Philips Customer Service Support - Home | Philips
User Manual for Mmd Hong Kong Holding models including: TAFW1RE, 2AR2STAFW1RE, FW1 Wireless Subwoofer and Speaker, FW1, Wireless Subwoofer and Speaker, TAFW1RE 37, Wireless Subwoofer TAFW1 37
MMD Hong Kong Holding Limited TAFW1RE Wireless subwoofer 2AR2STAFW1RE 2AR2STAFW1RE tafw1re
File Info : application/pdf, 12 Pages, 2.93MB
DocumentDocumentFidelio Wireless Subwoofer TAFW1/37 TAFW1RE/37 User manual Register your product and get support at www.philips.com/support Contents 1 Important safety instructions 3 Safety 3 Care for your product 4 Care of the environment 4 Declaration of conformity 4 Help and support 5 FCC information 6 2 Your Subwoofer 7 What's in the box 7 Subwoofer 8 3 Connect 9 Connect to power 9 Pairing with FB1 soundbar 9 Wi-Fi Set up 10 Wired connection (Sub-in) 13 Upgrade rmware 14 Factory reset 14 5 Product specifications 15 6 Troubleshooting 16 2 EN 1 Important safety instructions Read and understand all instructions before you use your product. If damage is caused by failure to follow instructions, the warranty does not apply. Safety Know these safety symbols CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This is CLASS II apparatus with double insulation, and no protective earth provided. AC voltage Follow the instructions in the user manual! WARNING! Warning: Risk of electric shock! The exclamatory mark is intended to alert the user to the presence of important operating instructions. Risk of electric shock or fire! · Before you make or change any connections, make sure that all devices are disconnected from the power outlet. · Never expose the product and accessories to rain or water. Never place liquid containers, such as vases, near the product. If liquids are spilt on or into the product, disconnect it from the power outlet immediately. Contact Consumer Care to have the product checked before use. · Never place the product and accessories near naked flames or other heat sources, including direct sunlight. · Never insert objects into the ventilation slots or other openings on the product. · Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. · Disconnect the product from the power outlet before lightning storms. · When you disconnect the power cord, always pull the plug, never the cable. · Use the product in tropical and/or moderate climates. Risk of short circuit or fire! · For identication and supply ratings, see the type plate at the back or bottom of the product. · Before you connect the product to the power outlet, ensure that the power voltage matches the value printed on the back or bottom of the product. Never connect the product to the power outlet if the voltage is different. Risk of injury or damage to this product! · For wall mounting, this product must be securely attached to the wall in accordance with the installation instructions. Use only the supplied wall mount bracket (if available). Improper wall mounting may result in accident, injury or damage. If you have any query, contact Consumer Care in your country. · Never place the product or any objects on power cords or on other electrical equipment. EN 3 · If the product is transported in temperatures below 5°C, unpack the product and wait until its temperature matches room temperature before connecting it to the power outlet. · Parts of this product can be made of glass. Handle with care to avoid injury and damage. Risk of overheating! · Never install this product in a conned space. Always leave a space of at least four inches around the product for ventilation. Ensure curtains or other objects never cover the ventilation slots on the product. Note · The rating label is pasted on the bottom or back of the equipment. Care for your product Use only microfiber cloth to clean the product. Care of the environment Disposal of your old product and battery Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. This symbol on a product means that the product is covered by European Directive 2012/19/EU. This symbol means that the product contains batteries covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. 4 EN Inform yourself about the local separate collection system for electrical and electronic products and batteries. Follow local rules and never dispose of the product and batteries with normal household waste. Correct disposal of old products and batteries helps prevent negative consequences for the environment and human health. EN For 5G Wi-Fi Device The device for operation in the band 51505350 MHz is only for indoor use to reduce the potential for harmful interference to cochannel mobile satellite systems. FR Pour un appareil Wi-Fi 5G les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l'intérieur an de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux. Declaration of conformity This product complies with the radio interference requirements of the European community. Hereby, MMD Hong Kong Holding Limited declares that the product is in compliance with the essential requirements and other relevant provisions of RED Directive 2014/53/EU and UK Radio Equipment Regulations SI 2017 No 1206. You can find the Declaration of Conformity on www.philips.com/support. Help and support For extensive online support, visit www.philips.com/support to: · download the user manual and the quick start guide · watch video tutorials (available only for selected models) · find answers to frequently answered questions (FAQs) · email us a question · chat with our support representative. Follow the instructions on the website to select your language, and then enter your product model number. Alternatively, you can contact Consumer Care in your country. Before you contact, note down the model number and serial number of your product. You can find this information on the back or bottom of your product. Trademarks: For DTS patents, see http://patents.dts. com. Manufactured under license from DTS, Inc. (for companies headquartered in the U.S./Japan/Taiwan) or under license from DTS Licensing Limited (for all other companies). DTS, DTS Play- , Play and the DTS Play- and Play- logos are registered trademarks or trademarks of DTS, Inc. in the United States and other countries. © 2021 DTS, Inc. ALL RIGHTS RESERVED. The Wi-Fi CERTIFIEDTM Logo is a registered trademark of Wi-Fi Alliance®. EN 5 FCC information NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio / TV technician for help. FCC&IC Warning: · This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. · Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC & IC Attention · Cet appareil est conforme à FCC et IC l'exposition aux rayonnements limites xées pour un environnement non contrôlé. Cet appareil doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur 6 EN et votre corps. Cet transmetteur ne doit pas être co-situé ou opérant en liaison avec toute autre antenne ou transmetteur. · Des câbles blindés doivent être utilisés avec cet apparei l pour assurer la conformité avec les limites de la classe B de la FCC. fonctionnement de I'appareil. IC-Canada: CAN ICES-003(B)/NMB003(B) This device contains licence-exempt transmitter(s) / receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: 1 This device may not cause interference. 2 This device must accept any interference, including interference that may cause undesired operation of the device. Avis d'Industrie Canada: CAN ICES003(B)/NMB-003(B) L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1 L'appareil ne doit pas produire de brouillage; 2 L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. 2 Your Subwoofer Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your subwoofer at www.philips.com/support. Headphones Series CTN Quick Start Guide x1 What's in the box Check and identify the items in the package: Warranty Card x1 Safety Information Subwoofer x1 Power Cord * x1 · Power cord quantity and plug type vary by regions. CCC BSMI UL VDE BS VDE BS SAA Safety Sheet x1 · Images, illustrations and drawings shown on this User Manual are for reference only, actual product may vary in appearance. for China FW1/93 for Taiwan FW1/96 for US/Canada FW1/37 for Europe/UK FW1/10 for Asia FW1/98 EN 7 Subwoofer This section includes an overview of the wireless subwoofer. 12 3 9 4 5 8 6 25Hz 7 10 1 (Wi-Fi Setup) button / indicator · Trigger Wi-Fi setup for Play-. · Press and hold the button for 8 seconds to active the AP mode. · Press and hold the button for 4 seconds to active the WPS mode. · Press and hold the button for 15 seconds to reset the factory default settings of the subwoofer. Action Press and hold 8 seconds Press and hold 4 seconds LED State Constant on Blink Double blink Status Connected / Pairing successful Wi-Fi Access Point (AP) mode Wi-Fi Protected Setup (WPS) mode 2 Power/RF link indicator 3 Source (switch Play-fi/FR link/Sub in mode) · When FW1 is used as a wired subwoofer, source switch must be at Sub in position. » All network audio functionality will stop working. » Wi-Fi is disconnected but Wi-Fi credentials shall be retained if it is setup previously. » Play- module can be turned off. · To upgrade rmware for Play- module and MCU via USB service port, source switch must be at Sub in position. 4 USB service socket The USB socket is for service only. 5 Reset button (Pin hole) Reset device to default setting. 6 Phase 0° - 180° (switch) 7 Sub in (socket) Use the subwoofer cable to connect the subwoofer to the soundbar (not supplied). 8 Crossover 25Hz-150Hz (knob) 9 Gain +/- (knob) Functional Settings Gain -6 dB to +6 dB Crossover 25 to 150 Hz Phase 0 or 180 degree Default 0 dB 0 degree When FW1 as Play- subwoofer, above controls and functions are not applicable. 10 AC in ~ socket Connect to the power supply. 8 EN 3 Connect Connect to power This section helps you connect your subwoofer to a TV and other devices, and then set it up. Note · For identication and supply ratings, see the type plate at the back or bottom of the product. · Before you make or change any connections, make sure that all devices are disconnected from the power outlet. Fidelio FB1 ON Fidelio FW1 Fidelio FW1 Preamp Subwoofer Output out Fidelio FW1 Sub in · Pairing with FB1 soundbar, go to page 9. · Wi-Fi Set up, go to page 10. · Connect the subwoofer to Philips Play- enabled TV, go to page 12. · Wired connection, go to page 13. WARNING! · Risk of product damage! Make sure that the power supply voltage corresponds to the voltage printed on the back or the underside of the product. · Risk of electric shock! When you unplug the power cord, always pull the plug from the socket. Never pull the cord. · Before connecting the AC power cord, ensure you have completed all other connections. Connect the mains cable to the AC in~ socket of the subwoofer and then into a mains socket. 1 or or AC in ~ * Power cord quantity and plug type vary by regions. Pairing with FB1 soundbar (RF-link initial set up) FW1 Play-Fi wireless subwoofer can pair with FB1 (not supplied) soundbar. 1 The source switch must be at Play-fi/ RF Link position. 2 The Power/RF link indicator will (Green) fast blink on the Subwoofe. 3 Press the button to turn your FB1 soundbar on. 4 Goto soundbar settings menu ( press ) and select "SUB PAIR". Then press (Enter) to enter the subwoofer pairing mode. EN 9 5 Wait until the Power/RF link indicator will light up solid on the subwoofe. 6 Soundbar and subwoofer shall discover each other and pair. 1 2 (Green) Fast blink 2 Download and install the Philips Sound app powered by DTS Play- on a phone or tablet. · Make sure your router is turned on and working properly. · When FW1 is used as a Play- subwoofer, source switch must be at Play-fi/RF Link position. Wi-Fi <Wi-Fi 2 3 ON 4 SUB PAIR FB1 SoundBar 5 (Green) Solid FB1 SoundBar 6 ON Wi-Fi Set up (For iOS and Android version) By connecting this unit and mobile phones, tablets (such as iPad, iPhone, iPod touch, Android phones, etc.) to the same Wi-Fi network, you can then use the Philips Sound app powered by DTS Play- to control the subwoofer to listen to audio les. 1 Connect your phone or tablet to the same Wi-Fi network that you want to connect your subwoofer. Philips Sound Two tone 8 sec Fast blink Slow pulse 3 Press and hold (Wi-Fi) button located at the back cabinet for 8 sec to trigger the Wi-Fi connection. » Until the speaker make a second tone and then release the button. 4 Wait until the Wi-Fi light indicator on the back cabinet goes from a fast blink to a slow pulse. When it begins pulsing slowly, it indicates that the speaker is entering the Wi-Fi setup mode. 5 Launch the Philips Sound app powered by DTS Play-. Follow the instructions in the app to connect this product to your Wi-Fi network. 10 EN Philips Sound Return to this app to continue setup. Ready? Go To Wi-Fi Settings PlayFiDevice 1234 Settings SETUP Setup Play-Fi Device Your Home Router Wi-Fi Password 1234567890I X Enter the password for the network Your Home Router Show Password. Your Play-Fi device is connecting to Your Home Router When the Wi-Fi light on the device stops blinking and becomes solid the device is setup and ready to be used. X Select Name Bedroom 6 After successful Wi-Fi connection, the Wi-Fi light indicator will stop pulsing and turn solid. Once you set up this product on your Wi-Fi network, you can control it from any smartphone or tablet on the same network. 7 After connection, you can change the device name. There are several names to choose from or create your own by choosing Custom Name at the end of the name list. Otherwise, it follows the default name. 8 After connection, this product may perform a software update. Upgrade to the latest software when it is your rst time set up. The software upgrade may take several minutes. Do not unplug your speaker, turn off your device, or leave the network during the update. Note · After connection, the product may perform a software update. Upgrade is required after initial set up. Without the upgrade, not all product features can be available. · When the rst time set up is not successful, hold down the Wi-Fi button on the subwoofer for 8 seconds until the second tone can be heard and the Wi-Fi light is changed to a slow pulse. Reset the Wi-Fi connection, restart the app and start the set up again. · If you want to change from one network to another, you need to set up the connection again. Press hold down the (Wi-Fi) button on the subwoofer for 8 seconds to reset the Wi-Fi connection. Wi-Fi Protected Setup (WPS) If your router has Wi-Fi Protected Setup (WPS), you can set up the connection without entering a password. One tone 4 sec Double blink WPS Philips Sound 4 DevicSeest Up Play-Fi Device 1 Press and hold the (Wi-Fi) button for 4 seconds. » You will hear a tone and the Wi-Fi light will begin double blink. 2 Press the WPS button on your router. The button is normally marked with this WPS logo. 3 Follow the instruction in Philips Sound app powered by DTS Play- to start the pairing. Note · WPS is not a standard feature on all routers. If your router does not have WPS then use Standard Wi-Fi Setup. · Press the (Wi-Fi) button once if you want to exit the WPS mode or it will automatically exit after 2 minutes. EN 11 Connect the subwoofer with Philips Sound app 1 After successful Wi-Fi connection, the Wi-Fi light indicator will stop pulsing and turn solid. 2 Launch the Philips Sound app powered by DTS Play- . 3 Select the Primary Speaker [FW1]. Connect the subwoofer to Philips Play-fi enabled TV 1 Power up your DTS Play- TV connected to the internet. » TV sound is muted. 2 Enter the Settings menu on TV. » Settings > Sound > DTS Play- 1 TV Solid Philips Sound XXXXX Speakers Solid Settings Picture Sound > 2> Ambilight > Eco settings > General settings > Regionand language Android settings > Universal access > Sound style Personal mode settings > TV placement DTS Play-Fi 3 Room calibration > Mimi Sound Personalization ... > Advanced Dolby Atmos n>otication FW1 Primary Speaker 12 EN