larm.com
P65Warnings.ca.gov
SECO-LARM USA Inc
Instruction Manual for Seco Larm models including: SL-1301-SAQ-A, SL-1301-BAQ-A, SL-1301-EAQ-A, SL-1301-SAQ-A LED Strobe Lights, SL-1301-SAQ-A, LED Strobe Lights, Strobe Lights, Lights
Seco Larm SL-1301-SAQ/A - 24V Amber Strobe w/Siren - Southwest Automated Security
Seco Larm SL-130-BAQ/A - 24V Amber Strobe - Southwest Automated Security
Seco Larm SL-1301-EAQ/A - 9-15V Amber Strobe - 6 LEDs, Flash Only - Southwest Automated Security
File Info : application/pdf, 4 Pages, 194.96KB
DocumentDocumentLED Strobe Lights Manual (SL-1301-SAQ shown) Color LEDs 6 LED Red SL-1301-EAQ/R Blue SL-1301-EAQ/B Amber SL-1301-EAQ/A Clear SL-1301-EAQ/C Green SL-1301-EAQ/G *Includes a built-in 100dB siren 32 LED SL-1301-BAQ/R SL-1301-BAQ/B SL-1301-BAQ/A SL-1301-BAQ/C SL-1301-BAQ/G 54 LED SL-1301-SAQ/R* SL-1301-SAQ/B* SL-1301-SAQ/A* SL-1301-SAQ/C* SL-1301-SAQ/G* All Models: Utilizes high-intensity LEDs Operating life of over 50,000 hours (over 5.7 years) Same size as the SL-126Q strobe light Simple 2-wire installation 5 lens colors available for each model Weather resistant High-impact resistant case High-impact and heat-resistant lens Reverse polarity protection Visible in all directions BAQ series includes all features of the EAQ plus: 5 Vertical LED strips (32 LEDs total) increase visibility from various directions 8 Different flashing patterns and adjustable duty cycle Adjustable flashing speed Backup battery available for continuous lighting applications SAQ series includes all features of the BAQ plus: 10 Vertical LED strips (54 LEDs total) Built-in 100dB siren (programmable) except SL-1301-EAQ ENFORCER LED Strobe Lights Introduction: ENFORCER LED Strobe Lights provide all the functions of a regular strobe light and much more. Each has an operating life of 50,000 hours--over 160 times that of a regular strobe light. No more bulbs to replace! There are three models--with 6~54 LEDs. The BAQ series and SAQ series include a unique placement of LEDs making the light more visible from various directions, a 9V backup battery option making them ideal for continuous lighting applications, and 8 selectable strobe patterns, adjustable duty cycle, and adjustable strobe speed. The SAQ series also includes a built-in 100db siren. Parts List: 1x LED Strobe Light *SL-1301-EAQ only 1x Adhesive gasket* 2x Mounting Screw with "O" rings 1x Manual Specifications: Model Vertical LED strips Total number of LEDs SL-1301-EAQ 0 6 SL-1301-BAQ 5 32 SL-1301-SAQ 10 54 Operating voltage 9~15 VDC 9~24 VAC/VDC Rotate clockwise Strobe Current drain Steady ON @12VDC (max) Flash with progressive ON Rotate back and forth Flash with progressive ON/OFF Adjustable flash pattern # of flash patterns Adjustable Maximum setting flashing speed Minimum setting Operating life Backup battery function Backup battery Steady ON life Strobe/Flashing Operating temperature Electrical protection Built-in siren IP rating (when installed properly) Base Lens Dimensions *SL-1301-EAQ series has strobe only With siren enabled N/A* 70mA 90mA 150mA 350mA 550mA N/A* 350mA 550mA N/A* 350mA 550mA N/A* 70mA 90mA N/A* 350mA 550mA No* Yes 1* 8 Fixed 260 times/min 120 times/min 80 times/min Over 50,000 hours (over 5.7 years) No Yes N/A Up to 1 hours§ Up to 45min§ N/A Up to 3 hours§ Up to 1.5 hours§ -4°~144° F (-20°~65° C) Reverse polarity protected No Yes (100dB) IP64 IP66 IP55 High-impact resistant black ABS High-impact heat-resistant acrylic ø315/16"x31/8" (ø100x79mm) 9VDC battery not included §Estimated, depending on mode Dimensions: Top View Front View Bottom View 315/16" (100mm) 31/8" (79mm) 21/8" (54mm) 213/16" (71mm) 2 SECO-LARM U.S.A., Inc. Overview: SL-1301-SAQ shown Ground wire (black) Power wire (red) Circuit board LEDs + - (depending on model) LED strips (depending on model) BAT. ON OFF ON / OFF 9-Volt battery clip (under circuit board) (BAQ and SAQ series only) SP ON / OFF Backup battery jumper (default off) (BAQ and SAQ series only) + Siren jumper (default off) (SAQ series only) Strobe speed control (BAQ and SAQ series only) ENFORCER LED Strobe Lights SECO-LARM® SL-1301-BAQ SL-1301-SAQ Remove thinned-out slot for surface wiring ® Mounting screw with 170-208-1 rubber "O" ring 1234 OFF ON DIP switch (BAQ and SAQ series only) Rubber "O" ring Circuit board Circuit board screw Installation: 1. Before starting, please read this manual carefully 6. Remove the lens and mount the LED strobe light (with and keep it for future reference. adhesive gasket for SL-1301-EAQ) to the surface using 2. Be sure to use the LED strobe light within the given the two included mounting screws with rubber "O" rings. electrical limits. If screws are fastened too tightly, the "O" rings will 3. Decide where the LED strobe light is to be be damaged. (SL-1301-EAQ series skip to step 10) mounted. Use a pencil to mark the location of the 7. Select the flash pattern and flash duty cycle using the two mounting screws. DIP Switch (see back page for details) and adjust the 4. Drill a hole through the wall or surface where the speed using the strobe speed control (clockwise to LED strobe light is to be mounted. Run the ground increase, counterclockwise to decrease). (black) and power (red) wires through the wall. 8. Set the siren (SL-1301-SAQ only) to on or off using the Note: For surface wiring applications, remove the siren jumper. thinned-out slot with a pair of pliers. 9. If needed, install backup battery. (See below.) 5. Connect the wires to their respective locations on 10. Replace lens. If lens is fastened too tightly, the "O" an alarm control panel or other security panel. ring will be damaged. Backup Battery (SL-1301 BAQ/SL-1301-SAQ series only) For continuous lighting applications, the backup battery will power the LED strobe light in the event of a power loss. 1. Use a screwdriver to loosen the circuit board screws. 2. Carefully remove and flip the circuit board. The battery holder is attached at the back side of the circuit board. 3. Connect a 9-Volt battery to the battery connector. 4. Replace circuit board and circuit board screws. 9-Volt battery (not included) 5. Turn the backup battery on via the backup battery jumper. Circuit board screw (Circuit board) Troubleshooting: The LED strobe light does not turn on The LED strobe light does not flash correctly Check the LED strobe light's power source Disconnect power, configure correct flash pattern, and reconnect power WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for one (1) year from the date of sale to the original customer. SECO-LARM's obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser's exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM's option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else. SECO-LARM U.S.A., Inc. 3 ENFORCER LED Strobe Lights Configuring Flash Pattern and Duty Cycle (SL-1301-BAQ/SL-1301-SAQ series only): IMPORTANT: Before changing DIP switch, disconnect power. Reconnect power after switches are set. Users may customize both flash pattern and duty cycle (flash patterns 1, 2, and 5 only). The "One-Eighth Duty Cycle" produces a sharper "strobe" effect more like traditional strobe lights. DIP Switch #4 controls the duty cycle for supported flash patterns. Visit www.seco-larm.com for a demonstration of flash patterns / duty cycle. DIP Switch Position Description Flash Pattern Top View (SL-1301-BAQ Shown) Regular Duty Cycle A LED on one-half / off one-half of each cycle (default) (DIP Switch #4 ON, only effective for flash patterns 1, 2, and 5) One-Eighth Duty Cycle B LED on one-eighth / off seven-eighths of each cycle (DIP Switch #4 OFF, only effective for flash patterns 1, 2, and 5) Strobe 1 LEDs flash on and off continuously. (default) (DIP Switch #4 controls the duty cycle) Rotate Clockwise 2 Light rotates clockwise in a circular fashion continuously. (Beacon) (DIP Switch #4 controls the duty cycle) 3 Steady ON All LEDs stay on. Ideal for continuous lighting applications. Flash with Progressive ON 4 LEDs turn on progressively clockwise until all LEDs are lit (sweep), and then turn off. Rotate Back and Forth 5 LED groups light up one at a time clockwise then counterclockwise. (DIP Switch #4 controls the duty cycle) Flash with Progressive ON/OFF 6 LEDs turn on progressively clockwise (sweep), then turn off progressively counterclockwise. Opposite Quarters Flashing Continuously 7 LEDs in opposite quarters flash alternately, repeating continuously. Opposite Quarters Flashing with Pause 8 LEDs in opposite quarters flash alternately for 8 cycles, pause for 2 cycles, and then repeat the pattern. California Proposition 65 Warning: These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov. NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2023 SECO-LARM U.S.A., Inc. All rights reserved. SECO-LARM ® U.S.A., Inc. 16842 Millikan Avenue, Irvine, CA 92606 Phone: (949) 261-2999 | (800) 662-0800 Website: www.seco-larm.com Email: sales@seco-larm.com ® PITSW1 Order Part# 762-509-8% MI_SL-1301-xAQ_230814.docx 4 SECO-LARM U.S.A., Inc.