SmallRig Remote Control User Manual

In order to ensure user’s safety and prevent product damages caused by any improper use, please carefully read the "Warning" below and properly keep this User Manual for future reference.

Thank you for purchasing SmallRig’s product.

Warnings

• Please read this User Manual carefully.
• Do not use the product in water because it is not dust or water proof.
• Do not let the product fall to the ground, be hit or suffer violent impact.
• Since there are some hazardous substances in the battery, please do not carelessly discard the product. Please follow the waste management measures to deal with damaged product or product that is no longer used.

! This product has a removable coin cell battery built in, please keep out of reach of children.

Intended Use

• Please read this User Manual carefully, especially the "Warnings".
• Please use or store the product in the environment mentioned herein.
• It will be regarded as an improper use when users do not correctly follow the user manual or use the product under the specific working condition.

Wireless Connection

To connect, toggle the wireless controller switch from "OFF" to "ON". The green light flashes to indicate that the wireless pairing mode is turned on. Open your phone's wireless settings, search for "3646" to connect. The green light flashes slowly after successful connection. Press the photo button to take a photo or a video.

Sleep Mode and Restart

If there is no user input within 3 minutes in the connection status, the wireless controller will activate sleep mode. Pressing the photo button will wake up the connection.

Maximum Working Distance

In the absence of any obstacle or interference, the maximum working distance of the wireless remote control is 10 meters. Connection will be cut off beyond 10 meters and can be recovered when back within the working range.

Adaptation

The controller supports iOS 10.0 and above operating systems, Harmony, and Android 8.0 and above operating systems for connection management.

Battery Replacement

When the controller's power is lower than 2.2V, the indicator light brightness dims, indicating a low battery status. The user can remove the back screw to replace the battery (battery model: "CR2032").

An illustration shows the process of removing the back screw for battery replacement.

Product Specification

Warranty Card Information

The following fields are for warranty registration:

• Serial No.
• Item Name
• Purchase Date
• User Name
• Mobile
• Address
• Receipt

(Note: These labels are in Chinese: 保修卡)

Service Warranty

Please keep your original and guarantee card. Ensure the dealer has written the date of purchase and SN of the product on it. These are required for warranty service.

After-sale Warranty Terms

1. 7-Days DOA Return Policy: Within 7 days from the date of package receipt, return or replacement can be done if the item received is malfunctioning or physically damaged (not caused by human abuse). Return shipping cost will be on SmallRig’s charge.
2. 1-Year Warranty: Within 1 year from the date of package receipt, a defective product not caused by human abuse is eligible for free repair/replacement. A defective product damaged by human abuse will incur charges based on the damage level for repair/replacement.

This warranty does not cover:

• Defects caused by user’s violation of the "Warnings" and "Intended Use".
• The product identification or SN label is removed or defaced in any way.
• The product is serviced or repaired by anyone other than SmallRig or a service agency authorized by SmallRig.

Manufacturer Information

Made in China

Manufacturer: Shenzhen Leqi Network Technology Co., Ltd.

Address: Rooms 103, 501 and 601, Building 5, Fenghe Industrial Park, Nos. 1301-50 Guanguang Road, Longhua District, Shenzhen, Guangdong, China.

Website: www.smallrig.com

Product ID: 3646

Certificates

Certificates: CE, Rosh, FCC, FCC ID

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0cm between the radiator and your body.

ISED Statement

English: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).

French: Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. L'appareil numérique du ciem conforme canadien peut - 3 (b) / nmb - 3 (b).

This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure. Users can obtain Canadian information on RF exposure and compliance.

Cet appareil est conforme à l'exemption des limites d'évaluation courante dans la section 2.5 du cnr - 102 et conformité avec rss 102 de l'exposition aux rf, les utilisateurs peuvent obtenir des données canadiennes sur l'exposition aux champs rf et la conformité.

This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0cm between the radiator & your body.

Cet équipement est conforme Canada limites d'exposition aux radiations dans un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 0 cm entre le radiateur et votre corps.