Need Support? | Support
Installation Guide for Hid Global models including: MOD001, SL6-MOD001, SL6MOD001, MOD001 BEEKS BLE Module, BEEKS BLE Module
HID Global Corporation MOD001 BEEKS BLE Module SL6-MOD001 SL6MOD001 mod001
File Info : application/pdf, 11 Pages, 1.44MB
DocumentDocumentHID® MOD001
Install Guide
Overview
This BEEKsTM BLE Module Install Guide covers the basics of the setup and provisioning of equipment with Bluzone cloud account and project. This install guide is intended for technicians. The HID BEEKs Bluetooth Low Energy (BLE) Module supports transmission of data from wired sensors utilizing a variety of protocols, including UART, SPI, and I2C. Additionally, the built-in 12-bit analog-to-digital converter provides support for analog output sensors. The BEEKs BLE Module therefore enables custom solution development for a wide range of applications. When combined with HID Global's end-to-end IoT ecosystem, which includes BluFiTM BLE-to-WiFi gateways and the BluzoneTM cloud services, the BLE Module can be centrally managed remotely through the cloud to transfer new messages and firmware updates. The unique design allows BEEKs BLE Module to broadcast reliably, even in densely populated WiFi environments. The BLE radio enables the module to transmit the data from wired analog and digital sensors for a variety of applications. Bluzone allows you to control the transmitting capabilities of the module.
System components
1 3
2
1 BluFiTM model BluFi-AC00 Bluetooth to WiFi Gateway 2 Bluzone Cloud Fleet Management and Condition
Monitoring dashboard. 3 BLE Module model MOD001 Bluetooth Low Energy Module
Best practices
· Maximum of 15 20 beacons per BluFi for best results · Maximum 20 30 meters from beacon to BluFi for best
results (distance will decrease for increased interference/ blockages). For RTLS applications, the BEEKS Duress Badge signal must be received by at least three BluFis in the vicinity.
Network troubleshooting
· 2.4 GHz WiFi only · HTTPS port 443 must be open · DHCP required · 1 Mbps upload speed required · Captive WiFi portals not compatible · Compatible certificate formats: .pem, .der · Some networks may require adding the BluFi MAC
address to an allowlist
Terminology
1
WiFi
WiFi
Bluetooth
Bluetooth
3 2
1 Bluzone Secure cloud-based SaaS to centrally manage BEEKs via BluFi gateways. Additionally, monitor, store and analyze performance data collected from deployed fleet.
2 BluFi Gateway Receives data from BEEKs over Bluetooth and sends to Bluzone Cloud.`
3 BLE Module Sends data from wired sensors to BluFi.
Prerequisites
· Set up Bluzone account · Download Bluzone mobile app · Additional installation guides are available and can be
found at: https://hid.gl/HID-BluFi-installation
PLT-06387, Rev. A.0
1
January 2022
Powering Trusted Identities
1. Module mounting
HID® MOD001
Install Guide
BLE Modules should be mounted with screws to rigid standoffs using the two through-holes on the printed circuit board assembly (PCBA).
Hole 1 diameter (2 mm) 23.50 mm
Hole 2 diameter (2 mm)
Hole 1 location (3.62 mm X 10.03 mm)
30.50 mm
Hole 2 location (5.91 mm X 5.90 mm)
The modules may be mounted in a custom enclosure or to a surface that is isolated from contact. It is recommended that the module be covered to avoid damage to the board and components.
PLT-06387, Rev. A.0
2
January 2022
Powering Trusted Identities
2. Initial set up
HID® MOD001
Install Guide
2.1 Account set up
1. Visit bluzone.io and register a new account. Verify your email by clicking on the link emailed to you.
2.2 Project set up
1. Use the drop-down menu in the top right portion of the screen to create a new project.
2. Go to Settings and send a Product Activation request for your use case e.g. RTLS, Status Monitoring or Advanced Condition Monitoring, depending on the SaaS model you have purchased. Your product features will be activated within 24 hours.
PLT-06387, Rev. A.0
3
January 2022
Powering Trusted Identities
2.3 Bluzone mobile app setup
1. Download the Bluzone mobile app from Google Play or the iOS App Store.
2. Login to your account with Bluzone credentials.
HID® MOD001
Install Guide
2.4 BEEKs BLE Module provisioning
1. Power on the module with a 3.6 - 30 VDC supply voltage and place the module close to a BluFi (don't install on assets yet).
2. For each module, hold the mobile device close to the module and select the device with highest signal strength (swipe down to refresh list). Continue the steps for each BEEKs module.
3. When prompted for a Template, select the template that corresponds to your custom use-case.
4. Assign the module a name that coincides with the asset on which it is installed.
PLT-06387, Rev. A.0
4
January 2022
Powering Trusted Identities
3. BEEKs and BluFi installation
3.1 BluFi installation
BluFi should be installed within 100ft (30m) of monitored assets (shorter distances are required for environments with obstructions). · BluFi AC:
HID® MOD001
Install Guide
3.2 BLE Module
1. Place beacons near the desired assets (don't install yet). 2. In Bluzone console, go to BluFi > {BluFi Name} >
Statistics and scroll down to the Scan Map. 3. Verify that each beacon sees at least one BluFi. (-75
dBm or higher is desired). Move any BluFi, if necessary.
· BluFi DC:
3.3 BLE Module installation
1. Connect the wired sensor (for your use-case) to the BLE Module.
2. Power on the BLE Module using 3.6 - 30 VDC power supply.
BluFi DC
BluFi DC Plenum
3. (Optional) Connect external antenna to the U.FL coaxial connector.
4. BLE Modules should be mounted with screws to rigid standoffs using the two through-holes on the printed circuit board assembly (PCBA).
PLT-06387, Rev. A.0
5
January 2022
Powering Trusted Identities
5. The modules may be mounted in a custom enclosure or to a surface that is isolated from contact. It is recommended that the module be covered to avoid damage to the board and components.
HID® MOD001
Install Guide
PLT-06387, Rev. A.0
6
January 2022
Powering Trusted Identities
HID® MOD001
Install Guide
Specifications
BEEKs BLE Module Model: MOD001
Available configurations
MOD001 (Most comprehensive)
Base model board with
Description
components to support generic data input through I2C, SPI, and
analog sensors.
MOD001-UART
MOD001-Badge
Board with components to support serial data input via UART connection; raw data advertised in sBeacon packets.
Board with components to support use of module in a badge application for location service use-cases
Dimensions 30.5mm x 23.5mm
30.5mm x 23.5mm
30.5mm x 23.5mm
Frequency Range 2400-2483.5 MHz
Number of Channels 40
Modulation GFSK
Mode of operation Half-duplex
RF output power (max) +5 dBm
Data Rate 1 Mbit/s
Antenna PCB antenna, antenna gain 0.30 dBi
External Antenna (optional) TAOGLAS WCM.01.0111 2.4GHz Button Antenna. Antenna Gain 0.89 dBi
Power Supply Input Voltage 3.6--30 VDC
Operating temperature -22° to +140° F (-30° to +60° C)
Power consumption -RX 7.5 mA RX Active Mode
Power consumption-TX 6.5 mA TX Active Mode
Power consumption-sleep 1.6 A (SRAM retention and RTC running)
CPU Dual Code: ARM Cortex M3 (32 bit, 48 MHz) main CPU, ARM Cortex M0 (16 bit) sensor controller
128 KB flash (MCU) Flash Memory 512 KB additional flash
Type Feature
· Bluetooth Low Energy 4.2 compliant single mode protocol stack · GAP, SM, GATT, ATT, L2CAP and Link layer protocols · Peripheral and broadcaster roles BLE Stack · Central role · Observer and limited master role · Fully embedded software architecture. No bifurcation between Host and Controller
· Packets per connection interval - Configurable up to 12 · Connection parameters update Link-Layer · Connection channel map update · Connection graceful terminate · AES128 Encryption request and response
· ~54 kB stack and application size (Flash non-volatile memory) Memory · ~8 kB RAM requirement
· No memory Isolation between application and protocol stack
PLT-06387, Rev. A.0
7
January 2022
Powering Trusted Identities
HID® MOD001
Install Guide
Type Feature
· Reverse RSSI Advertising · Configurable interval
· Configurable adaptive advertisement mode for lower power consumption
Operating System Bare metal implementation by HID
· iBeacon support · sBeacon support Application supported · Eddystone support · Fully open and easily configurable for 3rd party Beacon protocol · Bluzone Cloud-Key-vault managed security · Unique internal key per individual Beacon Security · Internal Device ID per individual Beacon (sBV2ID) · Internal UNIX time clock / Timer since "on" (Manufacture) · RSA Private/Public with(Bluzone Cloud - key/vault)-Communication from/to Beacon encrypted use RSA
PLT-06387, Rev. A.0
8
January 2022
Powering Trusted Identities
4. Regulatory information
HID® MOD001
Install Guide
SRD Model: MOD001
RF Specifications
Standard protocol BLE 4.2 Frequency band 2400-2483.5 MHz
No of RF channels 40 RF output power +5 dBm Modulation GFSK Antenna PCB, 0.30 dBi
Communication Regulation
The following is a list that applies: US FCC United States Compliance FCC ID: SL6-MOD001 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT: Changes or modifications to this product not authorized by HID, could void the FCC Certification and negate your authority to operate this product. Note: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This module is certified pursuant to two Part 15 rules sections(15.247). Integrator / End Product The user manual of the end product should include: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Label of the end product: The host product must be labeled in a visible area with the following "Contains FCC ID: SL6-MOD001". The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Canada Compliance 24824-MOD001 This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20cm de distance entre la source de rayonnement et votre corps OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the IC authorization is no longer considered valid and the IC number can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate IC authorization.
OEM Integrator Notice End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: "Contains transmitter module IC: IC: 24824-MOD001". Contient le module d'émission IC: IC: 24824-MOD001 The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or online. This device is intended only for OEM integrators under the following conditions: 1. The antenna must be installed such that 20cm is maintained between the antenna and users, and 2. The transmitter module may not be co-located with any other transmitter or antenna. Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1. L'antenne doit être installée de telle sorte qu'une distance de 20cm est respectée entre l'antenne et les utilisateurs, et 2. Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Australia/ New Zealand Compliance This product conforms to Australia and New Zealand Radio Requirements.
Japan
217-220435
UK Compliance
PLT-06387, Rev. A.0
9
January 2022
Powering Trusted Identities
European Union Compliance Conformite Européenne (European Community)
Hereby, HID Global declares that this Radio Equipment SRD Model number MOD001 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following Internet address: www.hidglobal/certifications This product operates at the following frequencies: · 2.4 GHz band with an RF output power of less than +5 dBm e.i.r.p.
Czech Spolecnost HID Global tímto prohlasuje, ze toto radiové zaízení, císlo modelu MOD001, odpovídá pozadavkm smrnice 2014/53/EU. Úplný text EU Prohlásení o shod je k dispozici na následující internetové adrese: www. hidglobal/certifications Tento výrobek pouzívá následující frekvence: · frekvencní pásmo 2,4 GHz, picemz výstupní RF výkon je nizsí nez +5dBm
EIRP
Greek , HID Global M MOD001 O 2014/53/E. : www.hidglobal/certifications : · 2,4 GHz (RF)
+5dBm e.i.r.p. ( )
Dutch Hierbij verklaart HID Global dat deze radioapparatuur modelnummer MOD001 in overeenstemming is met Richtlijn 2014/53/EU. De volledige tekst van de Europese conformiteitsverklaring is te vinden op de website: www.hidglobal/certifications Dit product werkt op de volgende frequenties: · 2,4 GHz-band met een RF-uitgangsvermogen van minder dan +5 dBm
e.i.r.p.
Danish HID Global erklærer hermed, at dette radioudstyr modelnummer MOD001 er i overensstemmelse med direktiv 2014/53/EU. Den fulde tekst i EU- overensstemmelseser- klæringen kan læses her: www.hidglobal/ certifications Dette produkt fungerer ved følgende frekvenser: · 2,4 GHz-bånd med en RF-udgangseffekt på mindre end +5dBm e.i.r.p.
Estonian Käesolevaga kinnitab HID Global, et see raadioseadmestik mudelinumbriga MOD001 on vastavuses direktiiviga 2014/53/EL. Kogu EL-i vastavusdeklaratsiooni tekst on saadaval järgmisel internetiaadressil: www. hidglobal/certifications See toode töötab järgmistel sagedustel. · 2,4 GHz ribalaiusel raadiosagedusliku väljundvõimsusega vähem kui +5
dBm e.i.r.p.
Maltese Hawnhekk, HID Global tiddikjara li dan it-Tagmir tar-Radju bin- numru tal-mudell MOD001 huwa konformi mad-Direttiva 2014/53/UE. It-test si tad- dikjarazzjoni ta' konformità tal- UE hu disponibbli f'dan l- indirizz fuq l-Internet: www.hidglobal/certifications Dan il-prodott jopera fil- frekwenzi li ejjin: · 2.4 GHz band b'RF output power ta' inqas minn +5 dBm e.i.r.p.
HID® MOD001
Install Guide
German Hiermit erklärt HID Global, dass dieses Funkgerätmodell Nr. MOD001 der Richtlinie 2014/53/EU entspricht. Der vollständige Text der EU- Konformitätserklärung steht unter der folgenden Internetadresse zur Verfügung: www.hidglobal/certifications Dieses Produkt arbeitet mit den folgenden Frequenzen: · 2,4-GHz-Band mit einer HF-Ausgangsleistung von weniger als +5dBm EIRP
Finnish HID Global vakuuttaa täten, että tämä radiolaite, mallinumero MOD001, vastaa direktiiviä 2014/53/EU. EUvaatimustenmukaisuus- vakuutuksen koko teksti on saatavissa seuraavasta Internet-osoitteesta: www.hidglobal/certiifcations Tämä tuote toimii seuraavilla taajuuksilla: · 2,4 GHz:n kaista, RF- lähtöteho alle +5 dBm EIRP
Swedish Härmed intygar HID Global att denna radioutrustning modell nummer MOD001 överensstämmer med direktiv 2014/53/EU. Den fullständiga texten med intyg om överensstämmelse för EU finns på följande internetadress: www.hidglobal/certifications Den här produkten fungerar på följande frekvenser: · 2,4 GHz-band med en RF-uteffekt på mindre än +5dBm e.i.r.p.
French Par la présente, HID Global déclare que cet équipement radio Modèle MOD001 est conforme à la directive 2014/53/UE. Le texte intégral de la déclaration de conformité de l'UE est disponible sur le site Internet: www. hidglobal/certifications Ce produit fonctionne aux fréquences suivantes: · dans la bande de 2,4 GHz avec une puissance de sortie RF inférieure à
+5dBm PIRE
Italian Con il presente documento, HID Global dichiara che la presente apparecchiatura radio modello MOD001 è conforme alla direttiva 2014/53/ UE. Il testo completo della dichiarazione UE di conformità è disponibile su Internet al seguente indirizzo: www.hidglobal/certifications Questo prodotto funziona alle seguenti frequenze: · Banda a 2,4 GHz con potenza di uscita RF inferiore a +5 dBm EIRP
Polish Firma HID Global deklaruje niniejszym, e to urzdzenie radiowe, model numer MOD001, spelnia wymogi okrelone w Dyrektywie 2014/53/UE. Pelny tekst deklaracji zgodnoci UE jest dostpny pod nastpujcym adresem internetowym: www.hidglobal/certifications Ten produkt dziala na nastpujcych czstotliwociach: · w pamie 2,4 GHz z równowan moc wyjciow RF wypromieniowan
izotropowo (EIRP) mniejsz ni +5dBm.
Croatian Ovime tvrtka HID Global izjavljuje da je ova radijska oprema model MOD001 u skladu s Direktivom 2014/53/EU. Cjelokupan tekst europske izjave o sukladnosti dostupan je na sljedeoj internetskoj stranici: www.hidglobal/ certifications Ovaj proizvod radi pri sljedeim frekvencijama: · pri frekvenciji od 2,4 GHz s izlaznom RF snagom manjom od +5dBm e.i.r.p
Lithuanian Siuo ,," deklaruoja, kad sis radijo rangos modeHID Global lis, kurio numeris MOD001, atitinka Direktyv 2014/53/EB. Vis ES atitikties deklaracijos tekst galite rasti siuo interneto adresu: www.hidglobal/certifications Sis gaminys veikia tokiais dazniais: · 2,4 GHz daznio diapazonas, RD isvesties galia yra mazesn nei +5 dBm
EIRP.
PLT-06387, Rev. A.0
10
January 2022
Powering Trusted Identities
Slovenian Druzba HID Global izjavlja, da je ta radijska oprema, stevilka modela MOD001, v skladu z Direktivo 2014/53/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu: www.hidglobal/ certifications Ta izdelek deluje pri naslednjih frekvencah: · 2,4 GHz z izhodno mocjo RF manj kot +5dBm e.i.m.o. (EIRP)
Hungarian A HID Global ezúton nyilatkozza, hogy ez az MOD001 típusszámú rádióberendezés megfelel a 2014/53/EU irányelvnek. Az EU megfelelségi nyilatkozat teljes szövege elérhet a következ internetes címen: www. hidglobal/certifications A termék a következ frekvenciákon üzemel: · 2,4 GHz-es sáv, mely esetében RF kimeneti teljesítménye kevesebb, mint
+5 dBm EIRP
Latvian Ar so uzmums HID Global apliecina, ka s radioiekrta, modea numurs MOD001, atbilst Direktvas 2014/53/ES prasbm. Pilnu ES atbilstbas deklarcijas tekstu var skatt vietn www.hidglobal/certifications Sis izstrdjums darbojas ar sdm frekvencm: · 2,4 GHz josla; radiofrekvences izvades jauda ir mazka par +5 dBm
(ekvivalent izotropiski izstarot jauda).
Slovak Spolocnos HID Global týmto vyhlasuje, ze toto rádiové zariadenie, model MOD001, je v súlade so smernicou 2014/53/EÚ. Úplné znenie vyhlásenia o zhode so smernicami EÚ je k dispozícii na stránke: www.hidglobal/ certifications Toto zariadenie pracuje pri nasledujúcich frekvenciách: · 2,4 GHz pásmo s RF výstupným výkonom nizsím ako +5dBm EIRP
Romanian Prin prezenta, HID Global declar c acest echipament radio numr model MOD001 ste în conformitate cu Directiva 2014/53/UE. Textul complet al declaraiei de conformitate UE poate fi gsit la urmtoarea adresde internet: www.hidglobal/certifications Acest produs funcioneazla urmtoarele frecvene: · în banda 2,4 GHz cu o putere de ieire RF de mai puin de +5dBm E.I.R.P.
Portuguese Por este meio, a HID Global declara que este modelo de equipamento de rádio, número MOD001, está em conformidade com a Diretiva 2014/53/UE. O texto completo da declaração de conformidade da UE está disponível no seguinte endereço da Internet: www.hidglobal/certifications Este produto opera nas frequências seguintes: · 2,4 GHz com uma potência de saída de RF inferior a +5dBm e.i.r.p.
Spanish Por la presente, HID Global declara que este equipo de radio, modelo número MOD001 cumple la Directiva 2014/53/EU. El texto completo de la Declaración de Conformidad CE está disponible en la siguiente dirección de internet: www.hid global/certifications Este producto opera en las siguientes frecuencias: · Banda de frecuencia de 2,4 GHz con una potencia de salida de RF (PIRE)
de menos de +5dBm.
HID® MOD001
Install Guide
hidglobal.com
© 2022 HID Global Corporation/ASSA ABLOY AB. All rights reserved. PLT-06387, Rev. A.0 Part of ASSA ABLOY For technical support, please visit: https://support.hidglobal.com