Instruction Manual for The Home Depot models including: 5268-66A 5 Light Black Island Chandelier, 5268-66A, 5 Light Black Island Chandelier, Black Island Chandelier, Island Chandelier, Chandelier
Minka-Lavery 5268-66A Bella Collina 5 Light 48 inch Coal Island Light Ceiling Light
INSTALLATION INSTRUCTIONS Item#5268-66A (New. 2023/12/08) READ AND SAVE THESE INSTRUCTIONS WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER. AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR. MOUNTING THE FIXTURE (Fig.1) Fig. 1 1. Shut off the power at the circuit breaker and remove the Set# A-020- old fixture, including the mounting hardware. -Mounting Screw *2 2. Carefully unpack your new fixture and lay out all the parts -Ground Screw on a clean area. Take care not to lose any small parts - Crossbar 6" Rod# 12" Rod# necessary for installation. 3. Determine the desired hanging height and thread rods (I & H) to coupling on fixture (J). Carefully feed wires through each rod as you assemble. Note: Remove all Outlet box thread, if installing with one 6" rod only. 4. Install swivel (E1) onto top of rod (H). A 5. Place canopy (E), metal plate (E2), support cable (F) and E C lock washer (E3) over swivel (E1), secure with hex nut B F (E4). 6. Carefully insert glass panel (J) into outer frame of fixture body (I), then secure them by pressing the clips on outer frame of fixture body (I). 7. Carefully insert glass panel (K) into inner frame of fixture body (I), then secure them by pressing the clips on inner D G H(6''x1pc) frame of fixture body (I). 8. Thread all thread into crossbar (A), then use lock washer and hex nut (C) to secure all thread into crossbar. Note: The length of all thread into crossbar may be adjusted if I(12"x3pcs) Clip necessary. 9. Take crossbar assembly and mount it to ceiling outlet box (Not included) with mounting screws (B) (Size: #8-32N*L1"). The side of crossbar marked with "GND" must face out. 10. The support cable (F) is provided to support the weight of the fixture while wiring. Align fixture to crossbar (A) and attach hook on end of support cable (F) into a slot located on crossbar (A). Carefully allow support cable (F) to support weight of fixture while wiring (Fig.1). CONNECTING THE WIRES (Fig. 2) 11. Connect the electrical wires as shown in Fig.2, making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect Fig. 2 fixture's ground wire to it. Otherwise, connect fixture's ground wire directly to crossbar (A) using green screw provided. 12. Tuck the wire connectors neatly into the outlet box. FIXTURE WIRES Black or Smooth FIXTURE WIRES White or Ribbed FIXTURE WIRES Green or Bare Copper (Ground) FINISHING THE INSTALLATION (Fig.1) 13. Raise canopy (E) over all thread and secure with nut (D) and decorative cap (G). 14. Install (5) five medium base bulbs up to 60 watts or CFL HOUSE WIRES Black (Hot) HOUSE WIRES White (Neutral) or LED equivalent (not included) in accordance with the fixture specification. -- DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE! F E H L K J HOUSE WIRES Green (Ground) 5268-66A Page 1/2 Your installation is now complete. Return power and test the fixture. Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased. Replace swivel to be loop system (Fig.3) 1. Un thread nut (E4), then remove lock washer (E3), support cable (F), strip plate (E2), swivel (E1) and rod (H) from the canopy (E). 2. Attach one loop (M) to the other loop (M) by using quick link (N). 3. Place loops (M) over canopy (E), then place metal plate (E2), support cable (F) and lock washer (E3) onto protruding all thread at top of loop (M), securing with hex nut (E4). 4. Install loops (M) onto top of rod (H). Fig.3 F F E M N M H H 5268-66A Page 2/2Microsoft: Print To PDF