CSR Login Page
Manual-Hub.com - Free English product PDF Documents!
Instruction Manual for duraflame models including: DFI-550 Black Infrared Freestanding Electric Fireplace, DFI-550, Black Infrared Freestanding Electric Fireplace, Freestanding Electric Fireplace, Electric Fireplace, Fireplace
DURAFLAME DFI-550-41 (01) PDF MANUAL - MANUAL-HUB.COM
File Info : application/pdf, 4 Pages, 1.69MB
DocumentDocumentMODELS: DFI-550-41, DFI-550-42, DFI-550-43,DFI-550-44,DFI-550-45,DFI-550-47 Go to tsicustomerservice.com for product warranty registration ASSEMBLY INSTRUCTIONS 1 2 3 MOUNTING THE LEGS 1) Align the 2 mounting tabs into the bracket. 2) Slide the legs outward to lock in place. When locked in position the screw hole from step 3 will be aligned. 3) Fasten the legs to the base using the included screws,1 per leg. OPERATING INSTRUCTIONS Control Panel Location Remote Control Control Panel OPERATING INSTRUCTIONS PRODUCT SPECIFICATIONS -- POWER 1. The power button supplies power to all of the fireplace functions. The power button will put the insert in a standby mode. This will turn off all functions at once, but will hold the settings in the memory. By pressing the Power button again, the unit will turn on with the retained settings. 2. With the power on, press and hold the Power button on the control panel for 10 seconds to disable or re-enable the heater function. Once disabled or reenabled, the ember bed lights will flash multiple times. -- FLAME 1. There are 5 brightness levels that can be selected and OFF (00) setting. 2. Settings F5 - F1 decrease in brightness. Default is F5. VOLTAGE AMPS WATTS 120 VAC, 60 Hz 12.5 Amps 1500 Watts For Customer Service: tsicustomerservice.com (+1) 888-674-7517 8:30 a.m.-5:30 p.m., EST, Monday-Friday -- HEATER Note: When first running the heater there may be an odor. This is normal as the heater has a 1. The stove contains a fan forced infrared element heater. surface coating on the internal parts. For the 2. The default temperature is 72°F. 3. The thermostat setting range is 62°F - 82°F (17°C - 27°C) or continuously ON or OFF(00). 4. The thermostat is adjustable by 2°F or 1°C increments by pressing the HEATER button first several hours of operation, the coating reacts with the internal parts to permanently on the control panel. protect them. The odor is safe; if you are 5. To change between °F and °C press and hold the HEATER button on the control panel for 3 seconds. sensitive to the odor, it is recommended to run the heater in a well-ventilated area until -- TIMER the odor dissipates. 1. Pressing the timer button will cycle through the timer settings: 30 minutes, 1 Hour, 2H, 3H, 4H, 5H, 6H, 7H, 8H, 9H and off (00). Warning: This is an unvented, electric appliance. DO NOT attempt to burn wood or manufactured firelogs in or on this appliance or grate. Manufactured and distributed by Twin-Star International, Inc., under license from Duraflame, Inc. duraflame, the flame symbol and logo are registered trademarks of Duraflame, Inc. Twin-Star International, Inc. Delray Beach, FL 33445 Made in China Made in China © 2018,Twin-Star International,Inc. A657 https://manual-hub.com/ IMPORTANT INSTRUCTIONS When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons including the following: 1. Read all instructions before using this appliance. 11. To disconnect this appliance, turn controls to the off position, then remove 2. This appliance is hot when in use. To avoid burns, do not let bare skin touch hot plug from outlet. surfaces. If provided, use handles when moving this appliance. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of this appliance and keep away from the sides and the rear. 12. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the appliance. WARNING: In order to avoid overheating, do not cover the heater. 3. CAUTION: Never leave the heater operating unattended. Extreme caution is necessary if unsupervised children or invalids are nearby. 13. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where opening may become blocked. 4. The appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. 5. Always unplug this appliance when not in use. 6. Do not operate any heater with a damaged cord or plug or after the appliance malfunctions, or if it has been dropped or damaged in any manner. 14. This appliance has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored. This stove should not be used as a drying rack for clothing. Christmas stockings or decorations should not be hung in the area of it. 15. Use this appliance only as described in the manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons. 7. If the supply cord is damaged, it must be replaced by the manufacturer, its 16. This product is equipped with a polarized plug (one blade is wider service agent or similarly qualified persons in order to avoid a hazard. than the other blade). To reduce the risk of electrical shock, this plug will fit into a polarized outlet only one way. This is a safety feature. If 8. Do not use outdoors. you are unable to insert the plug into the electrical outlet, try reversing the plug. If the plug still does not fit, contact a qualified electrician. 9. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate this appliance where it may fall into a bathtub or other water container. 10. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over. Battery Replacement AAA 1.5V AAA 1.5V Note: Battery disposal Please always dispose of batteries at a suitable recycling point. 1. The battery compartment is located on the back end of the remote control. 2. Press and slide the battery door open and remove the old battery. 3. Insert 2 AAA batteries, checking that the + and - sides of the battery match inside the battery compartment. 4. Replace the battery compartment door. Caution: · For best results, use 2pcs AAA alkaline batteries. · Install only new batteries of the same type in your product. · Failure to insert batteries in the correct polarity, as indicated in the battery compartment, may shorten the life of the batteries or cause batteries to leak. · Do not mix old and new batteries. · Do not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel Cadmium) or (Nickel Metal Hydride) batteries. · Danger of explosion if battery is incorrectly replaced. · Do not ingest batteries. Batteries should be recycled or disposed of as per state and local guidelines. DISPOSAL OF USED BATTERIES Battery may contain hazardous substances which could endanger the enviroment and human health. Used batteries shall not be treated as municipal waste, but left at the appropriate collection point for recycling. For more information about collection and recycling of used batteries, please contact your local municipality or waste disposal service. 1-YEAR LIMITED WARRANTY The manufacturer warrants that your new Electric Stove is free from manufacturing and material defects for a period of one year from date of puchase, subject to the following conditions and limitations. 1. Install and operate this Electric Stove in accordance with the installation and operating instructions furnished with the product at all times. Any unauthorized repair, alteration, willful abuse, accident, or misuse of the product shall nullify this warranty. 2. This warranty is non-transferable, and is made to the original owner, provided that the purchase was made through an authorized supplier of the product. 3. The warranty is limited to the repair or replacement of part(s) found to be defective in material or workmanship, provided that such part(s) have been subjected to normal conditions of use and service, after said defect is confirmed by the manufacturer's inspection. 4. The manufacturer may, at its discretion, fully discharge all obligations with respect to this warranty by refunding the wholesale price of the defective part(s). 5. Any installation, labor, construction, transportation, or other related costs/expenses arising from defective part(s), repair, replacement, or otherwise of same, will not be covered by this warranty, nor shall the manufacturer assume responsibility for same. 6. The owner/user assumes all other risks, if any, including the risk of any direct, indirect or consequential loss or damage arising out of the use, or inability to use the product, except as provided by law. 7. All other warranties expressed or implied with respect to the product, its components and accessories, or any obligations/liabilities on the part of the manu facturer are hereby expressly excluded. 8. The manufacturer neither assumes, nor authorizes any third party to assume on its behalf, any other liabilities with respect to the sale of the product. 9. The warranties as outlined within this document do not apply to non accessories used in conjunction with the installation of this product. 10.This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This warranty is void if: a. The fireplace is subjected to prolonged periods of dampness or condensation. b. Any unauthorized alteration, willful abuse, accident, or misuse of the product. SAVE THESE c. You do not have the original receipt of purchase. IF WARRANTY SERVICE IS NEEDED Contact the manufacturer by calling customer service department at 1-888-674-7517, 7 days a week 24 hours a day at our toll-free help line. Our Consumer Service department is available Monday Friday 8:30 am 5:30 pm EST. Make sure you have your warranty, your sales receipt, location of purchase and the model/serial number of your product. INSTRUCTIONS A657 https://manual-hub.com/ MODELS: DFI-550-41, DFI-550-42, DFI-550-43,DFI-550-44,DFI-550-45,DFI-550-47 TROUBLESHOOTING GUIDE Problem 1. No power, buttons do not light up. 2. Stove does not turn on manually. 3. Flames are not moving Root Cause 1. Power cord was not plugged into the outlet. 2a. No incoming power from the electrical wall socket or buttons. 2b. Improper operation. 2c. Defective button 3a. Defective spinner motor 3b. Spinner detached from the motor Corrective Action 1. Check that unit is plugged directly into a standard 120 volt outlet. 2a. Check circuit breakers and move unit to another outlet. 2b. Manually press main power button from front of unit. 2c. Replace button 3a. Replace spinner motor 3b. Remove the back panel and check to see if "spinner" is correctly mounted to the motor. 4. Flames are not visible 5. Flames are not bright 6. Heater is not turning off 7. Heater is not turning on 8. Not producing enough heat 9. Unit blows cool or cold air 10. Noise with heater on 11. Noise with flames on and heater off 12. Power cord gets warm 4. Burnt out light bulb 5a. Normal operation 5b. Defective dimmer button 6. Defective Thermostat Button 7a. Improper operation 7b. Defective button 7c. Defective heater blower motor 8a. Power strip/surge protector/ extension cord being used 8b. Location of unit 9. Defective heater blower motor 10a. Dirty heater blower motor 10b. Defective heater blower motor 11a. Defective flame generator drive motor. 11b. Dented back panel 11c. Warped spinner shaft 12. Normal operation 13. Is it safe to place unit on carpet? 13. Product Inquriy 14. How many square feet will my unit warm up? 14. Product Inquriy 15. Heater doesn't work, but Power and Heater buttons are in the "ON" position and thermostat is set on the highest level. 15. The thermal protector has tripped. 4. Replace 40 watt candelabra bulb 5a. Turn brightness dimmer knob until desired brightness is achieved. 5b. Replace dimmer button 6. Replace Thermostat Button 7a. Manually press main power button on front of unit. 7b. Replace button 7c. Replace heater blower motor. 8a. Plug unit directly into the wall. 8b. Make sure unit is located on an interior wall. 9. Replace heater blower motor 10a. Gently vacuum heater blower vents. 10b. Replace heater blower motor 11a. Replace flame generator drive motor. 11b. Refer to TSI customer service 11c. Refer to TSI customer service 12. Check your heater cord and plug connections. Faulty wall outlet connections or loose plugs can cause the outlet or plug to overheat. Be sure the plug fits tight in the outlet. Heaters draw more current than small appliances, overheating of the outlet may occur even if it has not occurred with the use of other appliances. During use check frequently to determine if your plug outlet or faceplate is HOT! If so, discontinue use of the heater and have a qualified electrician check and/or replace the faulty outlet(s). 13. It is safe to place unit on carpet but make sure any flammable items are at least 3 feet away from front and sides of the unit. 14. Provides supplemental heat up to 1000 square feet 15. Turn all buttons to the "OFF" position and unplug the unit from the wall outlet for 5 minutes. After 5 minutes, plug the unit back into wall outlet and operate as normal. https://manual-hub.com/ A657 EXPLODED VIEW Part Part Name 1 Control panel 2 Control panel PCBA 3 Legs 4 Emberbed 5 Flame Generator Drive Motor 6 Main PCBA 7 Remote control 8 Display PCBA Part Number Y18-S260-P85 Y18-S260-P32 SL-550-41, SL-550-42, SL-550-43, SL-550-44, SL-550-45, SL-550-47 Y15-S45-P02 P10-Q-S Y18-S260-P15 P136 Y18-S260-P79 CARE AND MAINTENANCE · Clean the trim using a soft cloth, slightly dampened with citrus oil based product and buff with a clean soft cloth. · DO NOT use brass polish or household cleaners as these products will damage the metal trim. Citrus oil based products can be obtained at supermarkets or hardware stores. · WARNING: Electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electrical shock and injury to persons. · Warning: Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electrical shock or personal injury. FCC/IC INFORMATION Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and the receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003. https://manual-hub.com/ A657