PICOS 4.5 Release Notes

These release notes summarize new features, hardware support, known bugs, and bug fixes for PICOS 4.5. It is recommended to read all content before upgrading.

PICOS 4.5.0E (ESS)

An Early Sales Support (ESS) stable version for specific customer deployments and early adoption scenarios, providing early access to new features.

PICOS 4.5.1E (Evaluation)

An evaluation release for the N8550-24CD8D platform, focusing on core features with some advanced capabilities not yet fully implemented.

PICOS 4.5.0M (GA)

A General Availability (GA) release with enhanced stability and performance improvements, supporting all platforms except FS S3410/S3270 series switches.

PICOS 4.5.2E (ESS)

An ESS version for the new platform N9600-64OD.

Hardware Support

4.5.2E: Support for FS Model N9600-64OD
4.5.1E: Support for FS Model N8550-24CD8D

New Features

Layer 2 and Layer 3

IPv6 ND Inspection: Security feature to protect IPv6 networks by managing and validating Neighbor Discovery Protocol (NDP) messages.
IPv6 ND Snooping: Security feature to safeguard IPv6 networks against attacks, similar to ARP Snooping in IPv4.
MPLS: Multiprotocol Label Switching operating between link and network layers for IP connectivity services.
PIM BSR (Bootstrap Router): Dynamic RP for PIM devices, enabling election of an RP through aggregation of C-RP information.
Ingress Buffer: Supports ingress buffer management, including guaranteed, shared, and headroom management.
PFC Watchdog Manual Control: Detects and resolves PFC deadlocks with automatic and manual recovery options.
PFC Deadlock Prevention: Modifies DSCP and Dot1p priority to prevent PFC deadlock states.
Easy ECN: Enables WRED policies and threshold configuration for effective network congestion management.
DLB (Dynamic Load Balance): Introduces dynamic and intelligent load balancing by incorporating timestamp and real-time load measurements.
Standby IP Address: Defaults to 192.168.1.1 for management if DHCP fails and no static IP is set, ensuring management access.
Perpetual PoE: Allows Power Sourcing Equipment (PSE) to continue providing power during system restarts and upgrades.
PFC/ECN: GRPC monitoring of PFC pause frame counts, PFC deadlock, and ECN-marked packet counts.

Feature Enhancement

DHCP Server Enhancement: Resolved issue with clients unable to obtain addresses in DHCP relay scenarios.
DHCP ZTP: Configurable address pools for IP addresses and network information for clients.
400G Port Splitting: Support for splitting 400G ports into 2x200G or 4x100G on N9550-32D/AS9716-32D switches.
PBR ECMP: Policy-Based Routing action supports next-hop-group for ECMP routing.

L2L3 WEB

L2L3 WEB Access Control: Support for enabling/disabling Layer 2 and Layer 3 WEB access via the set system services web disable command.

Fixed Issues

MLAG: Resolved issues with link state showing IDLE, CONNECTING status after peer restart, and failure to reach FULL state.
Port LED: Fixed issue where port LEDs remained off in breakout mode on N9550-32D.
CLI Output: Resolved issue with no output for run show interface gigabit-ethernet on AS9716-32D.
System Crash: Fixed system crash when handling large files on AS4610/N3024/N3048.
CPU/Memory Leak: Resolved high CPU usage and memory leak due to FPM packet handling on S5850-48S6Q.
ACL/VRRP: Fixed incorrect VRRP virtual MAC installation in ACLs.
VLAN Removal: Resolved issue where kernel incorrectly deleted VLANs during native VLAN removal.
Serial Number: Fixed issue with incorrect reading of the power module serial number on N8550-32C.
MAC Learning: Resolved MAC learning issue exceeding 8K entries in MLAG scenarios on N9550-32D.
DOT1X: Fixed crash during 802.1X reauthentication with specific session timeout configurations.
SNMP: Resolved issue with SNMP failing to retrieve LLDP neighbor details when exceeding five neighbors.
LLDP/SNMP Notification: Resolved issue where LLDP might not notify SNMP after interface reconfiguration.
DHCP Server: Fixed address assignment failure with excessive address pools.

Known Limitations

N9600-64OD: Sub-interfaces may not come up in 8x50G mode with OSFP-SR8-800G module.
N9600-64OD: Port light remains illuminated after module removal in port splitting mode.
N9600-64OD: Undersized packets not counted in 'Undersize Packets' statistics.
N9600-64OD: BMC light remains red after successful startup; PICOS does not control BMC light.
N9600-64OD: Front Panel Ports 65 and 66 are not supported.
N9600-64OD: Packets smaller than 295 bytes may not reach full line rate due to hardware limitations.
N9600-64OD: Software-based MAC address learning results in a slower learning rate.
PICOS 4.5.0M: Does not support OSPF Multi-Instance.
PICOS 4.5.0M: Does not support telnet server.

PICOS Routing and Switching Command Reference

This section provides commands for command-line interface operations, system management, NAC configuration, SNMP, Mirroring, RMON, RESTCONF, Interface configuration, VLANs, Voice VLANs, Layer 3 Routing, BGP, OSPF, Static Routes, Route Maps, BFD, Policy-Based Routing, IP Source Guard, ND Inspection, ND Snooping, IS-IS, ACLs, QoS, CoPP, Buffer Management, Rate Limiting, Traffic Policers, PFC, Protocol Configuration (ARP, LACP, sFlow, DHCP, LLDP), IP Multicast, IGMP, PIM, MSDP, MVR, OpenFlow, VXLAN, OVSDB, BGP EVPN, PoE, VRRP, Spanning Tree Protocol, MLAG, GRE Tunnels, GVRP, MVRP, ERPS, EFM OAM, MPLS, and Loopback Detection.

Command-Line Interface Commands

copy running-config startup-config: Saves the running configuration to flash.
set cli idle-timeout : Sets the maximum idle time before session termination.
set cli screen-length : Sets the number of lines displayed before pausing.
set cli terminal {ansi | linux | vt100 | xterm}: Specifies the terminal type.
syslog monitor : Enables or disables the syslog monitor function.
syslog notify : Enables or disables multi-window command configuration display.
hwclock [function] [option...]: Administration tool for hardware clock time.
rollback <0 | 1 | 2 | 3 | 4 | 5 | default>: Rolls back the configuration to a previous state.

System Management Commands

NAC Configuration Commands

set protocols dot1x aaa radius authentication server-ip [shared-key ]: Configures RADIUS authentication server IP and shared key.
set protocols dot1x aaa radius authentication server-ip priority : Configures the priority of the RADIUS authentication server.
set protocols dot1x aaa radius authentication server-ip retry-num : Configures the maximum number of authentication attempts.
set protocols dot1x aaa radius authentication server-ip retry-interval : Configures the interval for re-sending authentication messages.
set protocols dot1x aaa radius authentication server-ip detect-interval : Configures the detection interval for the RADIUS server.
set protocols dot1x interface auth-mode {802.1x | mac-radius | web}: Sets the authentication mode for an interface.
set protocols dot1x interface auth-mode 802.1x fallback-to-web disable {true | false}: Enables or disables fallback to WEB function for 802.1X.
set protocols dot1x interface authentication-open disable {true | false}: Enables or disables open authentication function.
set protocols dot1x aaa radius dynamic-author client [shared-key ]: Configures the IP address and shared key of the RADIUS DAC for CoA.
set protocols dot1x aaa radius nas-ip : Configures the NAS IP address for RADIUS access-request messages.
set protocols dot1x aaa radius accounting disable {true | false}: Enables or disables user accounting function.
set protocols dot1x interface host-mode {single | multiple}: Configures the host access mode on an interface.
set protocols dot1x block-vlan-id : Configures the block VLAN ID.
set protocols dot1x server-fail-vlan-id : Configures the server fail VLAN ID.
set protocols dot1x filter sequence from destination-address-ipv4 : Configures destination IPv4 address for NAC ACL rules.
set protocols dot1x filter sequence from destination-address-ipv6 : Configures destination IPv6 address for NAC ACL rules.
set protocols dot1x filter sequence from destination-port : Configures destination port for NAC ACL rules.
set protocols dot1x filter sequence from ether-type : Configures Ethernet type for NAC ACL rules.
set protocols dot1x filter sequence from source-address-ipv4 : Configures source IPv4 address for NAC ACL rules.
set protocols dot1x filter sequence from source-address-ipv6 : Configures source IPv6 address for NAC ACL rules.
set protocols dot1x filter sequence from source-port : Configures source port for NAC ACL rules.
set protocols dot1x filter sequence from protocol {icmp | igmp | ip | ospf | others | udp | tcp}: Configures protocol type for NAC ACL rules.
set protocols dot1x filter sequence then action {discard | forward}: Configures the action for matching ACL rules.
run show dot1x all: Displays global NAC information.
run show dot1x interface [gigabit-ethernet ]: Displays NAC configuration and port status for interfaces.
run show dot1x server: Displays RADIUS server information.
run show dot1x dynamic filter: Displays dynamic filter information.
run show dot1x downloadable filter: Displays downloadable filter information.
run show dot1x interface statistics gigabit-ethernet: Displays statistics for gigabit-ethernet interfaces.
set protocols dot1x server-fail recovery-method: Configures the recovery method for server failure.
set protocols dot1x aaa radius authentication server-ip consecutive-detect-num: Configures consecutive detection number for RADIUS server.
set protocols dot1x aaa vrf mgmt-vrf: Configures management VRF for AAA RADIUS.
set protocols dot1x interface session-timeout: Configures session timeout for an interface.
set protocols dot1x interface recovery-timeout: Configures recovery timeout for an interface.
set protocols dot1x server-fail recovery-timeout: Configures recovery timeout for server failure.
set protocols dot1x interface max-sessions: Configures maximum sessions for an interface.
set protocols dot1x max-sessions-per-port: Configures maximum sessions per port.
set protocols dot1x aaa radius authentication server-ip auth-port: Configures authentication port for RADIUS server.
set protocols dot1x aaa radius authentication server-ip acct-port: Configures accounting port for RADIUS server.
set protocols dot1x aaa radius dynamic-author client port: Configures port for RADIUS DAC.
run show dot1x radius-port: Displays RADIUS port information.
set protocols dot1x filter sequence from destination-mac-address: Configures destination MAC address for NAC ACL rules.
set protocols dot1x filter sequence from vlan: Configures VLAN for NAC ACL rules.

SNMP Configuration Commands

set protocols snmp trap-group targets security-name: Configures SNMP trap group targets.
set protocols lldp snmp-trap: Enables SNMP traps for LLDP.
set protocols snmp trap-group event cpu-threshold {enable | high | interval | low}: Configures SNMP trap group CPU threshold events.
set protocols snmp trap-group event mac-threshold {enable | interval | limit}: Configures SNMP trap group MAC threshold events.
set protocols snmp trap-group vrf mgmt-vrf: Configures management VRF for SNMP trap group.
set protocols snmp trap-group version: Configures SNMP trap group version.
set protocols snmp v3 {enable | usm-user | usm-user group | group notify-view | group read-view | group write-view | group security-level | usm-user authentication-mode | usm-user authentication-key | usm-user privacy-mode | usm-user privacy-key}: Configures SNMPv3 parameters.
set protocols snmp v3 mib-view subtree {mask | type}: Configures SNMPv3 MIB view subtree.
set protocols snmp trap-group source-interface: Configures source interface for SNMP traps.
set protocols snmp community {community | authorization | clients}: Configures SNMP community settings.
set protocols snmp contact: Configures SNMP contact information.
set protocols snmp location: Configures SNMP location information.
run show snmp statistics: Displays SNMP statistics.

Mirror Configuration Commands

set interface ethernet-switching-options analyzer {input | output}: Configures analyzer input or output.
set interface ethernet-switching-options analyzer erspan {input | output source-ip | output dest-ip | output vrf}: Configures ERSPAN analyzer settings.
run show analyzer: Displays analyzer information.
set firewall filter sequence then erspan {source-ip | dest-ip | vrf | ttl}: Configures ERSPAN settings within firewall filters.

RMON Commands

run show rmon {alarms | eventlog | events | history | statistics}: Displays RMON information.
set protocols snmp rmon alarm {falling-event-index | falling-threshold | interval | owner | rising-event-index | rising-threshold | sample-type | variable}: Configures RMON alarm parameters.
set protocols snmp rmon event {community | description | owner | type}: Configures RMON event parameters.
set protocols snmp rmon history {buckets | interface | interval | owner}: Configures RMON history parameters.
set protocols snmp rmon statistics {interface | owner}: Configures RMON statistics parameters.

RESTCONF Commands

set protocols restconf {port | traceoptions flag config disable | traceoptions flag all disable | traceoptions flag datastore disable}: Configures RESTCONF settings.
run show system {boot-messages | connections | core-dumps | cpu-usage | date | fan | memory-usage | name | ntp-status | os | processes brief | processes detail | rollback compare to | rollback file | rollback list | rpsu | serial-number | temperature | uptime | users}: Displays system information.

System Management Commands (Continued)

AAA Configuration

set system aaa {local disable | radius accounting disable | radius accounting server-ip | radius accounting server-ip port | radius accounting server-ip shared-key | radius accounting server-ip timeout | radius authorization disable | radius authorization server-ip | radius authorization server-ip port | radius authorization server-ip shared-key | radius authorization server-ip timeout | radius vrf mgmt-vrf | tacacs-plus accounting | tacacs-plus authorization | tacacs-plus auth-type | tacacs-plus disable | tacacs-plus key | tacacs-plus port-number | tacacs-plus timeout | tacacs-plus server-ip | tacacs-plus source-interface | local-auth-fallback disable | tacacs-plus vrf mgmt-vrf}: Configures AAA services.

Hostname and Time

set system hostname: Sets the system hostname.
set system timezone: Sets the system timezone.

NTP Configuration

set system ntp {server-ip | source-interface | vrf mgmt-vrf}: Configures NTP settings.

Interface Configuration

set interface gigabit-ethernet ptp mode: Configures PTP mode for Gigabit Ethernet interfaces.

SSH Configuration

set system services ssh {connection-limit | disable | protocol-version v2 | rate-limit | root-login | idle-timeout | port}: Configures SSH service settings.

SNMP ACL

set system snmp-acl security-name network: Configures SNMP ACL.

Syslog Configuration

set system syslog {server-ip | local-file | vrf mgmt-vrf}: Configures syslog settings.

USB Configuration

set system usb disable: Disables USB functionality.

Management Ethernet Configuration

set system management-ethernet eth0 {ip-address {IPv4 | IPv6} | ip-gateway {IPv4 | IPv6}}: Configures management Ethernet interface IP settings.
show system management-ethernet: Displays management Ethernet interface information.

System Operations

run request system reboot: Reboots the system.
run show system hwinfo: Displays hardware information.
ping: Pings a host.
traceroute: Traces the route to a host.
tftp: TFTP client operations.
set protocols sflow collector vrf mgmt-vrf: Configures sFlow collector VRF.
scp: SCP client operations.
set system login banner: Sets the system login banner.
upgrade2 image-file {backup-file | factory-default | use-prev-config}: Manages system image upgrades.
set system dns-server-ip: Configures DNS server IP addresses.
set system console idle-timeout: Configures console idle timeout.
set system login {multiline-banner message | multiline-announcement message}: Configures login banners and announcements.
set system aaa radius source-interface: Configures source interface for AAA RADIUS.
set protocols grpc {enable | port}: Configures gRPC settings.
set system ztp enable: Enables Zero Touch Provisioning (ZTP).
telnet: Telnet client operations.
set system start-shell-sh password: Sets the password for start-shell-sh.
set system services {telnet disable | web disable}: Disables telnet or web services.

Interface Configuration Commands

Port Security Commands

set interface gigabit-ethernet port-security {mac-address vlan | mac-limit | sticky | violation | block}: Configures port security settings.
set interface ethernet-switching-options port-error-discard timeout: Configures port error discard timeout.
run show port-security {brief | address | interface}: Displays port security information.
run clear port-security {port-error | sticky interface | sticky address | dynamic interface | dynamic address}: Clears port security statistics.

L3 Interface

set l3-interface vlan-interface {vrf | address prefix-length | rate-limit | mtu | dhcp}: Configures L3 VLAN interface settings.
set l3-interface loopback {address | disable | vrf}: Configures L3 loopback interface settings.
run show l3-interface {vlan-interface | | loopback}: Displays L3 interface information.
run clear l3-interface statistics: Clears L3 interface statistics.
set l3-interface routed-interface {dhcp | rate-limit | mtu | vrf | address | description}: Configures L3 routed interface settings.
set l3-interface vlan-interface pmtu-discovery: Configures PMTU discovery for L3 VLAN interfaces.
set l3-interface routed-interface pmtu-discovery: Configures PMTU discovery for L3 routed interfaces.

Routed Interface

run show interface routed-interface brief: Displays brief routed interface information.
run show vlans routed-vlan: Displays routed VLAN information.
set interface aggregate-ethernet routed-interface {enable | name | sub-interface vlan-id}: Configures routed aggregate Ethernet interfaces.
set interface gigabit-ethernet routed-interface {enable | sub-interface}: Configures routed Gigabit Ethernet interfaces.
set vlans reserved-vlan: Configures reserved VLANs.
set interface gigabit-ethernet routed-interface name: Configures the name for routed Gigabit Ethernet interfaces.
set interface gigabit-ethernet speed: Configures the speed for Gigabit Ethernet interfaces.

Uplink Failure Detection Commands

run show interface ufd: Displays Uplink Failure Detection (UFD) information.
set interface ufd link-to-{monitor | disable}: Configures UFD links.

IPv6 Neighbor Discovery Protocol Command Reference

set l3-interface routed-interface ipv6-nd {adv-interval-option | home-agent-config-flag | home-agent-lifetime | home-agent-preference | managed-config-flag | mtu | other-config-flag | prefix off-link | prefix preferred-lifetime | prefix router-address | prefix valid-lifetime | ra-fast-retrans | ra-interval | ra-lifetime | reachable-time | router-preference | suppress-ra}: Configures IPv6 ND parameters for routed interfaces.
set l3-interface vlan-interface ipv6-nd {adv-interval-option | home-agent-config-flag | home-agent-lifetime | home-agent-preference | managed-config-flag | mtu | other-config-flag | prefix off-link | prefix preferred-lifetime | prefix router-address | prefix valid-lifetime | ra-fast-retrans | ra-interval | ra-lifetime | reachable-time | router-preference | suppress-ra}: Configures IPv6 ND parameters for VLAN interfaces.

Interface Management

set management-ethernet-speed eth0: Configures management Ethernet speed.
set interface gigabit-ethernet up-mode: Configures Gigabit Ethernet up-mode.
show interface bpdu-tunneling: Displays BPDU tunneling information.
show interface aggregate-ethernet [dot1q-tunneling]: Displays aggregate Ethernet interface information.
show interface {brief | detail | diagnostics optics all | ecmp max-path | flexlink}: Displays various interface statistics and configurations.
show interface gigabit-ethernet : Displays detailed Gigabit Ethernet interface information.
set interface gigabit-ethernet {fec | family ethernet-switching vlan members | family ethernet-switching port-mode | family ethernet-switching bpdu-tunneling protocol | ether-options 802.3ad | duplex auto | breakout-type | auto-speeds}: Configures Gigabit Ethernet interface features.
set interface ecmp hash-mapping field {vlan | port-source | port-destination | ip-source | ip-protocol | ip-destination | ingress-interface} disable: Disables ECMP hash mapping fields.
set interface bpdu-tunneling destination-mac: Configures BPDU tunneling destination MAC.
set interface aggregate-ethernet {family ethernet-switching vlan members | family ethernet-switching port-mode | disable | description | aggregated-ether-options lacp fallback timeout | aggregated-ether-options lacp fallback enable | aggregated-ether-options lacp}: Configures aggregate Ethernet interface features.
run show interface port-index-mapping: Displays interface port index mapping.
run show interface diagnostics tdr: Displays TDR diagnostics for interfaces.
interface max-route-limit: Configures maximum route limit per interface.
interface max-acl-rule-limit {egress/ingress}: Configures maximum ACL rule limit per interface.
interface gigabit-ethernet wred queue {min_thresh | max_thresh | enable | ecn_thresh | drop_probability}: Configures WRED for Gigabit Ethernet ports.
interface gigabit-ethernet storm-control {mode} {ratio | pps | kbps}: Configures storm control for Gigabit Ethernet ports.
interface gigabit-ethernet static-ethernet-switching mac-address vlan : Configures static MAC address for Ethernet switching.
interface gigabit-ethernet snmp-trap: Enables SNMP traps for Gigabit Ethernet ports.
interface gigabit-ethernet power-preemphasis-level: Configures power pre-emphasis level.
interface gigabit-ethernet mtu: Configures MTU for Gigabit Ethernet ports.
interface gigabit-ethernet mac-learning {boolean}: Configures MAC learning for Gigabit Ethernet ports.
interface gigabit-ethernet link-fault-signaling {ignore-remote-fault | ignore-local-fault} {boolean}: Configures link fault signaling.
interface gigabit-ethernet family ethernet-switching vlan members untagged: Configures untagged VLAN members.
interface gigabit-ethernet family ethernet-switching native-vlan-id: Configures native VLAN ID.
interface gigabit-ethernet family ethernet-switching dot1q-tunneling {mode | ingress | ether-type | egress}: Configures dot1q tunneling.
interface gigabit-ethernet disable: Disables a Gigabit Ethernet port.
interface gigabit-ethernet ether-options flow-control: Configures flow control for Gigabit Ethernet ports.
interface gigabit-ethernet description: Configures description for Gigabit Ethernet ports.
interface gigabit-ethernet crossflow {local-control | enable}: Configures crossflow for Gigabit Ethernet ports.
interface gigabit-ethernet backup-port {mode | interface | delay}: Configures backup port settings.
interface ethernet-switching-options {mac-table-aging-time | buffer queue-limit}: Configures Ethernet switching options.
interface ecmp max-path: Configures maximum ECMP paths.
interface cut-through-mode: Configures cut-through mode.
interface aggregate-ethernet storm-control {mode} pps: Configures storm control for aggregate Ethernet.
interface aggregate-ethernet static-ethernet-switching mac-address vlan: Configures static MAC address for aggregate Ethernet.
interface aggregate-ethernet snmp-trap: Enables SNMP traps for aggregate Ethernet.
interface aggregate-ethernet mtu: Configures MTU for aggregate Ethernet.
interface aggregate-ethernet hash-mapping mode: Configures hash mapping mode for aggregate Ethernet.
interface aggregate-ethernet family ethernet-switching {native-vlan-id | dot1q-tunneling mode | dot1q-tunneling ingress | dot1q-tunneling ether-type | dot1q-tunneling egress}: Configures aggregate Ethernet family settings.
interface aggregate-ethernet crossflow {local-control | enable}: Configures crossflow for aggregate Ethernet.
interface aggregate-ethernet backup-port {mode | interface | delay}: Configures backup port settings for aggregate Ethernet.
interface aggregate-ethernet aggregated-ether-options {min-selected-port | flow-control}: Configures aggregate Ethernet options.
interface aggregate-balancing hash-mapping field {vlan | port-source | port-destination | ip-source | ip-protocol | ip-destination | ingress-interface | ethernet-type | ethernet-source-address | ethernet-destination-address} disable: Disables aggregate balancing hash mapping fields.
set interface ecmp hash-mapping {randomized-load-balancing | round-robin-load-balancing | resilient-load-balancing | dlb-normal | symmetric | dlb-optimal | dlb-assigned}: Configures ECMP hash mapping load balancing.
set interface gigabit-ethernet {breakout | cdr}: Configures breakout and CDR for Gigabit Ethernet.

VLAN Configuration Commands

set vlans dot1q-tunneling {egress from | egress then action | egress then service-vlan | ingress from double-tag service-vlan | ingress from one-tag customer-vlan-list | ingress from untag enabled | ingress then}: Configures dot1q tunneling for VLANs.
set vlans vlan-id {description | l3-interface | vlan-name | private-vlan mode | private-vlan association}: Configures VLAN ID settings.
set mac-map mac-address vlan: Maps MAC addresses to VLANs.
run show vlans [private-vlan [type]]: Displays VLAN information.
run show mac-map: Displays MAC map information.
set tracemac disable: Disables tracemac.
tracemac: Traces MAC addresses.

Voice VLAN Configuration Commands

set interface gigabit-ethernet voice-vlan {mode | tagged mode | vlan-id}: Configures voice VLAN for Gigabit Ethernet interfaces.
set vlans voice-vlan {aging | dscp | local-priority | mac-address mask | mac-address description}: Configures voice VLAN settings.
show vlans voice-vlan [oui | vlan-id ]: Displays voice VLAN information.

Layer 3 Routing Commands

run show {neighbors | route [forward-host | forward-route] | vrf}: Displays Layer 3 routing information.
set ip {vrf | routing enable}: Configures IP routing.
set system management-vrf enable: Enables management VRF.

BGP Commands

run show bgp [neighbor | route | unicast neighbor graceful-restart]: Displays BGP information.
set protocols bgp {aggregate-address | always-compare-med | bestpath as-path type multipath-relax | bestpath bandwidth | bestpath compare-routerid | bestpath med missing-as-worst | cluster-id | graceful-shutdown | listen | local-as | max-med | multipath maximum-paths}: Configures BGP parameters.
set protocols bgp neighbor {activate | addpath-tx-all-paths | addpath-tx-bestpath-per-as | advertisement-interval | allowas-in | as-override | capability extended-nexthop | default-originate | description | disable-connected-check | ebgp-multihop | filter-list | next-hop-self | password | peer-group | prefix-list | remote-as | remove-private-as | route-map | route-reflector-client | send-community | shutdown | soft-reconfiguration | timers connect | timers holdtime | timers keepalive | ttl-security hops | update-source | timers delayopen | maximum-prefix | maximum-prefix-out | port | sender-as-path-loop-detection}: Configures BGP neighbor parameters.
set protocols bgp {network | network-import-check | peer-group | redistribute | route-map delay-timer | router-id | table-map | timers | update-delay | ebgp-requires-policy | fast-external-failover | confederation identifier | confederation peers | dampening | default local-preference | as-notation | neighbor local-as}: Configures general BGP settings.

OSPFv2 Commands

run clear ospf interface: Clears OSPF interface.
run show ospf {border-routers | database | interface | neighbor | route | summary-address}: Displays OSPFv2 information.
set protocols ospf {aggregation timer | area area-type | area filter-list prefix | area no-summary | area range | area virtual-link | area virtual-link authentication | area virtual-link authentication-key | area virtual-link dead-interval | area virtual-link hello-interval | area virtual-link message-digest-key md5 | area virtual-link retransmit-interval | area virtual-link transmit-delay | auto-cost reference-bandwidth | compatible rfc1583 | default-information originate | default-metric | interface area | interface authentication address | interface authentication message-digest | interface cost | interface dead-interval | interface hello-interval | interface message-digest-key md5 | interface network | interface priority | interface retransmit-interval | interface transmit-delay | log-adjacency-changes | max-metric router-lsa administrative | max-metric router-lsa on-shutdown | max-metric router-lsa on-startup | multi-instance disable | network area | passive-interface | redistribute | redistribute metric-type | redistribute route-map | router-id | summary-address | timers lsa min-arrival | timers throttle spf | traceoption ism | traceoption lsa | traceoption nsm | traceoption packet | traceoption zebra | graceful-restart enable | capability opaque | graceful-restart grace-period | graceful-restart helper enable | graceful-restart helper planned-only | graceful-restart helper strict-lsa-checking | graceful-restart helper supported-grace-time}: Configures OSPFv2 parameters.
run graceful-restart prepare ospf: Prepares for OSPF graceful restart.
run show ospf graceful-restart helper: Displays OSPF graceful restart helper status.
set protocols ospf interface authentication-key: Sets authentication key for OSPF interface.

OSPFv3 Command Reference

set protocols ospf6 {area | area range | area stub | area stub no-summary | auto-cost reference-bandwidth | distance | distance-ospf6 | interface area | interface cost | interface dead-interval | interface hello-interval | interface ifmtu | interface mtu-ignore | interface network | interface passive | interface priority | interface retransmit-interval | interface transmit-delay | log-adjacency-changes | redistribute | router-id | stub-router administrative | timers lsa min-arrival | timers throttle spf | traceoption | traceoption border-routers | traceoption lsa | traceoption message | traceoption neighbor | traceoption route | traceoption spf | traceoption zebra | graceful-restart enable | capability opaque | graceful-restart grace-period | graceful-restart helper enable | graceful-restart helper planned-only | graceful-restart helper lsa-checking-disable | graceful-restart helper supported-grace-time}: Configures OSPFv3 parameters.
run graceful-restart prepare ospf6: Prepares for OSPFv3 graceful restart.
run show ospf6 graceful-restart helper: Displays OSPFv3 graceful restart helper status.

Static Route Configuration Commands

set protocols static {interface-route interface | mroute | route}: Configures static routes.

Route Map Commands

run show routing route-map: Displays route map information.
set routing {as-path-list | large-community-list expanded | large-community-list standard | prefix-list | prefix-list description | community-list expanded | community-list standard | extcommunity-list expanded | extcommunity-list standard}: Configures routing lists.
set routing route-map {set-action large-community | call | description | match as-path | match community | match community-with-exact-match | match evpn default-route | match evpn route-type | match evpn vni | match extcommunity | matching-policy | match interface | match ipv4-addr address | match ipv4-addr next-hop | match ipv4-addr route-source | match ipv6-addr | match large-community | match local-preference | match metric | match origin | match peer | match source-protocol | match source-vrf | match tag | on-match}: Configures route map match conditions.
set routing route-map set-action {aggregator | as-path exclude | as-path prepend | atomic-aggregate | comm-list-delete | community | community-additive | extcommunity | extcommunity bandwidth | extcommunity bandwidth-non-transitive | ip-next-hop | ipv4-vpn-next-hop | ipv6-next-hop | label-index | large-comm-list-delete | local-preference | metric | metric-type | origin | originator-id | src | tag | weight}: Configures route map set actions.

Route Leaking Commands

BGP Route Leaking Commands

set protocols bgp {ipv4-unicast import vrf | ipv6-unicast import vrf | ipv6-unicast import vrf-route-map | vrf ipv4-unicast import vrf | vrf ipv4-unicast import vrf-route-map | vrf ipv6-unicast import vrf}: Configures BGP route leaking.

Static Route Leaking Commands

set protocols static route nexthop-vrf next-hop: Configures static route next-hop VRF.
set protocols static vrf route nexthop-vrf next-hop: Configures static VRF route next-hop VRF.

BFD Configuration Commands

run show bfd { | counters | peers}: Displays BFD information.
set protocols bfd {multihop peer local-address detect-multiplier minimum-ttl passive-mode receive-interval shutdown transmit-interval | peer detect-multiplier echo-mode echo receive-interval echo transmit-interval local-address minimum-ttl passive-mode receive-interval shutdown transmit-interval | profile detect-multiplier echo-mode echo receive-interval echo transmit-interval minimum-ttl passive-mode receive-interval shutdown transmit-interval}: Configures BFD parameters.
set protocols {bgp bfd | ospf6 interface bfd | ospf interface bfd | pim interface bfd}: Enables BFD for routing protocols.

Policy-Based Routing (PBR) Commands

set routing pbr map sequence {match destination-ipv4 | match source-ipv4 | match destination-port | match source-port | match destination-ipv6 | match source-ipv6 | action nexthop | action dscp | action nexthop-group}: Configures PBR map sequences.
set routing nexthop-group nexthop-vrf nexthop: Configures next-hop VRF in next-hop group.
set routing pbr map vlan-interface: Configures PBR map for VLAN interfaces.
run show pbr map: Displays PBR map information.
run clear pbr map: Clears PBR map information.

IPv4 Source Guard (IPSG for IPv4) Commands

set ip-source-guard {binding ip | enable | verify | traceoptions enable}: Configures IPv4 Source Guard.
run show ip-source-guard binding: Displays IPv4 Source Guard binding information.

IPv6 Source Guard (IPSG for IPv6) Commands

set ipv6-source-guard {binding ip | enable | verify | traceoptions enable}: Configures IPv6 Source Guard.
run show ipv6-source-guard binding: Displays IPv6 Source Guard binding information.

ND Inspection Commands

set protocols neighbour inspection {vlan disable | validate source-mac | trust-port}: Configures ND inspection.
run show nd inspection dhcp6-snooping binding: Displays ND inspection DHCPv6 snooping binding.

ND Snooping Commands

set protocols neighbour snooping {vlan enable | trust-port}: Configures ND snooping.
set neighbour snooping max-user-number: Configures maximum user number for ND snooping.
set protocols neighbour snooping static-prefix vlan: Configures static prefix VLAN for ND snooping.
run show neighbor snooping [prefix | binding]: Displays ND snooping information.
run clear neighbor snooping {prefix | binding}: Clears ND snooping information.

IS-IS Commands

set protocols isis area-tag {network-entity | is-type | interface | hostname-dynamic | area-password authentication-type | area-password authentication-key | area-password authenticate-snp | domain-password authentication-type | domain-password authentication-key | domain-password authenticate-snp | attached-bit receive-ignore | attached-bit send | log-adjacency-changes | metric-style | set-overload-bit | purge-originator | lsp-mtu | lsp-timers gen-interval | lsp-timers refresh-interval | lsp-timers max-lifetime | spf-interval | spf-delay-ietf init-delay | spf-delay-ietf short-delay | spf-delay-ietf long-delay | spf-delay-ietf holddown | spf-delay-ietf time-to-learn | default-information originate | default-information originate metric | default-information originate route-map | topology ipv6-unicast}: Configures IS-IS area tags.
set protocols isis area-tag interface {circuit-type | csnp-interval | psnp-interval | hello-padding | hello-interval | hello-multiplier | metric | network point-to-point | passive | password authentication-type | password authentication-key | priority | three-way-handshake | bfd | topology ipv6-unicast}: Configures IS-IS interface settings.
set protocols isis {area-tag redistribute | traceoption events | traceoption adj-packets | traceoption route-events | traceoption snp-packets}: Configures IS-IS redistribution and trace options.
run show isis {summary | interface | database | hostname | neighbor | route | topology}: Displays IS-IS information.

ACL Configuration Commands

set firewall filter {description | input interface | time-range periodic start | time-range periodic end}: Configures firewall filter descriptions and time ranges.
run show timerange: Displays time range information.
run show filter: Displays firewall filter information.
set firewall filter sequence {then dscp | then action | from destination-port | from protocol ip | from protocol ospf | description | output interface | input vlan-interface | from protocol udp | destination-address-ipv6 | then forwarding-class | from protocol tcp flags | from protocol igmp | output routed-interface | log interval | from source-port | output vlan-interface | from destination-address-ipv4 | system-output disable | from ip trust-mode | from source-mac-address | from destination-mac-address | from protocol tcp | from ip value | input routed-interface | from protocol icmp | from protocol others | from ether-type | from vlan | from source-address-ipv6 | from source-address-ipv4}: Configures firewall filter sequences.

QoS Configuration Commands

set class-of-service {forwarding-class local-priority | scheduler mode | interface default-priority | classifier forwarding-class code-point | interface classifier | classifier | classifier forwarding-class | classifier trust-mode | scheduler guaranteed-rate | scheduler-profile forwarding-class scheduler | scheduler weight | easy-ecn mode | interface scheduler-profile | scheduler max-rate}: Configures QoS settings.
run show class-of-service interface: Displays QoS interface information.

CoPP Commands

set class-of-service scheduler {max-bandwidth-pps | min-bandwidth-pps}: Configures CoPP scheduler bandwidth.
set class-of-service scheduler-profile copp-profile forwarding-classs scheduler: Configures CoPP scheduler profile.
set class-of-service scheduler weight (CoPP): Configures CoPP scheduler weight.
set firewall filter copp sequence {from destination-address-ipv4 | from destination-address-ipv6 | from destination-mac-address | from destination-port | from ether-type | from protocol | from source-address-ipv4 | from source-address-ipv6 | from source-mac-address | from source-port | from vlan | then forwarding-class | then dscp}: Configures CoPP firewall filters.
run show copp {bandwidth | statistics}: Displays CoPP information.
run show interface stm: Displays interface STM information.
run clear copp statistics: Clears CoPP statistics.
set class-of-service forwarding-class local-priority (CoPP): Configures CoPP local priority.
run show filter copp: Displays CoPP filter information.

Buffer Management Commands

set interface ethernet-switching-options buffer egress-queue {shared-ratio | mc-queue-dynamic-shared}: Configures egress buffer queue settings.
run show interface egress-buffer: Displays egress buffer information.
run show interface gigabit-ethernet egress-queues: Displays Gigabit Ethernet egress queues.

Interface-based Rate Limiting Commands

set interface gigabit-ethernet rate-limiting {ingress kilobits | ingress ratio | ingress burst | egress kilobits | egress ratio | egress burst}: Configures interface rate limiting.

ACL-based Traffic Policer Commands

set firewall policer if-exceeding {count-mode | rate-limit | burst-limit}: Configures ACL-based traffic policer.
set firewall filter sequence then policer: Applies policer to firewall filter sequence.
set firewall policer if-exceeding action discard: Discards traffic exceeding policer limits.
run show policer: Displays policer information.

PFC Commands

set class-of-service pfc-profile {code-point drop}: Configures PFC profile code point drop.
set class-of-service interface pfc-profile: Configures PFC profile for interfaces.
set interface gigabit-ethernet ethernet-switching-options buffer ingress-queue {guaranteed | shared-ratio | threshold | reset-offset}: Configures ingress buffer queue for PFC.
set interface ethernet-switching-options buffer service-pool threshold: Configures service pool threshold.
set interface gigabit-ethernet ethernet-switching-options buffer ingress-queue headroom: Configures ingress buffer headroom.
set interface gigabit-ethernet ethernet-switching-options buffer egress-queue {shared-ratio | threshold}: Configures egress buffer queue for PFC.
set class-of-service pfc-watchdog {granularity | restore-action | code-point detect-interval | code-point restore-interval | interface pfc-watchdog code-point enable | threshold period | threshold count | interface pfc-watchdog restore-mode}: Configures PFC watchdog.
run clear class-of-service interface pfc-watchdog {auto | manual}: Clears PFC watchdog.
run show pfc-watchdog {stats | config}: Displays PFC watchdog information.
run show interface gigabit-ethernet {ingress-buffer | egress-buffer}: Displays interface buffer information.
set class-of-service interface pfc-uplink-group {original-dscp to-code-point | original-dscp dscp}: Configures PFC uplink group.

Protocol Configuration Commands

ARP

set protocols arp {interface address mac-address | interface proxy | inspection vlan disable | inspection access-list ip mac-address | inspection vlan access-list | inspection trust-port}: Configures ARP settings.
run show arp inspection {dhcp-binding | interface | vlan | access-list | statistics vlan}: Displays ARP inspection information.
set protocols arp aging-time: Configures ARP aging time.

LACP

set protocols lacp interface priority: Configures LACP interface priority.
set protocols lacp priority: Configures LACP priority.

sFlow

set protocols sflow {agent-id | collector udp-port | disable}: Configures sFlow settings.
set protocols sflow interface {polling-interval | header-len | header-len | sampling-rate egress | disable | sampling-rate ingress}: Configures sFlow interface settings.
set protocols sflow {polling-interval | sampling-rate egress | sampling-rate ingress | source-address}: Configures sFlow global settings.

DHCP Snooping

set protocols dhcp snooping {vlan | trust-port | vlan option82-policy | option82 circuit-id | option82 remote-id | option82 trust-all | binding file | binding write-delay}: Configures DHCP snooping.
run show dhcp snooping binding: Displays DHCP snooping binding information.

DHCP Relay

set protocols dhcp relay interface {disable | dhcp-server-address | relay-agent-address | option82-policy}: Configures DHCP relay interface settings.
set protocols dhcp relay option82 {circuit-id | remote-id | trust-all}: Configures DHCP relay option 82 settings.

DHCP Server

set protocols dhcp server pool {network | range low | range high | domain-name | dns-server | default-router | lease-time | vrf | tftp-server | log-server | bootfile-name}: Configures DHCP server pools.
run show dhcp server binding {address | interface}: Displays DHCP server binding information.
set protocols dhcp server interface disable: Disables DHCP server on an interface.

DHCPv6 Relay

set protocols dhcp6 relay interface {disable | destination | remote-id}: Configures DHCPv6 relay interface settings.
run show dhcp6 relay-stats: Displays DHCPv6 relay statistics.

DHCPv6 Snooping

set protocols dhcp6 snooping {vlan | trust-port | binding file | binding write-delay | vlan option-policy | option37 remote-id | option18 interface-id | interface max-clients}: Configures DHCPv6 snooping.
run show dhcp6 snooping binding: Displays DHCPv6 snooping binding information.

DHCPv6 Guard

set protocols dhcp6 guard policy {device-role | trust-port | interface | preference-min | preference-max | match server source-address | match reply ia-prefix}: Configures DHCPv6 guard policy.
run show dhcp6 guard policy: Displays DHCPv6 guard policy information.
run show dhcp6 guard: Displays DHCPv6 guard information.

LLDP

run show lldp neighbor: Displays LLDP neighbor information.

ARP

run show arp: Displays ARP information.

sFlow Interface

set protocols sflow interface {polling-interval | header-len | header-len | sampling-rate egress | disable | sampling-rate ingress}: Configures sFlow interface settings.

IP Multicast Commands

IGMP Snooping Configuration Commands

run show igmp-snooping [groups | mrouter | querier]: Displays IGMP snooping information.
set protocols igmp-snooping {enable | interface max-groups | last-member-query-count | last-member-query-interval | max-response-time | query-interval | report-suppression | robustness-variable | vlan-id enable | vlan-id fast-leave | vlan-id mrouter interface | vlan-id querier address | vlan-id querier enable | vlan-id querier other-querier-timer | vlan-id querier version | vlan-id static group interface | vlan-id unregistered flood-all}: Configures IGMP snooping.

IGMP Commands

set protocols igmp interface {join-group | query-interval | query-max-response-time | version}: Configures IGMP interface settings.
run show igmp groups: Displays IGMP groups.
run show igmp interface: Displays IGMP interface information.

PIM Configuration Commands

set protocols pim {ecmp | interface active-active | interface drpriority | interface hello holdtime | interface hello interval | interface sm | interface use-source | join-prune-interval | keep-alive-timer | packets | register-suppress-time | rp | spt-switchover infinity-and-beyond | ssm prefix-list | interface bsm | interface unicast-bsm}: Configures PIM settings.
run show pim {interface | rp-info | neighbor | upstream | mroute mtrace | group-type | bsr | bsm-database | bsrp-info}: Displays PIM information.
run clear pim bsr-data: Clears PIM BSR data.

Multicast Source Discovery Protocol (MSDP) Commands

set protocols msdp mesh-group {source | member}: Configures MSDP mesh groups.
run show msdp {mesh-group | peer | sa}: Displays MSDP information.

Multicast VLAN Registration (MVR) Commands

run show igmp-snooping mvr {mvlan | receiver-vlan}: Displays MVR information.
set protocols igmp-snooping vlan-id mvr {receiver vlan-list | source group}: Configures MVR for VLANs.

OpenFlow Commands in CrossFlow Mode

VXLAN Commands

set vxlans source-interface address: Configures VXLAN source interface address.

OVSDB VTEP Command

set protocols ovsdb controller {vrf mgmt-vrf | address | inactivity-probe-duration | maximum-backoff-duration | port | protocol | interface | management-ip | ssl bootstrap | ssl ca-cert | ssl certificate | ssl private-key}: Configures OVSDB controller settings.
set vxlans {l3-vni prefix-routes-only | vni mcast-group}: Configures VXLAN settings.
run show vxlan {statistics | vni | address-table | arp | l3-vni entry | neighbor}: Displays VXLAN information.
set vxlans vni {decapsulation mode | encapsulation mode | encapsulation vlan | flood vtep | flood vtep mac-address | flood vtep traffic-type | vlan}: Configures VXLAN VNI settings.
set vxlans tunnel-mac-leaning disable: Disables tunnel MAC learning.
set vxlans l3-vni: Configures L3 VNI for VXLAN.

BGP EVPN Commands

run show bgp evpn {summary | import-rt | vrf-import-rt | vni}: Displays BGP EVPN summary information.
run show evpn {es | access-vlan | arp-cache | next-hops | rmac | mac vni}: Displays EVPN information.
set interface aggregate-ethernet evpn mh {es-df-pref | es-id | es-sys-mac}: Configures EVPN MH for aggregate Ethernet.
set l3-interface {routed-interface router-mac | vlan-interface anycast address | vlan-interface anycast mac | vlan-interface router-mac}: Configures EVPN router MAC and anycast addresses.
set protocols bgp evpn {advertise-default-gw | advertise ipv4-unicast | advertise ipv6-unicast | advertise-svi-ip | default-originate | disable-ead-evi-rx | disable-ead-evi-tx | vni | vni advertise-default-gw | vni advertise-svi-ip | vni rd | vni route-target type}: Configures BGP EVPN advertisement.
set protocols bgp neighbor evpn {activate | allowas-in | route-map | route-reflector-client}: Configures BGP EVPN neighbor settings.
set protocols bgp vrf evpn advertise-pip ip: Configures BGP EVPN advertise-pip IP.
set protocols evpn mh {mac-holdtime | redirect-off | startup-delay}: Configures EVPN MH parameters.
set vxlans vni arp-nd-suppress disable: Disables ARP/ND suppress for VXLAN VNI.
set protocols bgp evpn advertise-all-vni: Advertises all VNIs in BGP EVPN.
set protocols evpn mh neigh-holdtime: Configures EVPN MH neighbor holdtime.
run show bgp evpn route [detail | vni | rd | type]: Displays BGP EVPN route information.

PoE Configuration Commands

set poe interface {max-power | detection-type | enable | mode | priority | threshold-mode | lldp-negotiation}: Configures PoE interface settings.
set poe power {management-mode | mode | voltage}: Configures PoE power settings.
set poe traceoptions flag all disable: Disables PoE trace options.
run show poe interface: Displays PoE interface information.
run show poe power: Displays PoE power information.
set poe perpetual-power enable: Enables perpetual PoE.

VRRP Commands

set protocols vrrp interface vrid {disable | version | ip | priority | interval | preempt enable | load-balance disable | load-balance virtual-mac time-interval | accept disable | authentication type | simple-key | md5-key}: Configures VRRP interface settings.
run show vrrp: Displays VRRP information.
set protocols vrrp interface vrid ipv6-nd {adv-interval-option | home-agent-config-flag | home-agent-lifetime | home-agent-preference | managed-config-flag | mtu | other-config-flag | prefix off-link | prefix valid-lifetime | prefix preferred-lifetime | prefix router-address | ra-fast-retrans | ra-interval | ra-lifetime | reachable-time | router-preference | suppress-ra}: Configures VRRP IPv6 ND parameters.

Spanning Tree Protocol Commands

run show spanning-tree [mstp | pvst | rstp | statistics | stp]: Displays Spanning Tree Protocol information.
set protocols spanning-tree {enable | force-version | interface enable}: Enables Spanning Tree Protocol.
set protocols spanning-tree mstp {bridge-priority | configuration-name | forward-delay | hello-time | interface bpdu-filter | interface bpdu-guard | interface edge | interface external-path-cost | interface internal-path-cost | interface manual-forwarding | interface mode | interface port-priority | interface root-guard | interface tcn-guard | max-age | max-hops | msti bridge-priority | msti interface cost | msti interface port-priority | revision-level | msti vlan}: Configures MSTP settings.
set protocols spanning-tree pvst {interface bpdu-guard | interface manual-forwarding | interface mode | interface root-guard | vlan bridge-priority | vlan enable | vlan forward-delay | vlan hello-time | vlan interface path-cost | vlan interface port-priority | vlan max-age}: Configures PVST settings.
set protocols spanning-tree rstp {bridge-priority | forward-delay | hello-time | interface bpdu-filter | interface bpdu-guard | interface edge | interface mode | interface path-cost | interface port-priority | interface root-guard | interface tcn-guard | max-age}: Configures RSTP settings.
set protocols spanning-tree stp {bridge-priority | forward-delay | hello-time | interface bpdu-filter | interface bpdu-guard | interface edge | interface mode | interface path-cost | interface port-priority | interface root-guard | interface tcn-guard | max-age}: Configures STP settings.

MLAG Commands

set protocols mlag domain { | node | interface link | peer-ip peer-link | peer-ip peer-vlan}: Configures MLAG domain settings.
run show mlag {domain | link | consistency-parameter}: Displays MLAG information.

GRE Tunnel Interface Commands

run show l3-interface tunnel: Displays GRE tunnel interface information.
set l3-interface tunnel {address | destination | disable | source | tunnel-mode gre-ip | vrf}: Configures GRE tunnel interface settings.

GVRP Commands

set protocols gvrp {join-timer | leave-timer | leaveall-timer}: Configures GVRP timers.
run clear gvrp interface statistics: Clears GVRP interface statistics.
run show gvrp interface [statistics]: Displays GVRP interface information.
set protocols gvrp {edge-switch | enable | interface enable | traceoptions flag config | traceoptions flag packets}: Configures GVRP settings.

MVRP Commands

run clear mvrp interface statistics: Clears MVRP interface statistics.
run show mvrp interface [statistics]: Displays MVRP interface information.
set protocols mvrp {edge-switch | enable | interface enable | traceoptions flag config | traceoptions flag packets | join-timer | leave-timer | leaveall-timer}: Configures MVRP settings.

ERPS Commands

run show erps {brief | interface | ring | statistics}: Displays ERPS information.
set protocols erps {ring | version | enable}: Enables ERPS.
set protocols erps ring instance {control-vlan | description | enable | guard-timer | holdoff-timer | protected-instance | r-aps level | rpl | wtr-timer | non-revertive | connect ring erps switch force | instance erps switch manual | instance erps clear ring ring instance}: Configures ERPS ring instances.
set protocols erps ring {port0 interface | port1 interface | r-aps ring-mac | sub-ring | virtual-channel}: Configures ERPS ring ports and channels.
set protocols erps tcn-propagation: Configures ERPS TCN propagation.
set protocols erps traceoptions flag {all disable | config disable | ring disable}: Disables ERPS trace options.

EFM OAM Commands

set protocols ethernet-oam interface {enable | mode | remote-loopback supported | remote-loopback timeout | ethernet-oam remote-loopback start|stop interface | timeout}: Configures EFM OAM interface settings.
set protocols ethernet-oam traceoptions flag {packets | config}: Configures EFM OAM trace options.
run show ethernet-oam [statistics]: Displays EFM OAM information.

MPLS Commands

set protocols mpls {interface | ldp router-id | ldp ordered-control | ldp neighbor password | ldp neighbor session-holdtime | ldp neighbor ttl-security disable | ldp neighbor ttl-security hops | interface | ldp ttl-security disable (IP family) | ldp label-local-advertise | ldp label-local-allocate | ldp discovery transport-address | ldp discovery hello-interval | ldp discovery hello-holdtime | ldp discovery targeted-hello-interval | ldp discovery targeted-hello-holdtime | ldp discovery targeted-hello-accept | ldp dual-stack transport-connection prefer-ipv4 | ldp dual-stack interop | ldp targeted-neighbor | ldp traceoption labels | ldp traceoption errors | ldp traceoption event | ldp traceoption discovery | ldp traceoption messages}: Configures MPLS and LDP settings.
run show mpls {ldp binding | ldp neighbor | ldp interface | forward-table | egress interface | table | interface | status | label | ldp discovery | fec}: Displays MPLS information.

Loopback Detection Commands

set protocols loopback-detection {enable | interface enable | message-interval | traceoptions configuration disable | traceoptions all disable}: Configures loopback detection.
run show loopback-detection: Displays loopback detection information.
run clear loopback-detection interface: Clears loopback detection interface information.

	FSOS IPv6 Security Command Line Reference A comprehensive command-line reference for FSOS IPv6 security features, detailing commands for DHCPv6 snooping configuration, management, and troubleshooting.
	FS S8050-20Q4C 40G IP Storage Switch Datasheet Datasheet for the FS S8050-20Q4C, a high-performance Ethernet switch designed for next-generation Metro, Data Center, and Enterprise network requirements. Features include L2/L3 capabilities, comprehensive protocols, and flexible software options for rapid service deployment and management.
	S3400-48T4SP Switch ERPS Configuration Guide This guide details the configuration of the Enhanced Ring Protection Switching (ERPS) protocol on the S3400-48T4SP Switch, focusing on ring network topology, node roles, port configurations, and protection mechanisms for fast Ethernet ring protection.
	FS SMB Office Network Solution Deployment Manual A comprehensive guide detailing the deployment of an SMB office network solution, covering typical scenarios, scheme design, product lists, data planning, and configuration steps for switches and AC controllers. It focuses on establishing a robust wireless and wired network infrastructure for small to medium-sized businesses.
	FSOS VPN Command Line Reference Guide A comprehensive guide to the FSOS VPN command-line interface, detailing commands for VRF configuration, routing, and network diagnostics.
	S3410C-16TF PicOS® Switch Hardware Guide Comprehensive hardware guide for the FS.COM S3410C-16TF PicOS® Switch, detailing installation, configuration, and operational specifications. Learn about its Broadcom BCM56150 chip, 16x 1Gb RJ45 and 2x 1Gb SFP ports, MLAG, and AmpCon-Campus management platform.
	AmpCon-Campus Management Platform User Manual V2.2.0 This user manual provides comprehensive information on the AmpCon-Campus Management Platform V2.2.0, covering its features, deployment, and management capabilities for campus networks. It details Zero Touch Provisioning, full-stack network design, switch lifecycle management, telemetry monitoring, and Ansible integration for automating network tasks.
	FS.COM AmpCon-Campus User Manual V2.2.0 - Network Management Platform Comprehensive user manual for the FS.COM AmpCon-Campus Management Platform, version 2.2.0. It details features for automated campus network deployment, management, monitoring, and automation using ZTP and Ansible.