not disconnect the EV charger from the wall outlet when the vehicle is charging. Do not use the EV charger when either you, the vehicle or the EV charger is exposed to severe rain, snow, electrical storm or other inclement weather. Protect the EV charger from moisture, water and foreign objects at all times. If any exist or appear to have corroded or damaged the EV charger, do not use the EV charger. Do not plug the EV charger into an electrical outlet that is submerged in water or covered in snow. If in this situation, the EV charger is already plugged in and needs to be unplugged, turn off the breaker before unplugging the EV charger. Do not touch the EV charger's end terminals with sharp metallic objects, such as wire, tools or needles. Do not forcefully fold any part of the EV charger or damage it with sharp objects. Do not insert foreign objects into any part of the EV charger. The EV charger is not a toy and should be kept away from children. If the EV charger is operating, children nearby should be supervised at all times. PRODUCT SPECIFICATIONS Voltage Current Power Plug Input / Output Circuit Breaker Requirements Standard Operating Temperature Storage Temperature IP Rating Total Length 110-240V AC Single-phase 16A Max 3.84 kW Max 6-20 Plug + 5-15 Adapter 240V/AC 16A 120V/AC 12A 20A Circuit Breaker for 6-20 Plug 15A Circuit Breaker for 5-15 Adapter SAE J1772 (IEC 62196 Type 1) -22°F to 122°F ( -30°C to 50°C ) -40°F to 185°F ( -40°C to 85°C ) IP66 25 Feet PRODUCT OVERVIEW NEMA 6-20 Plug Control Box LED Light Charging Cable SAE J1772 Connector Protective Cap CAUTIONS BEFORE START CHARGING 1. Make sure that the power outlet is properly grounded before plug the EV charger into it. 2. Do not use the EV charger if it is defective, appears cracked, frayed, broken or otherwise damaged, or fails to operate. Do not start using if the plug is dirty or wet. 3. The plug should be inserted completely into the power outlet. HOW TO START CHARGING 1. Turn off the vehicle and completely insert the EV charger's plug into the power outlet. 2. Take off the protective cap. 3. Plug the charger connector into your vehicle and start charging. HOW TO STOP CHARGING 1. Unlock the vehicle and press the button above the handle to pull the charger connector out of the charge port. 2. Disconnect the charger's plug from the power outlet. 3. Put on the protective cap then put the charger into the storage bag, and store it in an appropriate location. LED LIGHT STATUS DESCRIPTION Color Status Description Color Status Description Flashing Charging Flashing EV Connected Solid on Fully charged Solid on Ground fault Solid on Standing by Flashing Ground fault TROUBLESHOOTING Diagnostic Problem The red light is solid on Leakage Over voltage Over current Solution 1.Check whether the charger is broken or damaged. 2.Re-plug the charger. 3.Try a different outlet. lf the error persists, please contact our support service. The red light is flashing The power outlet is not properly grounded. The charger must be plugged into a power outlet that is properly grounded, though the charging is allowed when connected to the vehicle. The blue light is flashing, but the charging is not in progress. The blue light is solid on but the charging is not in progress. Something stops the charging progress. Re-plug the charger connector and it will start charging again. The charger is not connected to the vehicle. Make sure that the charger connector is plugged completely into the charge port. The charging speed is not fast as advertised, or the charging current can't reach the maximum ampere. A. The charger or the vehicle is overheating. B. The vehicle charging setting is set a limited ampere. A. Stop the charging progress, wait for the charger or vehicle cooling down and start charging again. B. Cancel the ampere limited setting in your vehicle. Sanven Technology Ltd. Address: Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730