MASTER ELECTRIC RADIANT WORKSHOP HEATER

Safety Information

CONSUMER: READ AND SAVE THESE INSTRUCTIONS

⚠️ CAUTION: Unplug heater when not in use. Allow unit to cool completely before moving. Always carry product by the handle when moving it.

? WARNING: Properly ventilated air must be provided. High temperature environments may cause breathing difficulties.

? WARNING: USE THIS HEATER ONLY AS DESCRIBED IN THIS MANUAL. ANY OTHER USE NOT RECOMMENDED BY THE MANUFACTURER MAY CAUSE FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.

? WARNING: FIRE OR EXPLOSION MAY OCCUR! Heater has hot arching or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored.

Factory ID: 506

[ETL LISTED]

Manufacturer: PINNACLE CLIMATE TECHNOLOGIES™

Address: Sauk Rapids, MN 56379 USA

Toll Free: (800) 641-6996

Fax: 320-251-2922

Web: www.masterindustrialproducts.com

Email: info@pinnacleclimate.com

© 2020 Pinnacle Climate Technologies, Inc. MAEA-413

NEVER LEAVE HEATER UNATTENDED WHILE CONNECTED TO A POWER SOURCE

? WARNING: RISK OF FIRE. To prevent a possible fire, do not block intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. Heater must be kept clear of all obstructions. Maintain a 1.5m / 5 ft. minimum clearance from front, sides, and rear. Heaters must be kept clean of lint, dirt, and debris. (See MAINTENANCE on Page 4).

? WARNING: RISK OF FIRE. DO NOT use heater with extension cord. Plug the heater directly into a 120VAC receptacle.

? WARNING: OVERHEATING OR FIRE MAY OCCUR. Do not place heater behind doors.

? WARNING: BURN HAZARD. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving the heater.

? WARNING: RISK OF ELECTRIC SHOCK OR INJURY. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away form the traffic area where it will not cause a tripping hazard. Do not operate any heater with a damaged cord or plug, or after heater malfunctions or has been dropped or damaged in any manner. Discard heater, or return to authorized service facility for examination and/or repair.

? WARNING: RISK OF ELECTRICAL SHOCK. Connect to properly grounded outlets only. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater. Unplug heater before performing any maintenance or when not in use. To disconnect heater, turn control to low, then remove plug from outlet.

? WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

❗ CAUTION – RISK OF ELECTRIC SHOCK: DO NOT OPEN HEATER SHELL. NO USER-SERVICEABLE PARTS INSIDE.

? WARNING: CAUTION! HOT WHILE IN OPERATION. DO NOT TOUCH. KEEP CHILDREN, ANIMALS, CLOTHING AND COMBUSTIBLES AWAY FROM HEATER.

? WARNING: Turn the electrical power off at the electrical panel board (circuit breaker or fuse box) and lock or tag the panel board door to prevent someone from turning on the power while you are working on the heater. When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

? WARNING: Read all instructions before using this heater.

• Extreme caution is necessary when any heater is used by or near children or invalids.
• This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container.
• Always locate heater on a stable and level surface.
• Do not place the heater against paperboard or low-density fiberboard surfaces.
• Avoid using an extension cord because the extension cord may overheat and cause a risk of fire.

? WARNING: RISK OF ELECTRIC SHOCK!

• ALWAYS use only the electrical power (voltage and frequency) specified on the model plate of the heater.
• ALWAYS use only three-prong, grounded outlet and extension cord.
• ALWAYS unplug the heater when not in use.
• Keep all combustible materials away from this heater.

Minimum Clearance From Combustibles

ℹ️ Look for this icon throughout the manual for helpful tips on how to use and clean your Electric Radiant Workshop Heater.

Specifications

Specifications subject to change without notice.

Features

Model: MH-410TCF-120

Figure 1 shows the Master Electric Radiant Workshop Heater. Key components include the heater head with tilt adjustment, carbon fiber heating bulbs, and a tip-over safety switch. The heater is mounted on an adjustable stand with a height adjustment knob and a stable tripod base.

Assembly

Follow these steps to assemble the heater:

1. Attach "L" Bracket to Cross Brace with Three (3) 5/8" Socket Screws.
2. Attach both Side Braces to the Cross Brace with Two (2) 5/8" Socket Screws on each.
3. Attach Heater Head to Side Braces with 5/8" Socket Screws, Two (2) on each side.
4. Finally, attach the completed Heater Head assembly to Tripod base with Two (2) 2 3/16" Socket Screws.
5. Make sure all screws are tight.

Assembly diagram illustrating the connection of the heater head to the side braces and cross brace using 5/8" socket screws, and the attachment of this assembly to the tripod base using 2 3/16" socket screws. Wing nuts are also shown.

Operation

1. Position the heater so that it stands upright on a firm, level surface and at a safe distance from wet environments and flammable objects.
2. Connect the heater to the proper electrical power.
3. Switch the power button on.

Automatic Overheat Safety Control

This heater is equipped with an overheat protection circuit. When a potential overheat temperature is reached, the system will automatically shut the heater.

Maintenance

Cleaning and Maintenance

• Before cleaning the appliance, disconnect it from the outlet and let it cool down.
• The enclosure is easy to get dirty. Wipe it often with a soft sponge. For very dirty parts, wipe with a sponge dipped in < 122°F (50°C) water and mild detergent, then dry the heater enclosure with a clean cloth. Be careful not to let the water enter the inside of the appliance.
• In order to protect the enclosure, do not splash water onto the heater, and never use a solvent like gasoline, isoamyl acetate, toluene, etc. to clean the heater.

Troubleshooting

Limited Warranty

Pinnacle Climate Technologies, Inc. warrants this heater to the original retail purchaser only, to be free from defects in material and workmanship for a period of one (1) year from the date of initial purchase. This product must be properly installed, maintained and operated in accordance with the instructions provided.

Pinnacle Climate Technologies, Inc. requires reasonable proof of your date of purchase from an authorized retailer or distributor. Therefore, you should keep your sales slip, invoice or cancelled check from the original purchase. This Limited Warranty shall be limited to the repair or replacement of parts, which prove defective under normal use and service within the warranty period, and which Pinnacle Products International, Inc. shall determine at its reasonable discretion.

This warranty does not apply to products purchased for rental use.

This Limited Warranty does not cover any failures or operating difficulties due to normal wear and tear, accident, abuse, misuse, alteration, misapplication, improper installation or improper maintenance and service by you or any third part. Failure to perform normal and routine maintenance on the heater, shipping damage, damage related to insects, birds or animals of any kind, and damage due to weather conditions are also not covered. In addition, the Limited Warranty does not cover damage to the finish, such as scratches, dents, discoloration, rust or other weather damage, after purchase.

All transportation costs for the return of damaged product or parts will be the responsibility of the purchaser. Upon receipt of damaged item, Pinnacle Climate Technologies, Inc. will examine the item and determine if defective. Pinnacle Climate Technologies, Inc. will repair or replace and return the item, freight pre-paid.

If Pinnacle Climate Technologies, Inc. finds the item to be in normal operating condition, or not defective the item will be returned freight collect. This Limited Warranty is in lieu of all other express warranties. Pinnacle Climate Technologies, Inc. disclaims all warranties for products that are purchased from sellers other than authorized dealers or distributors.

AFTER THE PERIOD OF THE ONE (1) YEAR EXPRESS WARRANTY EXPIRES, Pinnacle Climate Technologies, Inc. DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR APPLICATION. FURTHER, Pinnacle Climate Technologies, Inc. SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER OR ANY THIRD PARTY FRO ANY SPECIAL, INDIRECT, PUNITIVE INCIDENTAL, OR CONSEQUENTIAL DAMAGES. Pinnacle Climate Technologies, Inc. assumes no responsibility for any defects caused by third parties. This Limited Warranty gives the purchaser specific legal rights; a purchaser may have other rights depending upon where he or she lives. Some states do not allow the exclusion or limitation of special, incidental or consequential damages, or limitations on how long a warranty lasts, so the above exclusion and limitations may not apply to you.

Pinnacle Climate Technologies, Inc. does not authorize any person or company to assume for it any other obligation or liability in connection with the sale, installation, use, removal, return or replacement of its equipment, and no such representations are binding on Pinnacle Climate Technologies, Inc.

Always be sure to specify the model number when making any claim with Pinnacle Climate Technologies, Inc.