Néomitis® : solutions pour le confort thermique : radiateurs - panneaux rayonnants - sèche serviettes – panneaux acier – gestion d’énergie
Instructions for NEOMITIS models including: ER1C1, Myneo Stat 1 Channel Radio Receiver, ER1C1 Myneo Stat 1 Channel Radio Receiver, Stat 1 Channel Radio Receiver, 1 Channel Radio Receiver, Radio Receiver, Receiver
1 channel radio receiver - Neomitis
Instruction manuals - Neomitis
File Info : application/pdf, 4 Pages, 2.34MB
DocumentDocumentER1C1
INSTRUCTIONS
FOR INSTALLING AND USING
IZ Fixed green Fixed red Fixed orange Green blinking 'Z blinking
K ,ZZ ,ZZKE DZKE Manual override OFF
WZZ
PACK CONTAINS
MYNEO STAT 1 CHANNEL RADIO RECEIVER
OVERVIEW
tZZZZZZZZ This wall-mounted receiver has been specially designed to be associated with your inZZZZZZZZZ ZZZ/ZZZZZZZ ZZZZZ
TABLE OF CONTENTS
K 1 ^Z 1 WZ 1 /Z 1
Receiver wiring ........................................................................................................................... 1 Z Z.................................................................................................................... 2
K 4 Z& Z ................................................................. 4 D Z Z............................................................................................. 4
dZZZ 4 / Z Z .............................................................................................................. 4 Z Z ....................................................................................................................... 4
dZ 4 WZZ 4
DIAGRAM
x1
Receiver
x1
x2
x2
Link
Screws
Small
screws
INSTALLATION
x2
Screw anchors
RECEIVER WIRING
/ZZZZZ ZZZZ/ZZZZ ZZZZZZZZZ ZZZ Z
· Housing opening
1- Unscrew the screw located under the front housing.
2- Separate the wall base from the front housing.
The capacity of all terminals: 1 mm² to 1.5 mm². Use preferably 1.5 mm² conductors ZZZ
Cable stripping:
/Z
Z
> sZ of the radio ZZ
Z Z&ZZ
IZ Green blinking Orange blinking Fixed green Fast green blinking Red blinking Fixed red 'Z blinking
ER1C1 NEO EN CP V01 20 04 2022
>
2µ3100V(1~)A/5m0Hazx.
sZZ
LN
Z
Z
&ZZZ
K Pairing in progress Time out Connected Receiving a RF command Canceling pairing Unpaired
WZZ
Terminals
Receiver front cover
Receiver front cover
Proceed to the wiring in the following order:
DZ
Terminals Z
1
sZZ
2
sZZZ
3
>Z>
4
EZE
5
>>WZ
6
EEWZ
Terminals
1
/Z
Link supplied
Z
Z
230V~/50Hz µ10(1)A max.
LN
NEOMITIS LIMITED ER1C1 1 channel receiver
230V~/50Hz 10 (1)A max.
LORA - 869.85Mhz
3134 01 00001 YYWW VV
LN
NEOMITIS LIMITED - 16 Great Queen Street, Covent
Garden, London WC2B 5AH - UK
IMHOTEP CREATION ZI Montplaisir - 258 rue du
Champs de course 38780 Pont-Evêque - France
NEOMITIS LIMITED ER1C1 1 channel receiver
230V~/50Hz 10 (1)A max.
LORA - 869.85Mhz
3134 01 00001 YYWW VV
LN
NEOMITIS LIMITED - 16 Great Queen Street, Covent
Garden, London WC2B 5AH - UK
IMHOTEP CREATION ZI Montplaisir - 258 rue du
Champs de course 38780 Pont-Evêque - France
56
N WZ 230V
L E
L
/Z
ZZZZZZZ
Terminals Z
1-2 Voltage-free contact
3
EZ
4
EZ
5
>>WZ
6
EEWZ
230V~/50Hz µ10(1)A max.
LN
Shunt
> Z ZZ
Boiler terminals
Z
NEOMITIS LIMITED ER1C1 1 channel receiver
230V~/50Hz 10 (1)A max.
LORA - 869.85Mhz
3134 01 00001 YYWW VV
LN
NEOMITIS LIMITED - 16 Great Queen Street, Covent
Garden, London WC2B 5AH - UK
IMHOTEP CREATION ZI Montplaisir - 258 rue du
Champs de course 38780 Pont-Evêque - France
56
/Z
230V~/50Hz µ10(1)A max.
LN
12
N WZ L 230V
RECEIVER INSTALLATION
Z Z Z Z ZZ Z Z
ZZZ
^ Z Z /W cessed box with a standard diameter of 60
ZZZ which it must control.
tZZon its wall base
ZZZ
ZZZ
ZZZ
30cm
min
/ Z
closure piece is provided.
/Zd ZZZZZ KEKd^dhWd,Z/sZKE,Kd^hZ&
^Z
ZZ / Z Z ZZ Z ZZZZZZ box.
KZ Under the housing
ZZ On the back of the case in a ZZ
ZZZZZ
/ZdZZZZZ dZZZ Z
Terminals Z
1
Switched phase output to the load
2-3
Link between terminals 2 and 3 (live output 3 Z
4
EZZZ
5
>>WZ
6
EEWZ
> between termi-
ZZ
1- Remove the cable clamp present on the receiver.
2- pass through the cable of the device
to be connected.
2
3-D ZZZ 4- Put the sealing cap in the dedicated
device.
area.
Z
1- WZZZ the wall base to the wall.
2- /ZZ
back of the wall base.
5-Z
6- hZZ mount the receiver on the recessed
box.
3- Secure the wall base with the two screws and plugs provided.
4- hZZ mount the receiver on the recessed
box.
Z
1- Put the cables to be connected in the area provided for this purpose
2- DZZ(see .
hZ
4- pass through the cable of the device
to be connected.
5- Put the sealing cap in the dedicated area.
3- hZZZ receiver on the recessed box.
^Z
ZZZZZ
6- WZZ
7- hZZ mount the receiver on the recessed
box.
Note: /ZZZ
ZZ
1- Replace the product cover.
2- Lock the cover the screw
below.
ZZ d ZZZZZZZZ
ZZ
Z Under the housing
Z
On the back of the case ZZZ
ZZ
On the side of the housing
with the cable guide (not ZZ ZZ controlled
OPERATING
RF PAIRING BETWEEN THE THERMOSTAT AND THE RECEIVER
The receiver and the thermostat are not linked at the factory. For the transmission to ZZZdZ manual of the thermostat to be linked with you to carry out the learning stage. This ZZZZZ
ZZZZ
This wall-mounted receiver has been specially designed to be connected directly to your smart thermostat. dZZZZZZZZZ
3
1- KZZ Z
/ZZ
for about 5 seconds to stop the process.
- Move the thermostat out of the disturbed area.
DZ
> ZZZ Z
Z ZZZZ Z.
/ Z Z Z
2-W Z Z ZZ ZWZZ your thermostat's user manual and let
ZZZ your receiver is fully connected.
3-t receiver is connected to the intelligent
thermostat.
WZ
sZ
W Z Z Z Z manual.
s <ZZZ-
out releasing it:
ZZZZ ZZZ
Zthe receiver erases the radio asZZ Z Z Z Z Z
ZZZZzZZ
ZZ Z Z Z Z Z (please ZZZZ.
MANUAL TEST OF THE RECEIVER OUTPUT
You can manually test the receiver and tempo-
ZZZ Z Z d Z Z will be turned on.
dZ ZZZZZZ This manual command will be canceled at the next order received by the receiver.
&ZZZ
TECHNICAL SPECIFICATIONS
Ds Hz.
W ZZ Z Z 230V.
- Power in standby mode: <0.5W.
ZZ DZZZd ^///P44 wall mounted and
/WyZ. WZZ - Rated impulse voltage: 4000V.
> ZZ&ZZZ Z ZZD 62.5KHz.
- Radio power: <15dbm.
- Receiver category: 3.
Dimensions: ZZZ
Z KZZ ^ZZ , ZZ-
D /D,KdW Z ZZZZ /Z EZ > Z ZZ Z /D,KdW Z EZ > are part of Axenco Group.
^h<ZZZZ,EKD/d/^> ZZZ ZZZZEZZZ,^ZZEZ
d Z h< Z Z ZZ ZZZZ
^hZZZZ,/D,KdWZ ZZZ hh
d Z h Z Z ZZ ZZZZZ
dZZZ /^Ks
TROUBLESHOOTING
IN CASE OF POWER FAILURE
d Z Z Z Z Z ZZtZZZZZZ
DIAGNOSIS SUPPORT
Z
- Check the level of radio transmission
dZZ EZ Z Z
circuit breaker or the fuse in the power
supply circuit. Z -
tween the thermostat and the receiver
Z Z Z Z/Z sure that the radio transmission has not Z Z closer to the receiver. Z by an external heat source.
from working properly.
d Z Z Z
dZ - Contact your installer.
Z ZZZZ-
ZZZZ
d
procedure Z.
- Contact your installer.
dZ Z& mission
d ZZZZZZ
Z ZZ Z (see
d Z Z Z Z Z Z.
Z
d Z Z -
Z
The symbol ZZ indicates that you must dispose of it at the
end of its useful life at a special recycling
ZZZth/Z ZZZZ ZdZZZZ Recycling products enables us to protect the environment and to use less natural re-
sources.
PRODUCT CODE
dZZZZZ code and reference:
Z ER1C1
Z Myneo stat 1 channel radio receiver for connected thermostat
Z
www.neomitis.com
ZZZZZZ
NEOMITIS®>/D/d'Y^Z'>ZZt,hE/d</E'KD ZtEZ
d&ZZZ
4