Ampeg Shop US
Ampeg
AmpegAmpegAmpeg Shop US
Login • Instagram
Owner's Manual for Ampeg models including: RB-108, RB-110, RB-112, RB-115, RB-210, RB-108 Bass Guitar Combo Amplifiers, RB-108, Bass Guitar Combo Amplifiers, Guitar Combo Amplifiers, Combo Amplifiers, Amplifiers
il y a 1 jour — Rocket Bass RB-108, RB-110, RB-112, RB-115, or RB-210 Amplifier, Power Cable, Quick Start Guide. Introduction. Designed from the ground up, with Ampeg's ...
Rocket Bass RB-108, RB-110, RB-112, RB-115, or RB-210 Amplifier, Power Cable, Quick Start Guide. Introduction. Designed from the ground up, with Ampeg's ...
Rocket Bass RB-108, RB-110, RB-112, RB-115, or RB-210 Amplifier, Power Cable, Quick Start Guide. Introduction. Designed from the ground up, with Ampeg's ...
File Info : application/pdf, 11 Pages, 1.96MB
DocumentDocumentRB-108, RB-110, RB-112, RB-115, and RB-210 Bass Guitar Combo Amplifiers Owner's Manual TABLE OF CONTENTS What's in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Rocket Bass Series Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Top Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Rear Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 RB-108 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 RB-110 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 RB-112 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 RB-115 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 RB-210 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Warranty and Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Supplier's Declaration of Conformity 47 CFR § 2.1077 Compliance Information Unique Identifiers: Ampeg® Rocket Bass RB-108, RB-110, RB-112, RB-115, and RB-210 amplifiers Responsible Party - U.S. Contact Information: Yamaha Guitar Group, Inc. 26580 Agoura Road Calabasas, CA 91302-1921 (818) 575-3600 https://ampeg.com/ FCC Compliance Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. © 2023 Yamaha Guitar Group, Inc. All rights reserved. Ampeg, the Ampeg logo, SGT, Super Grit Technology, and SVT are trademarks or registered trademarks of Yamaha Guitar Group, Inc. in the U.S. and/or other jurisdictions. Lavoce is a registered trademark of Lavoce Co., LTD Limited Company. The Model and Serial numbers can be found on the product label. Please record these numbers below and retain this document for your records. Model Number: ________________________________ Serial Number: ________________________________ 2 What's in the Box Rocket Bass® RB-108, RB-110, RB-112, RB-115, or RB-210 Amplifier, Power Cable, Quick Start Guide. Introduction Designed from the ground up, with Ampeg's industry standard tone and styling in mind, the all-new Rocket Bass combos feature the legacy Ampeg preamp and tone stack circuits with the widest range of classic Ampeg tones any Ampeg combo has ever offered. The new SGTTM (Super Grit Technology) overdrive circuit gives you the warmth and grit of a monster SVT® stack, packed into a lightweight combo that you can easily carry to any practice or performance. Iconic black diamond vinyl, reminiscent of the most recorded bass amp of all time, the Ampeg B15, wraps the most lightweight cabinets Ampeg has ever built, without sacrificing ground shaking lows and classic Ampeg tone. Integrated DIs, effect loops, and aux in/phones out circuits provide the ultimate tools for any rehearsal or gigging situation. Like all Ampeg products, your Rocket Bass combo is designed by musicians and built using only the best of components. Each combo is tested to confirm that it meets our specifications, and we believe that each amp is the best that it can be. In order to get the most out of your new combo, please fully read this Owner's Manual, as well as the Important Safety Instructions included with your Rocket Bass series amp, before you begin playing. Best of luck in all of your musical endeavors! - And THANK YOU for choosing Ampeg! - Rocket Bass Series Features · Superior Tone · Legacy Ampeg preamp and tonestack circuits · New SGT overdrive circuit · Perfectly-matched Lavoce® custom speakers* · Pro-Grade Flexibility · Super lightweight construction · Integrated DIs, effects loops, extension speaker outs* · Aux in / headphone outs · Iconic Styling · Ampeg's iconic black diamond vinyl · Impact-resistant metal corners · Rugged, braced enclosures *Some features available on select models only. 3 Top Panel Features 1. 15 dB INPUT: The attenuation of this 1/4" 8. ULTRA HI: This switch, when engaged, input is suited for use with basses that have enhances the amount of high frequency active electronics or high-output pickups. output with 5 dB boost at 8 kHz (RB-112, Connect here using a shielded instrument RB-115, RB-210). cable. 9. ULTRA LO: This switch, when engaged, 2. 0 dB INPUT: The signal output from a enhances the amount of low-end output with passive instrument may be connected to this a 1 dB boost at 40 Hz, and a 10 dB cut at 1/4" input. Connect here using a shielded 500 Hz (RB-112, RB-115, RB-210). instrument cable. 10. BASS: Use to adjust the low frequency level 3. SGT LED: This LED illuminates amber when of the amplifier. The low frequency output is the SGT overdrive circuit is on. flat at the center, "0" knob position. Rotate 4. SGT ON/OFF: Engage this switch to activate the control counter clockwise from 0 to the SGT overdrive circuit. This allows reduce the bass frequencies--or clockwise for varying amounts of tube-like grit and from 0 to increase the bass frequencies. distortion. See the following pages for Technical Specifications. 5. GRIT: Use to adjust the amount of SGT "grit." Turn the knob clockwise for a more 11. MIDRANGE: Use to adjust the midrange overdriven sound (RB-110, RB-112, RB-115, frequency level of the amplifier. The midrange RB-210). frequency level is flat at the center "0" knob position. Rotate the control counter clockwise 6. LEVEL: Use to control the overall level of for a "contoured" sound (more distant, less the SGT overdrive circuit. Turn the knob midrange output), or clockwise for a sound clockwise to increase the SGT level. (RB-110, that really cuts through (increased midrange). RB-112, RB-115, RB-210). See the following pages for Technical 7. VOLUME: Use to control the amplifier's Specifications. overall output level. It affects the preamp level fed to the Speaker and Phones outputs. Use it wisely and turn down when making connections, wearing headphones, or when trying something new. This control does not affect any signal coming into to the Aux Input (14). 12. TREBLE: Use to adjust the high frequency level of the amplifier. The high frequency level is flat at the center "0" knob position. Rotate the control counter clockwise from 0 to reduce the treble frequencies--or clockwise from 0 to increase the treble frequencies. See the following pages for Technical Specifications. 4 Top Panel Features 17. Horn On/Off Switch: Turns the high frequency horn on/off (RB-210 only). 18. EXT SPEAKER OUTPUT: Optionally, use this 1/4" TS output jack to connect to an 8 extension speaker cabinet. The internal speaker remains active when an extension speaker is connected. Use a non-shielded speaker cable with 1/4" TS ends to make the connections. Do not use shielded instrument cables as they may overheat. 19. SGT SWITCH: Optionally, connect a 1/4" TS footswitch to this jack for remote on/off 13. PHONES: Use this 1/8" TRS stereo output to connect your headphones. The output here is a mix of the line level signals reaching the amplifier, as well as any incoming audio from the Aux Input jack (14). Speaker output is control of the SGT circuit (RB-112, RB-115, RB-210). NOTE: A footswitch may be purchased at your local Ampeg Dealer, or directly from shop.ampeg.com. muted when Phones are connected. 20. EFFECTS LOOP SEND: Use a TS 14. AUX INPUT: The analog audio output from (unbalanced) cable from this 1/4" output to a line level source, such as an MP3 player or send a line level signal to an external effects other music source, can be connected to this processor. The output here is affected by all 1/8" input. controls. Use the Effects Loop Return jack to 15. ON LED: This LED illuminates blue when the amplifier's power is on. feed the returned processed signals back into the power amplifier--see item 21 (RB-112, RB-115, RB-210). 16. POWER SWITCH: Press the top of this switch to turn on the overall system power, and press the bottom of the switch to turn it off. 21. EFFECTS LOOP RETURN: Use a TS (unbalanced) cable into this 1/4" input to return the processed line level output of an Rear Panel Features external effects processor. The processor could be fed by signals from the Effects HORN Loop Send--see item 20 (RB-112, RB-115, RB-210). EXT SPEAKER 22. GROUND / LIFT SWITCH: Toggle to Lift to disable the ground connection at the Balanced DI Output jack if grounding hum SGT TM SWITCH or noise is present see item 23 (RB-110, RB-112, RB-115, RB-210). EFFECTS LOOP BALANCED DI OUT 23. BALANCED DI OUT: Connect this post-EQ, Post-SGT, mic level, balanced XLR output to the balanced input of an external mixer or recorder. In this configuration, you do not need to mic the speaker cabinet in order to add it to the main mix or to record (RB-110, RB-112, RB-115, RB-210) 5 RB-108 Technical Specifications FEATURE Output Power Rating Signal-to-Noise Ratio Maximum Gain @ 1 kHz Input Impedance Tone Controls Speaker Specs Maximum Operating Range SPECIFICATION VALUE 30 Watts RMS @ 4 10% THD+N 80 dB (20 Hz20 kHz unweighted) Input: 45 dB Normal Input: 500k Ohms -15dB Pad Input: 75k Ohms Bass: +18/20 dB @ 40 Hz Mid: +14/10 dB @ 500 Hz Treble: +16/18 dB @ 4 kHz 1 x 8" speaker, 4 45° C ambient temperature, 93% relative humidity, up to 2000 m altitude Power Requirements 100240V ~ 50-60 Hz, 45W Max Size (H x W x D) Weight (Approximate) 17 x 16.2 x 12 inches 433 x 411 x 306 mm 23 lbs 10.45 kg All specifications subject to change. 6 RB-110 Technical Specifications FEATURE Output Power Rating Signal-to-Noise Ratio Maximum Gain @ 1 kHz Input Impedance Tone Controls Speaker Specs Maximum Operating Range SPECIFICATION VALUE 50 Watts RMS @ 4 10% THD+N 84 dB (20 Hz20 kHz unweighted) Input: 48.5 dB Normal Input: 1Meg Ohms -15dB Pad Input: 75k Ohms Bass: +14/13 dB @ 40 Hz Mid: +15/9 dB @ 500 Hz Treble: +12/20 dB @ 4 kHz 1 x 10" speaker, 4 45° C ambient temperature, 93% relative humidity, up to 2000 m altitude Power Requirements 100-240V ~ 50-60 Hz, 70W Max Size (H x W x D) Weight (Approximate) 19 x 16.2 x 13 inches 481 x 411 x 330 mm 22.5 lbs 10.20 kg All specifications subject to change. 7 RB-112 Technical Specifications FEATURE Output Power Rating SPECIFICATION VALUE 100 Watts RMS @ 4 10% THD+N Signal-to-Noise Ratio Maximum Gain @ 1 kHz Input Impedance Tone Controls Speaker Specs 80 dB (20 Hz20 kHz unweighted) Input: 48.5 dB Aux Input: 33 dB Effects Return: 29 dB Normal Input: 1Meg Ohms -15dB Pad Input: 75k Ohms Bass: +14/13 dB @ 40 Hz Mid: +15/9 dB @ 500 Hz Treble: +12/20 dB @ 4 kHz 1 x 12" custom Lavoce speaker, 4 Maximum Operating Range 45° C ambient temperature, 93% relative humidity, up to 2000 m altitude Power Requirements 100240V AC ~ 50-60 Hz, 150W Max Size (H x W x D) Weight (Approximate) 21.4 x 18.2 x 14.2 inches 543 x 462 x 360 mm 25.9 lbs 11.75 kg All specifications subject to change. 8 RB-115 Technical Specifications FEATURE Output Power Rating Signal-to-Noise Ratio Maximum Gain @ 1 kHz Input Impedance Tone Controls Speaker Specs SPECIFICATION VALUE 200 Watts RMS @ 4 0.5% THD+N (with external speaker) 100 Watts RMS @ 8 0.5% THD+N 90 dB (20 Hz20 kHz unweighted) Input: 60 dB Aux Input: 39 dB Effects Return: 32 dB Normal Input: 1Meg Ohms -15dB Pad Input: 75k Ohms Bass: +14/9 dB @ 40 Hz Mid: +15/9 dB @ 500 Hz Treble: +12/24 dB @ 4 kHz 1 x 15" custom Lavoce speaker, 8 Maximum Operating Range 45° C ambient temperature, 93% relative humidity, up to 2000 m altitude Power Requirements 100240V ~ 50-60 Hz, 280W Max Size (H x W x D) Weight (Approximate) 22.4 x 20.2 x 13.94 inches 570 x 513 x 354 mm 33.4 lbs 15.45 kg All specifications subject to change. 9 RB-210 Technical Specifications FEATURE SPECIFICATION VALUE Output Power Rating 500 Watts RMS @ 4 5% THD+N (with external speaker) 250 Watts RMS @ 8 2% THD+N Signal-to-Noise Ratio 91 dB (20 Hz20 kHz unweighted) Maximum Gain @ 1 kHz Input Impedance Tone Controls Speaker Specs Input: 73 dB Aux Input: 52 dB Effects Return: 36 dB Normal Input: 1Meg Ohms -15dB Pad Input: 75k Ohms Bass: +14/9 dB @ 40 Hz Mid: +15/9 dB @ 500 Hz Treble: +12/24 dB @ 4 kHz 2 x 10" custom Lavoce speakers, 16 1 HF compression driver each (8 in parallel) Maximum Operating Range 45° C ambient temperature, 93% relative humidity, up to 2000 m altitude Power Requirements 100240V ~ 50-60 Hz, 600W Max Size (H x W x D) Weight (Approximate) 25.75 in x 20.2 in x 13.94 inches 654 x 513 x 354 mm 38 lbs 17.7 kg All specifications subject to change. 10 Warranty and Support Visit WWW.AMPEG.COM to... (1) ...identify WARRANTY coverage provided in your local market. Please keep your sales receipt in a safe place. (2) ...REGISTER your product. (3) ...CONTACT Technical Support, or call 818-575-3600. www.ampeg.com Yamaha Guitar Group, Inc. 26580 Agoura Road, Calabasas, CA 91302-1921 USA Rev. C