User Guide for SYSGRATION models including: UPC-N101, 10.1 Inch 15.6 Inch and 21.5 Inch Universal Panel Computer
15.6" UPC-N156 - Automotive & Mobile Division - AMD SYSGRATION
1. The appropriate cut out on the panel or wall, refer to this table for appropriate cutout dimension for di˜erent UPC sizes. 2. Insert the UPC into the cutout area.
VESA Mounting UPC UPC-N101 can be mounted to a VESA 75 x 75 and UPC-N156/N215 can be mounted to a VESA 100 X 100 mounting system. · Rear view with holes (M4-depth 5 mm) for VESA 75/100 Mounting. · UPC has to be installed and operated only by trained personnel. Note · Please make sure the VESA Plate supporting weight is appropriate for different sizes and weight of UPC. 3. Fasten the expansion module into the mounting bracket using M3 x 5 mm screw with torque maximum 4 kgf-cm. 4. Organize USB cable behind panel computer to neatly attached (using the clamp cable) to the back of your panel computer and then connect the USB cable to I/O Port (USB). 5. Installation complete. 1 2 3 Use proper mounting equipment to prevent serious injury. Caution Expansion Module Installation 5 (optional) 1. Secure module mounting bracket to the UPC system using M3 x 5mm screw with torque maximum 4 kgf-cm. 2. Pass the cable into cutting hole on the mounting bracket and then secure expansion module to the mounting bracket. 6 4 7 Setup Procedures System Power On 1. For the UPC-N101/ UPC-N156/ UPC-N215 model, connecting the system to a DC power source or external power supply via DC in Jack. 2. Hold power cords by the plugs end only. 3. After DC input, the system will be activated automatically. UPC needs to be installed and operated by trained Caution personnel. Operating the touchscreen Tapping Double tapping Tapping and holding Swiping Dragging Pinching To avoid damage, do not tap the screen with sharp object. Note For more information about this or other Sysgration products, please visit our website at http://www.sysgration.com For technical support and service, please visit our support website at http://www.sysgration.com This manual is for UPC-N101/N156/N215. Manufacturer Sysgration Co., Ltd. 6Fl., No.1, Sec. 1, Tiding Blvd., Neihu Dist., Taipei City, 11494, Taiwan, R.O.C. TEL: +886-2-2790-0088 8 9 UPC-N101/N156/N215 10.1"/15.6"/21.5" Universal Panel Computer Edition 1 Last updated: 15-Jun-2021 600-2200017-001 Check Items UPC-N101/N156/N215 Packet of mounting kits DC power converting cable Quick start guide Packet of cable Clamps (only available on 15.6" / 21.5") If any of these items are missing or damaged, contact Caution your distributor or sales representative immediately. Product Dimensions UPC-N101 dimension 4.5 257.2 266.2 184.8 Product Overview 175.8 4.5 248.5 4.5 40 6 UPC-N156 dimension 4.5 390.2 399.2 4.5 A B CD E F G H I A. DC Power Input B. 10/100/1000 GbE C. 2 x USB 3.0 ports type A D. USB 3.0 Type-C DRP E. Micro SD Card Slot F. HDMI output 2.0 G. RS232 Serial Port H. Reset tact-switch push I. Audio Line Out 1 VESA Hole M4 depth=5mm 75 185 2 38 75 39.9 VESA Hole M4 depth=5mm 100 330 3 80.7 4.5 40 6 UPC-N215 dimension 4.50 534.64 543.64 4.5 239.5 4.5 VESA Hole M4 depth=5mm 100 335.11 4.50 40 6 4.50 326.11 4.50 Panel Mounting UPC 1. The appropriate cut out on the panel or wall, refer to this table for appropriate cutout dimension for different UPC sizes. Type UPC-N101 UPC-N156 UPC-N215 Suggested cut out size (w x h) 259.20 x 177.80 mm 392.20 x 241.50 mm 536.60 x 328.10 mm 2. Insert the UPC into the cutout area. 3. Place the mounting bracket to the UPC and fasten it using M3 x 6 mm screw (torque max 4 kgf-cm), tighten each mounting bracket on every side until each of it is firmly tightened. 4. Fasten the M4 x 20 mm screw to fix the bracket to the panel. 5. Installation complete. 1 2 3 100 117.56 100 49.3 4 400 Specifications and dimensions are subject to change without notice 4 75 5 5Adobe PDF library 15.00 Adobe Illustrator 24.3 (Windows)