GT6 Smart Watch User Guide

Part Introduction

1. Wearing Position: For optimal performance, wear the watch behind the ulnar styloid bone (the bony protrusion on the pinky-finger side of your wrist).

2. Adjustment: Adjust the strap to fit your wrist snugly by using the adjustment holes and fastening the clasp. Ensure a comfortable fit.

3. Sensor Contact: The sensor on the back of the watch must be in close contact with your skin to ensure accurate readings and prevent movement.

Quick Instructions for Use

First-time Use: Remove the watch and charge it using the provided charger. The watch will automatically power on during charging.

Charging Method: Align the two contacts on the charger with the charging points on the back of the watch. The magnetic charging base will attach automatically. Connect the other end to a standard USB port (5V charging voltage).

Power On/Off:

• Power On: While the watch is off, charge it or long-press the side button for 3 seconds until it vibrates.
• Power Off: From the shutdown interface, short-press the green option to shut down with vibration. Long-press the side button to bring up the shutdown interface.

Watch Operation:

• Wake Screen: Short-touch the screen to light it up. Click or slide to switch displays. (Touch wake-up is off by default but can be enabled via the app).
• Screen Off: The screen will automatically turn off after 5 seconds of inactivity. Users can connect to the mobile app to modify the screen-off time.
• Notifications: Incoming call and message reminders are off by default. Users can enable or disable them in the app's main interface.

Install the Smart Watch APP

Scan the QR codes provided or search for "GloryFit" in major app stores to download and install the application.

Device Requirements: iOS 9.0 and above; Android 4.4 and above, supporting Bluetooth 4.0.

Device Attachment (Connection)

For first-time use, connect the watch to the app for calibration. Successful connection automatically synchronizes the time. Inaccurate step counting and sleep data may occur if not connected.

Connection Process:

1. Open the mobile phone APP.
2. Click the profile icon (Me → Click avatar).
3. Tap "Add device" (iOS) or "Add device" (Android).
4. Click the search icon in the upper right corner.
5. Select your device to connect.

Bluetooth Connection: After successful pairing, the app saves the watch's Bluetooth address. The app will automatically search and connect to the watch when opened or running in the background.

Data Synchronization: Manually pull down on the app's home page to sync data. The watch can store up to 7 days of offline data. Synchronization time varies with data volume, taking up to approximately 2 minutes. A "Sync complete" notification will appear.

APP Functions and Setting

Personal Information and Exercise Goals:

• In the app, navigate to "Me" and click your avatar.
• Set your profile picture, gender, age, height, and weight to improve data accuracy.
• Customize daily exercise goals. A well-planned exercise routine contributes to better physical fitness.

Main Functional Interface

Main Interface: The watch offers multiple main interfaces. Long-press the main interface for three seconds to switch between them. After initial pairing, the watch synchronizes time, date, and day of the week from your phone.

Message Push Interface: Features a 1.32-inch large screen with large fonts for easy viewing and displaying more content.

Status Interface: Displays current steps, distance, and calories. Distance and calories are calculated based on your steps, height, and weight set in the app.

Heart Rate Interface:

• Switch to the heart rate interface and click the screen to start detection. Press the side button to exit after testing.
• Alternatively, connect to the mobile app to test/stop from the heart rate interface.
• If the watch is worn incorrectly or the test fails, a failure interface will be displayed.
• Heart rate detection mode reduces battery life.

Heart Rate Test Notes:

• During testing, the heart rate LED light on the back will illuminate.
• Ensure the sensor is close to the skin to prevent external light from affecting accuracy.
• Keep the test area clean; sweat or stains can impact results.

Blood Pressure Interface:

• Switch to the blood pressure interface and click the screen to begin measurement. Press the side button to exit blood pressure mode after completion.
• If a test starts but yields no result, the previous result or "--/--" will be displayed.
• You can also connect to the phone app to test/stop from the blood pressure interface; failure results are similar.

Sports Interface: Switch to this interface and click the screen to enter specific sports modes. It includes 24 activities like jump rope, swimming, cycling, table tennis, tennis, and badminton. Slide the screen to switch between modes. Press the side button to return and exit the sports interface.

Information Interface: In the message interface, click the screen to view messages. Slide to turn pages. Press the side button to exit after viewing.

Settings Interface: Navigate to sub-menus by clicking related interfaces for further operations.

Reminding Function

To use reminder functions, enable the switch in the app's "Setting Center". Ensure the phone and watch are connected via Bluetooth for vibration alerts when messages arrive.

Notification Types:

• Call Reminders: The watch vibrates and displays the caller's name or number. If the "Reject Call" function is enabled in the app, a single tap on the hang-up button can reject the call.
• Message Reminders: Upon receiving a text message, the watch vibrates and shows an icon. Click to view the message content.
• QQ Reminders: For QQ messages, the watch vibrates and displays an icon. Click to view the content.
• WeChat Reminders: For WeChat messages, the watch vibrates and displays an icon. Click to view the content.
• Smart Alarm: Set up to three alarms, which sync to the watch. These are silent alarms that use moderate vibration. Offline alarm reminders are supported.
• Sedentary Reminders: Default interval is one hour. When enabled and connected, if no movement is detected for an hour, the watch vibrates to prompt activity.
• Other Reminders: For emails or other notifications, the watch vibrates and displays an icon. Click to view the content.
• Charging Reminders: The motor vibrates when the watch is connected to power for charging. The watch does not vibrate when the battery is low.

Sleep Detection Function

When you fall asleep, the watch automatically enters sleep monitoring mode. It tracks deep sleep, light sleep, and wakefulness duration to calculate sleep quality. Sleep data is currently only viewable in the app. Note: Sleep data is only recorded if the watch is worn while sleeping.

Common Problems

Why is the first heart rate test too long?

The initial heart rate test requires collecting a longer signal from different users to accurately calculate your heart rate.

Bluetooth Connection Issues (Failure or Slow Reconnection):

1. Device Compatibility: Ensure your device runs iOS 9.0+ or Android 4.4+ and supports Bluetooth 4.0.
2. Signal Interference: Bluetooth connections can be affected by signal interference. Operate in an environment free from magnetic fields or multiple Bluetooth devices.
3. Toggle Bluetooth: Turn your phone's Bluetooth off and then on again.
4. Restart Device: Close background apps on your phone or restart your phone.
5. Other Devices: Avoid connecting to other Bluetooth devices or functions simultaneously.
6. App Background: Ensure the "GloryFit" app is running normally in the background. It may not connect if it's not running.

Cannot Search for the Watch:

Ensure the watch is powered on, activated, and not paired with another phone. Bring the watch closer to the phone. If still unsuccessful, turn off your phone's Bluetooth for 20 seconds, then restart it.

Why wear the watch tightly for heart rate measurement?

The watch uses a light reflection principle. It measures heart rate by collecting signals reflected from the skin back to the sensor. Wearing it loosely allows ambient light to enter the sensor, affecting measurement accuracy.

No Reminders Despite Enabling the Function:

• Android: Confirm the phone and watch are connected. In phone settings, grant "GloryFit" app permissions for calls, messages, and contacts. Keep "GloryFit" running in the background. Add "GloryFit" to your phone's trusted apps if security software is installed.
• iPhone: If no reminders appear after connection, restart your phone and reconnect. When reconnecting, wait for the "Bluetooth pairing request" prompt and tap "Pair" for reminders to function.

Is the Smart Watch Waterproof?

It supports IP68 waterproof and dustproof rating. You can wear it for daily activities like washing hands, in the rain, cold showers, or car washing. (Note: IP68 standard typically means submersion up to 1 meter for 30 minutes at 35 degrees Celsius, though the text here is slightly ambiguous about the exact conditions for "IP68").

Does Bluetooth Connection Need to Be Open All the Time? Is Data Retained After Disconnection?

Data is stored on the watch host for up to 7 days before synchronization. When Bluetooth is connected, data automatically uploads to the mobile terminal. Please sync data promptly. Note: Call and SMS alerts require an active Bluetooth connection, but alarm reminders work offline.

Matters Needing Attention

• Avoid strong impacts, extreme heat, and direct sunlight.
• Do not disassemble, repair, or modify the device yourself.
• Charge using a 5V 500mA power source. Do not use overvoltage power supplies.
• Operate within a temperature range of 0°C to 45°C. Do not dispose of in fire to prevent explosions.
• If the watch gets wet, dry it with a soft cloth before charging to prevent corrosion of charging contacts and potential charging failures.
• Do not use in high-pressure or high-magnetic environments.
• If you have sensitive skin or wear the watch too tightly, you may experience discomfort.
• Wipe sweat from your wrist promptly. Prolonged contact with soap, sweat, allergens, or contaminants can cause skin irritation or allergies.
• For frequent use, clean the watch weekly. Wipe with a damp cloth and mild soap to remove dirt or oil.
• Avoid wearing the watch during hot showers.
• After swimming, dry the watch immediately to keep it dry.

Basic Parameters

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

FCC ID: 2A2L4-GT6