Instructions for Tell models including: LE2000 Electronic Keypad Lock, LE2000, Electronic Keypad Lock, Keypad Lock, Lock
SYSTEM SIGNALS Use Cases Sound Light Correct user code entered to unlock door 2 short beeps 2 short green flashes Lock auto-locks 1 long beep 1 long red flash
Product Templates| Tell Manufacturing
PROGRAMMING INSTRUCTIONS FOR LE2000 ELECTRONIC KEYPAD LOCK Featuring SmartKey TechnologyTM with an SC1 Keyway REFERENCE GUIDE AT A GLANCE Exterior Lever Interior Lever (cover removed) Tell Button Keypad Program Button 9V Battery Turnpiece SC1 Keyway SmartKey Tool Hole BEFORE BEGINNING ANY PROGRAMMING: ENSURE THAT THE LOCK IS UNLOCKED AND THE DOOR IS KEPT OPEN. There are two ways to enter the programming mode. First, by pushing the Program Button (shown above in the diagram). A second method is by creating a Programming Code, which allows you to enter the programming mode if you don't have access to the interior of the lock. Please follow the instructions in the table below to begin programming. *NOTE: Programming Codes cannot be the same as User Code. If you are using a Programming Code, the Program Button will be disabled except to factory reset the lock. Move swiftly during programming. If no digit is pressed for 10 seconds, the system will time out and you will need to restart the procedure. TASK Step 1 Step 2 Step 3 Step 4 Step 5 Step6 CREATE A PROGRAMMING CODE Press Program Button* ADD USER CODE ADD ONE-TIME CODE Listen for 2 beeps DELETE USER CODE DELETE ALL Enter Program Press USER CODES Code Button CHANGE AUTO- or or LOCK DURATION Press Program Listen for MUTE/UNMUTE Button* LOCK 2 beeps ENABLE/ DISABLE USER CODE ENABLE/ DISABLE TURNPIECE Press Program FACTORY RESET Button Long beep (approx 30 sec) Press 3 then Press Button Enter 4 to 8 Digit Code and Press Button Press 1 then Enter 4 to 8 Press Button Digit Code Press 7 then Enter 4 to 8 Press Button Digit Code Press 2 then Press Button Enter Code You Wish to Delete and Press Button Press 4 then Enter 9-9-9-9-9-9 Press Button Press Button Press 8, Green Flash Press Button, Enter Delay Time (1-99 seconds) Press 5, Green Flash Press Button Re-Enter 4 to 8 Digit Code and Press Button Press Button Press Button Re-Enter Code You Wish to Delete and Press Button Re-Enter 9-9-9-9-9-9 Press Button Press Button Green Flash- Success, Red-Failed Attempt Green Flash-Success, Red-Failed Attempt Green Flash-Success, Red-Failed Attempt Green Flash-Success, Red-Failed Attempt Green Flash-Success, Red-Failed Attempt Green Flash-Success, Red-Failed Attempt Green Flash- Success, Red-Failed Attempt -- Press 6 Press Button Green Flash- Success, Red-Failed Attempt -- Press 9 Press Button Green Flash- Success, Red-Failed Attempt -- Press and Release Program -- -- -- Button Again SYSTEM SIGNALS Use Cases Correct user code entered to unlock door Lock auto-locks Turnpiece rotated to unlock position Turnpiece rotated to locked position Low battery alarm 3 incorrect user codes entered Entering factory reset mode after Program Button is pressed and held for 30 seconds. Entering programming mode after pressing and releasing Program Button Successful programming Unsuccessful programming Sound 2 short beeps 1 long beep 2 short beeps 1 long beep 10 short beeps 15 long beeps 1 long beep 2 beeps 1 long beep 3 short beeps Light 2 short green flashes 1 long red flash None None 10 short red flashes 15 long red flashes None None 1 long green flash 3 short red flashes TROUBLESHOOTING PROBLEM SOLUTION Keypad is not responding. Desired user code cannot be programmed. Key cannot be removed when unlocked. Emergency egress function Check battery. For security reasons, the first 4 digits of each user code must be unique. For example, you cannot program a user code 4-8-1-5-1 as well as a user code 4-8-1-5-2. This is a feature to ensure the door is always locked and the key is removed (store room function). To remove the key, return the key to vertical position to remove. This lock has an emergency egress function which allows you to exit by turning the lever on the inside, regardless of whether it is in Auto-lock or Passage mode.Adobe PDF Library 17.0 Adobe InDesign 19.3 (Macintosh)