Philips Dynalite Support
Installation Guide for Dynalite models including: PDDEG-S, PDDEG-S Ethernet Gateway Supervisor, Ethernet Gateway Supervisor, Gateway Supervisor, Supervisor
Resources – Philips Dynalite
File Info : application/pdf, 4 Pages, 1.47MB
DocumentDocumentPDDEG-S Ethernet Gateway Supervisor Installation Instructions Instructions d'installation Installationsanweisungen Instrucciones de instalación Istruzioni per l'installazione Installatie-instructies Devices must be installed in an approved enclosure by a qualified electrician in accordance with all national and local electrical and construction codes and regulations. Les appareils doivent être installés dans un lieu jugé apte, par un électricien qualifié et conformément aux règles et normes locales et nationales en matière d'électricité et de construction. Die Geräte müssen von einem geprüften Elektriker entsprechend allen nationalen und lokalen Elektro und Bauvorschriften in einem zugelassenen Gehäuse installiert werden. Los dispositivos se deben instalar en un recinto aprobado por un electricista cualificado de acuerdo a todos los reglamentos eléctricos y de construcción locales y nacionales pertinentes I dispositivi devono essere installati da un elettricista qualificato in un luogo approvato, in conformità a tutti gli standard e le norme nazionali e locali vigenti in materia di impianti elettrici e costruzioni edilizie. Apparaten moeten door een erkende elektricien worden geïnstalleerd in een goedgekeurde behuizing in overeenstemming met alle nationale en lokale elektriciteits en bouwvoorschriften en wetgeving. / 104 mm (4.09 in) 95 mm (3.74 in) 1A IEC Pollution Degree II 216 mm (8.50 in) 64 mm (2.52 in) 45 mm (1.77 in) 45 mm (1.77 in) 50° C (122° F) 0° C (32° F) 90% 68 mm (2.68 in) 1B 160 mm (6.30 in) 45 mm (1.80 in) 45 mm (1.80 in) 2 3 Ethernet 1 Ethernet 2* SHLD GND D+ D+12 V AUX GND AUX < 20 m 0.3-2.5mm2 22-12 AWG 0.4 Nm 3.5 Lb-in 2 A RS-485 DyNet RJ45 Ethernet *Refer to dynalite.com/support for port 2 availability. 4 5 0.2-5 mm2 24-10 AWG 6 Link Link Connecting Connected Ethernet 1 Ethernet 2 Cloud Service LED OK OK, Network busy Booting (60 s) Fault 7 NL 100-277 V 0.25 A IEC Overvoltage Category III µP SHLD GND D+ D+12 V AUX 12V 300 mA RS-485 DyNet RJ45 Socket RJ45 Socket Ethernet 1 Ethernet 2 SELV / Class 2 (UL) 8 A BACnet Integration BACnet (BMS LAN) Ethernet Lighting LAN We recommend connecting the BMS and lighting systems on different VLANs. 8B Ethernet RS-485 DyNet RS-485 DyNet 8C 9 Ethernet RS-485 DyNet FCC and RSS-210 of IC (Industry Canada) Rules This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules and pursuant to RSS210 of the IC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any modifications not approved by the manufacturer of this device could void the user's authority to operate this device. This Class B digital apparatus complies with Canadian ICES-003: CAN ICES-3(B)/NMB-3(B). Cet appareil numerique de la Classe B est conforme a la norme NMB-003 du Canada: CAN ICES-3(B)/NMB-3(B). Installation of a home and building automation and control system shall comply with IEC 60364 (all parts). The temperature limits and current-carrying capacities for the communication wires specified in IEC 60364-5-52 shall not be exceeded. © 2024 Signify Holding. All rights reserved. Specifications are subject to change without notice. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their respective owners. www.dynalite.com AZZ 508 0724 R14