User Guide for Cel-Fi models including: G32-2-4-5-12-13, G32-1-3-5-7-8-20, GO plus RV Trucker Kit Smart Signal Booster, GO plus RV Trucker Kit, RV Kit, Trucker Kit, Trucker Kit Smart Signal Booster, Smart Signal Booster, Smart Booster, Signal Booster, Booster
Cel-Fi GO RV/Trucker Kit - Waveform
Specifications: Frequency Support Multiple variations of the product are available with different frequency support. Model: G32-2/4/5/12/13 BAND 2 4 NAME 1900 PCS AWS1 DOWNLINK 1930 1990 2110 2155 UPLINK 1850 1910 1710 1755 5 850 869 894 824 849 12 700 a 729 746 699 716 13 700 c 746 756 Gain Up to 100 dB system gain Model: BAND NAME DOWNLINK G32-1/3/5/7/8/20 1 2100 2110 2170 777 787 UPLINK 1920 1980 3 1800+ 1805 1880 1710 1785 5 850 869 894 824 849 7 2600 2620 2690 2500 2570 8 900 925 960 880 915 20 800 DD 791 821 832 862 Gain Up to 100 dB system gain Dimensions LENGTH WIDTH HEIGHT 272.5 mm 96.5 mm 43.5 mm WEIGHT 850 g Power (max) DOWNLINK TX 10 dBm/5 MHz (16 dBm per band) UPLINK TX 24 dBm per band Bluetooth (LE Ver 4.2) FREQUENCY 2042 2480 MHz Environmental Operating Temp: 0 - 65°C POWER 0 dBm Relative Humidity: 95% Antenna Connectors SMA-Female 3GPP TS 25.143 Rel.10 (All variants) 3GPP TS 36.143 Rel.10 RoHS 2 BQB (Bluetooth) NEMA-4 (G32-2/4/5/12/13 FCC variants only) ISED UL 62368-1:2014 CSA C22.2#62368-1 UL 50E, UL 60950-22 CSA C22.2#60950-22 (G32-1/3/5/7/8/20 IEC 62368-1:2014 variants only) EN 301 489-1 v2.1.1 EN 301 908-1 v11.1.1 EN 301 908 v11.1.2 EN 301 489-17 v3.1.1 EN 301 908 v11.1.2 EN 301 489-50 v2.2.0 EN 300 328 v2.1.1 EN 62311 (2008) Regulation (EC) 1275/2008 (Standby and Off mode) Regulation (EC) 278/2009 (External Power Supply) User Interface Cel-Fi GO+ Smart Signal Booster features an LED on the top face to indicate the unit's state: LED MEANING Solid GREEN The unit is working properly and boosting properly. Blinking GREEN Unit is scanning for networks to boost. Blinking RED The unit is in an error condition. Use the Cel-Fi WAVE app to check the error code meaning and remedy. Solid RED The unit has a hardware error and is not booting up normally. NOTE: In mobile usage, it is normal for the Cel-Fi GO+ Smart Signal Booster to fluctuate between scanning and boosting. The Cel-Fi GO+ Smart Signal Booster automatically adjusts its boost behavior based on available signal. Troubleshooting ISSUE MEANING ACTION Continual Blinking GREEN Unit is · Make sure both antennas are connected operational, but properly and are appropriate for the desired not attaching to a frequencies to boost. network to boost. · Make sure the selected operator to relay is available at your location. This can be checked with the Cel-Fi WAVE application. If the service is not available, it cannot be boosted. Solid Unit is not RED LED operational. · Unplug and reinsert power. · If restart has no effect, contact vendor for remedy. Antenna and Mount Options: Review the latest authorized antennas at Cel-Fi Trucker Antenna A21-V31-100 Cel-Fi Mobile Server Antenna A41-V30-100 Cel-Fi GO+ Smart Signal Booster Cel-Fi GO+ RV/Trucker Kit Quick Start Guide Smart Signal Booster TM Basic Functionality The Cel-Fi GO+ Smart Signal Booster Smart Signal Booster is designed to improve cellular coverage in a building, remote area, or vehicle. Cel-Fi GO+ connects to an external Donor Antenna to draw in a cellular signal from the macro network, and redistribute signal via the Server Antenna. Cel-Fi WAVE App The Cel-Fi WAVE app provides a User Interface to Cel-Fi systems. The app's dashboard shows the system "Boost" value that is a numeric representation mapped to the amount of signal gain the system is providing. Higher is better, with nine (9) being the highest value. Cel-Fi WAVE functions as the registration and management application that allows users to setup antenna, modes, and carriers, and is available through either the Google Play Store or Apple App Store. band to boost. · Cel-Fi WAVE app. · Change carrier · Change mode (Stationary or Mobile) NEMA 4 Rating The Cel-Fi GO+ is NEMA 4 rated, and can be used both indoors and outdoors. The NEMA 4 rating provides the following advantages: · A degree of protection against ingress of solid foreign objects (falling dirt and windblown dust) · A degree of protection from the ingress of water (rain, sleet, snow, splashing water, and hose directed water) · Equipment will be undamaged by the external formation of ice on the enclosure For more information, visit: Cel-Fi GO+ Smart Signal Booster Installation Before You Begin Cel-Fi GO+ Smart Signal Booster has a Donor Antenna Port and a Server Antenna Port. They are marked on the device with icons (see illustration). It is critical that the Donor and Server antennas are connected to the correct port. IMPORTANT: Best to make sure all cable lengths support the intended mounting location BEFORE permanent mounting. SERVER DONOR 1 Install Donor Antenna 2 Install Server Antenna 3 Mount Cel-Fi GO+ 4 Connect Donor & Server Antennas 5 An AC or 12V Power to the Cel-Fi GO+ Source 1 2 35 4 6 Activate & Setup with Cel-Fi WAVE Point & Optimize Antenna For mobile (non-stationary) applications, Mobile Mode should be selected in the Cel-Fi WAVE A p p . Install Tips for Donor Antenna · Install antenna at least 12 inches from any other antennas for best performance · Antenna should be free of obstructions · Antenna should be away from windows (including sunroof or other openings) · Install 8 inches away from any people · For best performance make sure there is 50 cm of metal around the base of the antenna Install Tips for Server Antenna · For best results, install Donor and Server Antennas such that there is substantial material between the antennas. This will create isolation and allow the system to perform at higher gain without oscillation or feedback · Keep Donor and Service Antennas separated/isolated from each other for best performance · Do not use cable splitters for Donor Antennas · If using directional antennas, do not point them at each other · possible · Follow the installation instructions for your chosen antennas · The power supply is not NEMA 4 rated Tips for Mobile Mounting: · Location should have airflow (for cooling) and be secure from contact with external objects · Make sure the unit is within cable range of the 12V power supply on your vehicle Change Between Modes and Carriers IMPORTANT: Cel-Fi GO+ Smart Signal Booster ships with a mode and operator selected, but some versions can be changed via Cel-Fi WAVE. It is critical that the booster's mode match the application, for both regulatory andperformance reasons. If the booster is in motion, it should be set to Mobile mode. If the booster is stationary, it should be set to Stationary mode. Change Modes Between Mobile (65/70 dB) or Stationary (100 dB) 1. Open Cel-Fi WAVE application 2. Go to settings tab 3. Select Booster Setting 4. Switch between mobile and stationary Change Carrier /Operator 1. Open Cel-Fi WAVE application 2. Go to settings tab 3. Select Operator 4. Switch between mobile network operators Cel-Fi GO+ Smart Signal Booster This guide has been modified from its original form to better align with the Cel-Fi GO+ RV/Trucker Kit.Adobe PDF Library 15.0 Adobe Illustrator(R) 24.0