Important Safety Instructions
IMPORTANT: Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in serious injury. Save all warnings and instructions for future reference.
Legends and Symbols
When you come across the safety-alert symbol on your equipment or in this manual, pay attention to the following signal words and remain vigilant about the potential for personal injury.
- ⚠️ DANGER: Ignoring these hazards can result in death, severe personal injury, or significant property damage.
- ❗ WARNING: Indicates potential hazards that can result in severe personal injury, death, or significant property damage. Ignoring these warnings presents a real danger.
- ? CAUTION: Indicates potential hazards that can result in minor or moderate personal injury, property damage, or actions that are unpredictable and unsafe. Ignoring these cautions presents a potential hazard.
- ℹ️ NOTICE: This label indicates important special instructions that are not directly related to hazards.
USE OF NON-XTREMEPOWERUS REPLACEMENT PARTS VOIDS WARRANTY
ATTENTION INSTALLER: This manual contains vital information regarding the installation, operation, and safe use of this product. It is essential to provide this manual to the end user of the product. Failure to read and follow all instructions could lead to severe injuries.
? NO JUMPING
? NO DIVING
WARNING: The gap between the pool's inner wall and the ladder must not exceed 4 inches to prevent entrapment. If the gap is over 4 inches, install the safety kit to prevent drowning.
CAUTION:
- Prevent ladder damage and minimize injury risk by following these careful instructions.
- Install the ladder on a solid base.
- For pool ENTRY / EXIT, face the pool at all times.
- This ladder is only for entering and exiting the pool. Using it for any other purpose may damage the ladder and pool structure.
- To prevent entrapment or drowning, do not swim through, behind, or around the ladder.
- Maximum weight limit: 225 LBS.
NOTE:
- This ladder is intended for use with above-ground pools measuring 48", 52", or 54" in height.
- For winter, remove the ladder from the pool and store it in a dry place.
Overview (Product Information)
Package Contents
The package includes the following parts:
- Part 1: Base (1 PC)
- Part 2: Ladder Frame (1 PC)
- Part 3: Handrail (2 PC)
- Part 4: Feet (2 PC)
- Part 5: Screw (2 PC)
- Part 6: Washer (2 PC)
- Part 7a: Screw (4 PC)
- Part 7b: Washer (4 PC)
- Part 7c: Nut (2 PC)
- Part 7d: Gasket (2 PC)
- Part 7f: Gasket (12 PC)
- Part 7g: Screw (12 PC)
Dimensions
The ladder has the following approximate dimensions:
- Overall Height: 75.4 inches
- Base Width: 28.9 inches
- Top Width: 26.6 inches
- Step Spacing (approximate): 10.0 inches between steps, with the bottom step at 9.7 inches from the base.
Specifications
| MODEL | 75220 |
|---|---|
| MATERIAL | PP |
| PRODUCT WEIGHT | 23.57 LBS |
| DIMENSIONS | 26.6" x 75.4" x 28.9" |
| ADJUSTABLE HEIGHT | 48" / 52" / 54" |
Assembly Instructions
Step 1
Assemble the base (Part 1) by attaching two feet (Part 4) to the "U" shaped ladder base (Part 1). Use one stainless steel screw (Part 5), one washer (Part 6), and one plastic cap (Part 7) per foot. Refer to Figure A for visual guidance.
Step 2
Insert the ladder frame (Part 2) into the base assembly. Match the ladder frame (Part 2) and base to the pool height: 48", 52", or 54". Secure by inserting four bolts (Part 8) through the pre-drilled holes and tighten with washers (Part 9) and nuts (Part 10). Refer to Figure B for visual guidance.
NOTE: A mallet or similar tool may be used for a more compact fit during installation.
Step 3
Alignment is key. If necessary, adjust with appropriate tools. Place the handrails (Part 3) into the assembled ladder. Refer to Figure C for visual guidance.
Step 4
Fit the bases (Part 11) to the ends of the handrails and secure with the provided screws (Part 12) and washers (Part 13). Adjust the height as needed. Refer to Figure D for visual guidance.
Step 5
Firmly secure the bases (Part 11) to the platform, using the washers (Part 13) and screws (Part 12). Refer to Figure E for visual guidance.
WARNING:
- Maintain a space of 4 inches or less between the pool's inner wall and the ladder to avoid the risk of becoming trapped.
- This ladder is designed solely for getting into and out of the pool. Misuse could cause damage to both the ladder and the pool's structure.
- A gap exceeding 4 inches necessitates the installation of a safety kit to prevent the risk of accidental drowning.
Replacement Parts
Parts Diagram
A diagram illustrates the placement of all parts. The parts are labeled with numbers and letters (e.g., PARTS#: 1, PARTS#: 7a).
Parts List
| PARTS # | REFER. # | DESCRIPTION | QUANTITY |
|---|---|---|---|
| 1 | 47153901001 | HANDRAIL | 2 |
| 2 | 47153902001 | PEDAL BRACKET | 1 |
| 3 | 647153971000 | TELESCOPIC SUPPORT ASSEMBLY | 1 |
| 4 | 47153906001 | BASE | 2 |
| 5 | 47153905001 | HANDRAIL MOUNT | 2 |
| 6 | 47153907001 | SCREW CAP | 2 |
| 7 | 65862082000 | HARDWARE PACK | 1 |
| 7 a | SCREW ST4.2*25-C-H | 12 | |
| 7 b | WASHER M5 | 12 | |
| 7 c | NUT M6 | 4 | |
| 7 d | GASKET Ф6*Ф16*1 | 4 | |
| 7 e | BOLTS M6*75 | 4 | |
| 7 f | GASKETS Φ6*25*1.5 | 2 | |
| 7 g | SCREWS ST5.5*25-C-H | 2 |
Disclaimer
The manufacturer and/or distributor have provided the parts list and assembly diagram in this manual for reference purposes only. They do not make any representation or warranty to the buyer that they are qualified to make repairs to the product or replace any parts of the product. In fact, the manufacturer and/or distributor expressly state that all repairs and parts replacements should be undertaken by certified and licensed technicians, and not by the buyer.
The buyer assumes all risk and liability arising from their repairs to the original product or replacement parts or arising from their installation of replacement parts. It is strongly advised that qualified professionals handle any repairs or replacements to ensure safety and proper functioning of the product. Improper installation and operation may result in injury, property damage, or voiding of warranty. The manufacturer and/or distributor shall not be held responsible for any accidents, damages, or malfunctions resulting from the buyer's installation and operation of the product. It is essential to follow all safety guidelines and recommendations provided in this manual and to seek professional assistance if unsure about the installation or operation procedures.
Customer Service
If you have any questions about ordering pool pumps, replacement parts, or other pool products, please feel free to contact XtremepowerUS using the following contact information:
Customer Service and Technical Support
Phone: (909) 628-0880
Email: customer@xtremepowerusa.com
Hours of Operation: Monday – Friday, 9AM – 4PM (CST)
