Catron AI AC Powered Switch Interface

For Push Button, Toggle, and Rotary Switches

Lumos Controls

[CCC] [CE] [Wi-Fi] [Bluetooth] [Zigbee]

Installation and Quick Start Sheet

WARNING AND GUIDELINES!!!

Read and follow all safety instructions!!

DO NOT INSTALL DAMAGED PRODUCT!

This product has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.

WARNING: TURN THE POWER OFF AT THE CIRCUIT BREAKER BEFORE WIRING

WARNING: Risk of Product Damage

Electrostatic Discharge (ESD): ESD can damage product(s). Personal grounding equipment should be worn during all installation or servicing of the unit.
Do not stretch or use cable sets that are too short or are of insufficient length.
Do not modify the product.
Do not mount near gas or electric heater.
Do not change or alter internal wiring or installation circuitry.
Do not use product for anything other than its intended use.

WARNING - Risk of Electric Shock

Verify that supply voltage is correct by comparing it with the product information.
Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements.
All wiring connections should be capped with UL approved recognized wire connectors.
All unused wiring must be capped.

Installation Best Practices

Do's

Installation should be performed by a qualified electrician.
Installation shall be in accordance with all applicable local and NEC codes.
Turn the power OFF at circuit breakers before wiring.
Observe the correct polarity of output terminal.

Don'ts

Don't use outdoors.
Avoid input voltage exceeding maximum rating.
Don't disassemble the products.

Product Overview

Catron AI is an AC powered wireless switch interface device. This interface device shall be connected with 4 toggle switches or push button switches and a rotary switch for the control of light devices, groups, or scenes and animations. It is part of Lumos Controls ecosystem which includes controllers, sensors, switches, modules, drivers, gateways, and analytical dashboards.

Image description: The Catron AI AC Powered Switch Interface, a compact white device with connection terminals and branding.

INSTALLATION INSTRUCTIONS

Wiring instructions

Turn off the power before wiring.
Place the device on the flush box and tighten it using the screw. *(Depth of the box to be decided based on the size of switch)*
To power the device, connect the AC Line and Neutral wires from the mains supply to the Line and Neutral of the device respectively.
Based on the number of toggle/push button switches to control, connect the input lines to the switches.
Connect 0-10V input wires to the rotary switch to control the dimming (optional).
Cover the switch.

Diagram description: Installation steps are illustrated: 01 shows turning off power, 02 shows placing the device in a flush box, 03 shows connecting AC Line and Neutral wires, 04 shows connecting switch input wires, and 05 shows connecting optional 0-10V input wires.

Specifications

Parameter	Min	Type	Max	Unit	Remarks
Input Voltage	90		277	VAC	Rated Input voltage
Input Current			10	mA	@ 230V
Power Consumption			2	W	Active Power
Input Frequency	50		60	Hz
Frequency Range	2400		2483	MHz
Inrush Current			4	A
Surge Transient Protection			4	kV	@Line to Line: Bi-Wave
Stand By Consumption			9	mA
Switch Input Voltage		3.3	V	Applicable for toggle/ push-button switches
Dimmer Input Voltage		0	10	V	Applicable for slider/ rotary dimmer switches
Dimming Range		0	100	%
Tx Power			8	dBm
Rx Sensitivity		-92		dBm	Conductive
Ambient Temperature	-20		50	°C
Relative Humidity		20	85	%
Dimensions (LxWxH)		43 x 35 x 20		mm
Dimensions (LxWxH)		1.7 x 1.4 x 0.8		in

Required Tools & Supplies

Screwdriver

Wiring Diagram

The wiring diagram shows the Catron AI device connected to a power source (Line and Neutral). It details connections to four toggle or push-button switches labeled T1, T2, T3, and T4 via individual switch input wires (yellow, red, green, blue respectively). Additionally, it shows a 0-10V input connection and a Common Ground connection, typically for a rotary dimmer switch.

Application

An image depicts the Catron AI device installed within a wall box, connected to a bank of four white toggle switches in a modern office or living space, illustrating its integration into a smart home environment.

Troubleshooting

Issue: Lights go back to ON state after a Power Outage.

This is normal operation. The device has a fail-safe feature that forces it to 50% or 100% output, or 0-10V at full output, upon loss of power. Alternatively, the device will return to its previous state after power is restored, as configured using the Lumos Controls mobile app.

Issue: Device doesn't operate immediately after power ON.

Check whether you have set up a transition time.

Issue: Lights flickering.

The connection is not appropriate.
The wires are not secured firmly with connectors.

Issue: Lights did not turn ON.

Circuit breaker tripped.
Fuse has blown.
Inappropriate wiring.

Commissioning

Once powered up, the device is ready for commissioning via the Lumos Controls mobile app (available on iOS and Android). To begin, click the '+' icon from the 'Devices' tab. The app allows preset configurations to be loaded after the device is added. These 'Commissioning Settings' are sent to the devices. Once commissioned, the device appears in the 'Devices' tab for individual operations like ON/OFF/dimming.

Please visit the Help center for more details.

Warranty

5-year limited warranty. Please find warranty terms and conditions. Note: Specifications may change without notice. Actual performance can vary due to end-user environment and application.