Instruction Manual for TASK power models including: LP42HR21NDBBK40 Lighted Power Strip, LP42HR21NDBBK40, Lighted Power Strip, Power Strip, Strip
Task Lighting & Power LP42HR21NDBBK40 42-1/2 Inch Black Lighted Power Strip Higher Light Output 4000K | Authorized Dealer
File Info : application/pdf, 4 Pages, 1.03MB
DocumentDocumentLIGHTED POWER STRIP installation instructions January 2019 Customer Service: 800-445-6404 www.TaskLighting.com Design Services & Tech Support: 866-848-9094 DesignAndSupport@TaskLighting.com Lighted Power Strip DV Series Installation Instructions for LPS WITH Built-In Power Supply General Guidelines · Power source MUST be a 20 amp branch circuit protected by a GFCI at the panel or GFCI prior to the connection at LPS. · All wiring must meet NEC® and local codes. · Light valance recommended. · Firmly insert plug straight into receptacle, applying equal pressure to both blades at the same time. Gently rock plug, if needed. Bottom of Cabinet Tool Turn power off at panel. Carefully pry open each piece with tool (provided). Insert Romex connector into knockout hole inside of back frame. Pull wires into LPS. Wiring for Combined Light and Receptacle Circuit - Non Dimmable Factory Wired RED + BLUE - SWITCH DRIVER BK BK WT WT BK GRN WT GRN DIVIDER PLATE 120V BK GRN WT BK GRN WT 12-1/2" Fixture Shown Step 1 Secure LPS to wall by screwing into wall studs or use anchors provided. Connect BLACK Romex wire to BLACK wire from receptacles and switch. Connect WHITE Romex wire to WHITE wire from receptacles and driver. Ground all GREEN wires to PEM studs inside of back frame. Step 2 When connecting 2 or more LPS fixtures, run Romex from fixture to fixture. Ground each section to the next. Step 3 To terminate last LPS, use wire nuts on ends of wires. Step 4 Snap cover in place and turn power on. Wiring for Separate Light and Receptacle Circuits Factory Wired RED + BLUE - SWITCH BK BK DRIVER WT WT DIVIDER PLATE 1201V20V for lights GRN BK GRN WT BK GRN WT 120V for 12-1/2" Fixture Shown receptacles Step 1 Secure LPS to wall by screwing into wall studs or use anchors provided. If running two circuits, one for receptacles, one for lighting, connect fixture wires to appropriate Romex wires. BLACK to BLACK. WHITE to WHITE. Ground all GREEN wires to PEM studs inside of back frame. Step 2 When connecting 2 or more LPS fixtures, run Romex from fixture to fixture. Ground each section to the next. Step 3 To terminate last LPS, use wire nuts on ends of wires. Step 4 Snap cover in place and turn power on. Customer Service: 800.445.6404 · Design Services/Technical Support: 866.848.9094 · TaskLighting.com Lighted Power Strip DV Series Wiring Diagram for 18-1/2" LPS WITH Built-In Power Supply Wiring Diagram for Combined Light & Receptacle Circuit - Non Dimmable Positive (+) Negative (-) DRIVER Back Frame Divider Plate Cover 120V Receptacle Circuit. Must be GFCI Protected. 18-1/2" Fixture Shown Wiring Diagram for Separate Light & Receptacle Circuits Positive (+) Negative (-) DRIVER Back Frame Divider Plate Cover Lighting Circuit 120V Receptacle Circuit. Must be GFCI Protected. (non dimmable) 18-1/2" Fixture Shown Customer Service: 800.445.6404 · Design Services/Technical Support: 866.848.9094 · TaskLighting.com Lighted Power Strip RM Series Installation Instructions for LPS WITHOUT Built-In Power Supply General Guidelines · Power source MUST be a 20 amp branch circuit protected by a GFCI at the panel or GFCI prior to the connection at LPS. · All wiring must meet NEC® and local codes. · Light valance recommended. · Firmly insert plug straight into receptacle, applying equal pressure to both blades at the same time. Gently rock plug, if needed. Bottom of Cabinet Tool Turn power off at panel. Carefully pry open each piece with tool (provided). Insert Romex connector into knockout hole inside of back frame. Pull wires into LPS. RED + BLACK LOW VOLTAGE DIVIDER PLATE BK WT GRN GRN 120V BK GRN WT BK GRN WT 12-1/2" Fixture Shown Positive (+) Negative (-) Back Frame 15vDC wire Cover Divider Plate 120V Circuit 18-1/2" Fixture Shown Remote Power Supply- 120V Entry Step 1 Secure LPS to wall by screwing into wall studs or use anchors provided. Connect BLACK to BLACK, WHITE to WHITE. Ground all GREEN wires to PEM studs inside of back frame. Step 2 When connecting two LPS, run Romex from fixture to fixture. Ground each section to the next. Remote Power Supply-Low Voltage Entry Step 4 Using appropriate knockout hole, pull low voltage wire from remote power supply into the low voltage space, connect BLACK wire (negative) to BLACK wire from lights and RED wire (positive) to RED wire. Step 3 To terminate last LPS, use wire nuts on ends of wires. Step 5 Snap cover in place and turn power on. Customer Service: 800.445.6404 · Design Services/Technical Support: 866.848.9094 · TaskLighting.com