QUICK START GUIDE
XPG PROBE BRONZE POWER SUPPLY
3 YEAR LIMITED WARRANTY
PROBE 700 BRONZE SPECIFICATION
SPEC Label & Safety Instructions
Packaging Content
- XPG PROBE Bronze Power Supply Unit
- AC Power Cord
- User Manual
- PSU Screw x 4
Specifications Table
| Attribute | PROBE700BRONZE |
|---|---|
| Model Number | PROBE700BRONZE |
| AC Input | 100-240V 10A 47-63Hz |
| DC Output | +5V, +3.3V, +12V, -12V, +5VSB |
| Output Current | 17A, 19A, 54A, 0.3A, 2.5A |
| Output Wattage | 110W, 648W, 3.6W, 12.5W |
| Total Continuous Power | 700W |
Fan Curve Description
The fan speed increases from 400rpm to 2000rpm as the load condition goes from 10% Light to Full, at a temperature of 25°C.
DC Cable Listing
For PROBE 700 BRONZE:
- Motherboard 20+4 Pin: 500mm (1)
- ATX 12V 8 Pin: 500mm (1)
- ATX 12V 4+4 Pin: 500mm (1)
- PCI-E 6+2 Pin: 500mm (2)
- SATA: 450mm (2), 150mm (3)
- Molex: 150mm (2)
Cable Connector Quantities Summary:
| Connector Type | Quantity |
|---|---|
| Motherboard 20+4 Pin | 1 |
| ATX 12V 4+4 Pin to 4+4 Pin (CPU) | 1 |
| PCI-E 6+2 to 6+2 Pin | 2 |
| SATA | 5 |
| Molex | 2 |
PROBE 600 BRONZE SPECIFICATION
SPEC Label & Safety Instructions
Packaging Content
- XPG PROBE Bronze Power Supply Unit
- AC Power Cord
- User Manual
- PSU Screw x 4
Specifications Table
| Attribute | PROBE600BRONZE |
|---|---|
| Model Number | PROBE600BRONZE |
| AC Input | 100-240V 9A 47-63Hz |
| DC Output | +5V, +3.3V, +12V, -12V, +5VSB |
| Output Current | 17A, 19A, 46A, 0.3A, 2.5A |
| Output Wattage | 110W, 552W, 3.6W, 12.5W |
| Total Continuous Power | 600W |
Fan Curve Description
The fan speed increases from 400rpm to 2000rpm as the load condition goes from 10% Light to Full, at a temperature of 25°C.
DC Cable Listing
For PROBE 600 BRONZE:
- Motherboard 20+4 Pin: 500mm (1)
- ATX 12V 8 Pin: 500mm (1)
- ATX 12V 4+4 Pin: 500mm (1)
- PCI-E 6+2 Pin: 450mm (2)
- SATA: 150mm (3)
- Molex: 150mm (2)
Cable Connector Quantities Summary (as per table):
| Connector Type | Quantity |
|---|---|
| Motherboard 20+4 Pin | 1 |
| ATX 12V 4+4 Pin to 4+4 Pin (CPU) | 1 |
| PCI-E 6+2 to 6+2 Pin | 2 |
| SATA | 5 |
| Molex | 2 |
INSTALLING YOUR NEW PROBE POWER SUPPLY
Important: Make sure that your system is turned off and unplugged before you start installing it. Disconnect the AC power cord from your old power supply if any.
- Remove the power supply from its packaging.
- Install the PSU into the case with the four screws provided.
- Connect the 24-pin ATX cable to the motherboard 24-pin power socket.
- Connect the EPS 12V 8 / 4+4pin cable to the CPU power socket.
- Connect SATA power cables to any devices that may use 4-pin peripheral connectors, i.e. hard drives, solid state drives, optical drives.
- Connect the corresponding PCI-E connector as instructed by your graphic card's user manual, if your graphic card requires additional PCI-E power. Please note that the power supply utilizes a 6+2pin PCI-E connector that can be effectively used either as a single 8pin or a 6pin PCI-E connector. To use it as a 6pin PCI-E connector, please detach the 2pin connector portion from the connector header.
- Connect the peripheral/floppy disk 4pin connector for fans, pumps, legacy components and other devices/adaptors.
- Connect the AC Power cord to both your power supply and to the wall. Check all connections to ensure that every item is properly plugged in and turn the power switch of the power supply to the ON position.
TROUBLESHOOTING
If your system does not turn on after installing the power supply, please follow the troubleshooting guide listed below:
- Please make sure the AC main power cord is connected to your PC correctly and that your power outlet is properly emitting power.
- Please make sure the AC On/Off switch on the back panel of the power supply unit is in the "I" (On) position.
- Please make sure that the MB & CPU Power Socket & connectors are connected correctly on the motherboard.
- If you still have problems turning on your PC, please contact ADATA Tech Support, Service Center or your local dealer.
WARRANTY INFORMATION
Duration of Warranty
ADATA Technology Co., Ltd. provides a 3-year warranty period for this product unless regional laws and regulations state otherwise.
Limitation of Warranty
This limited warranty covers only repairs or replacements of products manufactured by ADATA Technology Co. Ltd. and its authorized partners. ADATA is responsible for providing free repairs except for the following reasons:
- The warranty label is altered, damaged or missing.
- Product serial number does not conform to our original system.
- Product was purchased from an unauthorized agent.
- Damage caused by natural calamity.
- Any abuse outside the intended product operation.
Online Customer Service
For frequently asked questions, additional information and service instruction please visit our product page www.xpg.com.
INTEGRATED PROTECTION CIRCUITS
- OVP: Over Voltage Protection
- UVP: Under Voltage Protection
- OPP: Over Power Protection
- OTP: Over Temperature Protection
- SCP: Short Circuit Protection
- SIP: Surge and Inrush Protection
COMPANY INFORMATION & COMPLIANCE
EU REP: ADATA Technology B.V., Address: Transpolispark, Siriusdreef 17-27, 2132 WT, Hoofddorp, The Netherlands. E-mail: adata_europe@adata.com
UK REP: APEX CE SPECIALISTS LIMITED, Address: 89 Princess Street, Manchester, M1 4HT, UK. E-mail: adata_europe@adata.com
Compliance:
- WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
- www.adata.com/rohs/ (RoHS compliance)
- CAN ICES-003(B)/NMB-003(B)
- CERTIFICADO ID 1111222829
RESTRICTED SUBSTANCES
The following table indicates the presence or absence of restricted substances in product components.
| Component Name | Unit | Lead (Pb) | Mercury (Hg) | Cadmium (Cd) | Hexavalent Chromium (Cr VI) | PBB | PBDE |
|---|---|---|---|---|---|---|---|
| Case | ○ | ||||||
| Wire | ○ | ||||||
| The main circuit board | ○ | ||||||
| Resistor | ○ | ||||||
| Capacitance | ○ | ||||||
| SMD DIODE | ○ | ||||||
| IC | ○ | ||||||
| Transformer/coil | ○ | ||||||
| FUSE | ○ | ||||||
| Plastic parts | ○ | ||||||
| Packaging materials | ○ |
Key:
- ○: Indicates that the percentage content of the restricted substance does not exceed the reference value.
- (Blank): Indicates that the restricted substance is not present or is an exemption.
Note: Exceeding 0.1wt% and Exceeding 0.01wt% indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition.
P65Warnings.ca.gov
