WIFI RECEIVER

Introduction

The WIFI RECEIVER is designed for various access control systems, intercom systems, and garage door systems. It enables users to open doors remotely via a smartphone from any location.

The unit operates on a DC12V power supply and outputs a switching signal, which can be connected to the switch signal input of a garage or gate opener. A built-in wireless module requires a strong WiFi signal for seamless operation. It is important to ensure adequate WiFi signal strength at the installation location. Note that enclosing the device within metal casings or motors may restrict its WiFi signal.

Technical Parameters

• Working Voltage: DC12V
• Working current: ≤210mA
• Standby current: ≤80mA
• Working mode: Control via Mobile APP (eWeLink)
• Networking method: WiFi@2.4GHz 802.11b/g/n, supporting WPA/WPA2 security modes
• Wireless network type: STA/AP/STA+AP
• Security Mechanism: WEP/WPA-PSK/WPA2-PSK
• Encryption type: WEP64/WEP128/TKIP/AES
• Firmware upgrade: OTA remote upgrade
• Environment humidity: 10%~90%RH
• Adaptive temperature: -35°C to 125°C
• Physical dimension: 83*83*27mm

Connection Method

Basic Receiver to Motor Connection:

Connect the red and black cables to the push button terminal on the motor. The red cable typically connects to terminals labeled PB, WB, PUSHBUTTON, WALLBUTTON, or OSC (consult your opener manual for specific labels). The black cable connects to terminals labeled GND, COM, Common, or Ground.

Diagram Description: A diagram illustrates the connection points. Power input terminals are labeled "+12V" and "GND". Output terminals are labeled "NO" (Normally Open) and "COM" (Common).

Mobile App Download and Operation Instructions

To control the WIFI RECEIVER, download the "eWeLink" mobile application from your device's app store or by searching for "eWeLink".

1. After downloading, open the eWeLink app and register an account, then sign in.
2. Confirm the device is correctly connected to the circuit and powered on.
3. Ensure your smartphone is connected to your WiFi network and you have the correct WiFi password.
4. Press and hold the configuration button on the device for more than 5 seconds. The indicator light should change from red to blue and flash 3 times, indicating it's in pairing mode.
5. In the eWeLink app, tap the "+" button (usually located at the bottom center) to add a new device.
6. Select the "Quick Add" mode.
7. Choose your WiFi network name from the list and enter the WiFi password. Click "Next step".
8. The app will attempt to connect the device to your network.

If a pairing failure occurs, follow the prompts provided by the app for troubleshooting and repeat the connection steps. Once connected, you can rename the device and access its management page for further settings and sharing options.

Extended Functions

• Enable scene actions by linking multiple devices.
• Integrate with compatible cameras, such as eWeLink cameras, Haikang fluorite cameras, and eWeLink intelligent visual doorbells for enhanced monitoring capabilities.
• Utilize intelligent voice control by connecting with popular voice assistants like Amazon Alexa, Google Home, IFTTT, Nest, Xiaomi Mijia, Tmall Elf, Fluorite, and Dingdong.

Precautions

• The device can only be configured by one account at a time. To allow other users to configure the device, it must be deleted from the current app account after testing or completion.
• For sharing the device with other users, they must first register an account and enable notification permissions within the "eWeLink" app. For face-to-face sharing, users should log into their account and navigate to the "eWeLink" APP page to await the sharing notification.
• It typically takes approximately 5 seconds for the device to connect to the network after being powered on.
• When adding users in batches, use the WeChat sharing function. Recipients of the shared link will gain access rights to the device.
• The device supports recording the last 10 execution events; generally, 5 effective records are retained.