Instruction Manual for MONSTERTECH models including: Winwing Mip Rail Mount, Mip Rail Mount, Rail Mount, Mount
Manuals – MTSIM – MONSTERTECH USA
mtsim winwing mip rail mount manual 4 profile cap assembly 35 8 25 8 m8x35 m8x25 bolt dimensions and how to measure them [mm] 35 8 25 8 m8x35 m8x25 extension
File Info : application/pdf, 36 Pages, 3.91MB
DocumentDocumentWINWING MIP RAIL MOUNT Instruction Manual Bedienungsanleitung Mode d`emploi GENERAL ASSEMBLY INFO AND HOW TO PROFILE NUT HEX KEY SET WITH BALL HEAD + EXTENSION OR SIMILAR REQUIRED MTSIM WINWING MIP RAIL MOUNT MANUAL 2 UNIVERSAL CONNECTOR slot nut M8 universal connector M8x30 ALTERNATIVE universal connector M8x30 very loose pre-assembled slide in MTSIM WINWING MIP RAIL MOUNT MANUAL 3 extension for better tightening force BOLT DIMENSIONS AND HOW TO MEASURE THEM [mm] 35 35 25 25 M8x35 M8x35 M8x25 M8x25 8 8 8 8 PROFILE CAP ASSEMBLY MTSIM WINWING MIP RAIL MOUNT MANUAL 4 PARTS 1x [dimensions in mm / different scales] No extra or spare parts listed! 40 40 40 40 465 40 1x 270 1x 140 80 3x 100 80 10x 80 4 0 40 4 0 40 80 1x 70 75 80 1x 50 55 80 2x 40 MTSIM WINWING MIP RAIL MOUNT MANUAL 5 3x 4x BAG 1 4x 4x M8 BAG 2 12x 18 22x M8 8 black 5 BAG 3 18x 22 16x M5 Ø 8 4x 30 10x 16 8 black 12x black 8,4 16 18x 5,3 10 MTSIM WINWING MIP RAIL MOUNT MANUAL 6 Slider 1x BAG 4 2x 6 4x 20 black 2x Ø32 M6 2x M6 4x M6 2 0 BAG 5 ICE MAN setup 2x 4x Ø5,5 15 5 5 2x 16 2x 20 MTSIM WINWING MIP RAIL MOUNT MANUAL 7 ASSEMBLY 3x (2x for ICE MAN setup) Also observe the Winwing operating instructions! 4x 1x 4x M5x22 washer Ø10 not for ICE MAN setup 6x washer Ø10 6x M5x22 MTSIM WINWING MIP RAIL MOUNT MANUAL 8 UFC unit assembly for ICE MAN setup 2x bracket 2x washer Ø15 2x M5x16 MTSIM WINWING MIP RAIL MOUNT MANUAL 9 counter sunk holes slot nut M6 flat nuts M6 sliders M6 x 20 flat head black knobs MTSIM WINWING MIP RAIL MOUNT MANUAL 10 50 mm bulge to this side 2x M8x16 flat head 2x slot nut M8 MTSIM WINWING MIP RAIL MOUNT MANUAL 11 2x pre-assembled universal connector 270mm profile MTSIM WINWING MIP RAIL MOUNT MANUAL 12 2x pre-assembled universal connector adjust position as needed 70mm profile MTSIM WINWING MIP RAIL MOUNT MANUAL 13 2x slot nut M8 cap cap MTSIM WINWING MIP RAIL MOUNT MANUAL 14 6x slot nut M8 cap cap 6x M8x18 black 6x washer Ø16 black MTSIM WINWING MIP RAIL MOUNT MANUAL 15 approx. 105 mm middle approx. 105 mm side view aligned Only 2x slot nut M5 are required for ICE MAN setup (one on each side) 2x slot nut M8 4x slot nut M5 2x slot nut M8 140 mm MTSIM WINWING MIP RAIL MOUNT MANUAL 16 cap cap MTSIM WINWING MIP RAIL MOUNT MANUAL 17 2x M5x40 (original from Winwing) 2x M5x40 (original from Winwing) MTSIM WINWING MIP RAIL MOUNT MANUAL 18 UFC unit assembly for ICE MAN setup M5x20 washer Ø15 M5x20 washer Ø15 MTSIM WINWING MIP RAIL MOUNT MANUAL 19 2x 4x slot nut M5 2x 2x slot nut M8 100 mm cap cap MTSIM WINWING MIP RAIL MOUNT MANUAL 20 2x 2x 2x M5x40 (original from Winwing) 2x M5x40 (original from Winwing) MTSIM WINWING MIP RAIL MOUNT MANUAL 21 2x M8x16 flat head black connector 2x M8x16 flat head black connector MTSIM WINWING MIP RAIL MOUNT MANUAL 22 2x washer Ø16 black 2x M8x18 black MTSIM WINWING MIP RAIL MOUNT MANUAL 23 2x washer Ø16 black 2x M8x18 black 2x washer Ø16 black 2x M8x18 black MTSIM WINWING MIP RAIL MOUNT MANUAL 24 2x slot nut M8 4x slot nut M5 100 mm cap cap MTSIM WINWING MIP RAIL MOUNT MANUAL 25 2x slot nut M8 2x M8x16 flat head black connector connector 2x M8x16 flat head black MTSIM WINWING MIP RAIL MOUNT MANUAL 26 2x M5x40 (original from Winwing) 2x M5x40 (original from Winwing) MTSIM WINWING MIP RAIL MOUNT MANUAL 27 ADJUSTMENTS Loosen the screws marked in red to move the parts shown in yellow up and down. Loosen the red marked screws on both sides to angle the yellow marked parts. MTSIM WINWING MIP RAIL MOUNT MANUAL 28 Loosen the screws marked in red to move the parts shown in yellow up and down. Loosen the screws marked in red to move the parts shown in yellow up and down. MTSIM WINWING MIP RAIL MOUNT MANUAL 29 Loosen the red marked screws on both sides to angle the yellow marked parts. MTSIM WINWING MIP RAIL MOUNT MANUAL 30 OPTION (parts must be ordered separately) Shown here in combination with a Table Mount MIP but works with Rail Mount MIP too. MTSIM WINWING MIP RAIL MOUNT MANUAL 31 Ø 8 40 PARTS (must be ordered separately) 1x 250 80 2x 30 M8 [dimensions in mm / different scales] No extra or spare parts listed! Profile for mounting plates Link for German orders. Link for international orders. Link for US orders. The universal connectors are included if you order the profile. 1x Mounting plate (comes with fitting screws and slot nuts) Link for German orders. Link for international orders. Link for US orders. MTSIM WINWING MIP RAIL MOUNT MANUAL 32 ASSEMBLY 2x slot nut M8 MTSIM WINWING MIP RAIL MOUNT MANUAL 33 turned universal connectors M8x30 turned back slot nuts as supplied with the mounting plate MTSIM WINWING MIP RAIL MOUNT MANUAL 34 Mounting plate as ordered. Screws as supplied with the mounting plate. 07-08-2023 WARNING NOTICES CAUTION! Do not clamp your fingers while attaching the rail mount. CAUTION! Check before usage if all screws are tightened. CAUTION! Check before usage that the instrument carrier is screwed on tight after making adjustments. DANGER: Contains small parts not suitable for children under 3 years. Only suitable for children over 12 years and adults. All MTSIM products are hand assembled and quality checked. The mount is designed for usage only with a computer controller (Winwing MIP). We exclude liability if the product is used for purposes other than intended. MTSIM shall be liable for damage arising from causes other than the detriment to life, body and health only to the extent that such damage arises from wilful misconduct, gross negligence or the culpable violation of a fundamental contractual obligation on the part of MTSIM or a vicarious agent (e.g. the delivery service) of MTSIM. Any further liability for damages shall be excluded. If you have safety concerns or questions regarding assembly, contact us under info@mtsim.com or visit www.mtsim.com/en/ WARNHINWEISE VORSICHT! Klemmgefahr bei der Montage der Schienenhalterung. VORSICHT! Achten Sie darauf, dass vor Benutzung alle Schrauben immer fest angezogen sind. VORSICHT! Achten Sie darauf, dass die Schienenhalterung nach dem Positionieren fest angezogen ist. GEFAHR: Nicht für Kinder unter 3 Jahren, Kleinteile - Verschluckungsgefahr! Nur für Kinder ab 12 Jahren und Erwachsene Alle Produkte der Firma MTSIM sind handgefertigt und qualitätsgeprüft. Die Halterung ist nur zur Verwendung in Kombination mit einem PC Controller (Winwing MIP) ausgelegt. Wir übernehmen keine Haftung für zweckentfremdete Benutzung. Für andere als durch Verletzung von Leben, Körper und Gesundheit entstehende Schäden haftet die MTSIM lediglich, soweit diese auf vorsätzlichem oder grob fahrlässigem Handeln oder auf schuldhafter Verletzung einer wesentlichen Vertragspflicht durch MTSIM oder eines Erfüllungsgehilfen (z. B. dem Zustelldienst) der MTSIM beruhen. Eine darüber hinausgehende Haftung auf Schadensersatz ist ausgeschlossen. Bei Fragen zur Sicherheit oder Aufbau unserer Produkte, wenden Sie sich an info@mtsim.com oder besuchen unsere Website unter www.mtsim.com NOTICES D`AVERTISSEMENT ATTENTION! Risque de coincement lors du montage de rail. ATTENTION! Vérifiez que toutes les vises sont correctement serrées avant utilisation. ATTENTION! Vérifier avant utilisation que le support collectif est bien vissé après avoir effectué les réglages. DANGER: Contient des petites pièces susceptibles d` être avalées. Ne convient pas aux enfants de moins de 3 ans. Utilisation appropriée pour enfants à partir de 12 ans et adultes. Tous les produits MTSIM sont fait main et on passés les contrôles de qualité. La fixation est conçue uniquement pour une utilisation avec un Winwing MIP. Nous dégageons toute responsabilité pour toute utilisation autre que celle prévue. Pour les dommages engendrés autres que l'atteinte corporelle, à la vie et à la santé, MTSIM n'est responsable que dans la mesure où ces dommages reposent sur un acte intentionnel, une faute lourde ou la violation fautive d'une obligation contractuelle essentielle par MTSIM ou par des agents délégués par MTSIM. Une responsabilité allant au-delà en dommages et intérêts est exclue. Si vous avez des questions concernant la sécurité ou l`assemblage, contactez-nous a info@mtsim.com ou visitez www.mtsim.com/fr/
Joystick / Throttle Mounting Plate – MTSIM – MONSTERTECHProfile for Mounting Plates – MTSIM – MONSTERTECHJoystick / Throttle Befestigungsplatte – MONSTERTECHProfil für Befestigungsplatte – MONSTERTECH
Joystick / Throttle Mounting Plate – MTSIM – MONSTERTECH USAProfile for Mounting Plates – MTSIM – MONSTERTECH USA