Bracketron Installation Instructions

Honda Accord (2003-2006) & Honda Accord Hybrid (2005-2006)

Note: Read instructions completely before installing. All instructions are written from the driver's seat position. Exercise caution when handling plastic parts to avoid cracking or breaking.

Tools Needed: Dash Trim Tool (Part #SIT-104), 10mm socket and driver, #2 Phillips screwdriver.

Parts Included: One phone mount, Three (3) #8x3/4" self-tapping screws.

Location of Mount: To the right of the radio.

Step 1: Preparation

Apply the emergency brake, place the transmission in neutral. Remove the trim bezel surrounding the shift lever using the dash trim panel tool, releasing six clips. Carefully remove and set aside the bezel. Locate and remove the two screws in front of the shifter lever.

Step 2: Dash Disassembly

Open the tray cover to the left of the power outlet. Remove the screw at the bottom of the tray. Lift out the tray, releasing two clips. Remove the two screws underneath the tray. Release the three clips holding the power outlet assembly using the dash trim tool and set it aside. Locate the dash bin above the power outlet. Remove the screws in the lower corners of the bin. Close the door and pull the bin out. Locate and remove the two hex head screws securing the lower section of the radio module.

Step 3: Radio Removal

Remove the air vent above the radio using the dash trim panel tool, releasing three clips. Pivot the vent upward and out. Locate and remove three Phillips screws at the top of the radio. Release the three clips at the bottom of the radio below the knobs using the dash trim tool. Carefully grasp the radio and let it hang. Do not disconnect the wire attached to the radio.

Step 4: Mount Installation

Insert the Bezel Mount in the upper right corner of the radio cavity, resting its bottom edge on an internal ledge. Secure the mount using the supplied #8x3/4" self-tapping screws and a #2 Phillips screwdriver. Insert and tighten the first screw in the top hole for angle adjustment, then install the remaining two screws.

Final Steps

Carefully reinstall the dash in reverse order. Install any Bracketron phone holder or AMPS compatible device to your Bezel Mount. Installation is complete.

Lincoln Aviator (2003-2005)

Note: Read instructions completely before installing. Exercise caution when handling plastic parts.

Tools Needed: Dash Trim Tool (Part #SIT-104), Hook Tool (Part #SIT-103), #2 Phillips screwdriver.

Parts Included: Three (3) #8x3/4" self-tapping screws.

Location of Mount: To the Right of the Air Vent.

Step 1: Air Vent Module Removal

Remove the center console air vent module secured by four clips. Insert the Dash Panel Trim tool between the climate control and air vents on the right side. Pull backward to release the lower-right clip. Repeat on the lower-left side. To release the top clips, you may need to release the lower clips of the radio bezel by inserting the hook tool in the lower-right and left corners of the radio and pulling back. Carefully release the top clips of the air vent module. Disconnect the clock wiring and set the unit aside.

Step 2: Mount Installation

On the inside-right of the center console, locate a flat area below the radio bezel. Place the Custom Bezel Mount in position. Insert one self-tapping screw into the lower hole of the mount and tighten. Pivot the mount to the desired angle and insert the remaining screws, then tighten.

Step 3: Reassembly

Carefully reinstall the dash in reverse order. Install any Bracketron phone holder or AMPS compatible device to your Custom Bezel Mount. Installation is complete.

Lexus LS430 (2001-2006) & ES300 (2002-2005)

Note: Read instructions completely before installing. Exercise caution, wood grain panels scratch easily.

Tools Needed: #2 Phillips screwdriver, clean cloth, 10 mm socket and driver, 5/64" drill bit and drill, hook tool, marking pen.

Parts Included: One phone mount, instructions, three (3) #8 x 1/2" screws.

Location of Mount: To the Right of the Radio.

Step 1: Panel Removal

Cover the gearshift lever with a cloth. Remove the lower panel holding the seat heater controls by inserting the hook tool behind it and gently pulling to release two clips. Unplug the wiring connector and set the panel aside. Remove the three Phillips screws exposed. Open the CD player panel by pushing on it, then release two clips using the hook tool in the left and right corners. Slide the panel off, unhook the wiring harness, and set it aside.

Step 2: Radio Removal

Caution: Do not disconnect any wires to the radio! Remove the two 10 mm bolts at the base of the radio. Place your hand under the radio and pull it towards you; two clips (middle left and right) should release. Set the radio aside.

Step 3: Mount Installation

Place the Custom Bezel Mount against the dash pad. Using the mount as a template, mark the three screw hole locations. Drill three pilot holes using a 5/64" drill bit (do not drill deeper than 1/4"). Align the mount over the pilot holes and insert and tighten the three #8 x 1/2" screws.

Final Steps

Re-assemble the dash in reverse order, securing all screws and clips. Install any Bracketron phone holder or AMPS compatible device to your Custom Bezel Mount. Installation is complete.

Lexus ES300 (2002-2005) - Alternate Location

Note: Read instructions completely before installing. Exercise caution, wood grain panels scratch easily.

Tools Needed: Hook tool, #2 Phillips screwdriver, clean cloth, 5/64" drill bit, drill, marking pen.

Parts Included: One phone mount, instructions, three (3) #8 x 1/2" screws.

Location of Mount: To the right of Climate Control.

Step 1: Gear Shift Bezel Removal

Cover the gear shift lever with a cloth. Set the parking brake and shift to neutral. Use the hook tool to remove the gear shift bezel by inserting it behind the lower left corner and gently pulling up to release a retainer clip. Work the tool around the bezel to release all eight clips. Lift the trim bezel over the gearshift and set aside. Do not disconnect wiring harnesses.

Step 2: Climate Control Module Removal

Remove the climate control module, fastened by five clips (one in each corner and one at the top center). Insert the hook tool behind the lower left corner and pull towards you to release a clip. Work the tool around the module to release all clips. Pull the module out and set aside. Do not disconnect the wiring harness.

Step 3: Mount Installation

Place the Bezel Mount against the dash pad, aligning it with the bottom of the Radio module. Using the mount as a template, mark the three screw hole locations. Drill three pilot holes using a 5/64" drill bit (do not drill deeper than 1/4"). Position the Bezel Mount over the pilot holes and insert and tighten the three #8 x 1/2" screws.

Final Steps

Re-assemble the dash in reverse order, securing all screws and clips. Shift to park and release the parking brake. Install any Bracketron phone holder or AMPS compatible device to your Bezel Mount. Installation is complete.

Toyota Camry (2002-2006)

Note: Read instructions completely before installing. Exercise caution when handling plastic parts.

Tools Needed: Dash Trim Tool (Part #SIT-104), #2 Phillips Screwdriver, marking pen, 5/64" drill bit and drill, sharp razor blade utility knife.

Parts Included: Two (2) #8x3/4" self-tapping screws.

Location of Mount: To the right of the radio.

Step 1: Climate Control Removal

Insert the Dash Trim Panel Tool between the climate control and radio bezel on the right side. Gently pull out the lower climate control, releasing a retainer clip. Continue working the climate control loose, releasing three more clips (two on each side, totaling four). Let the climate control hang to the left.

Step 2: Radio Bezel Removal

Insert the Dash Trim Panel Tool behind the bezel surrounding the radio in the upper-right corner. Pull back to release the top-right clip. Repeat in all four corners (two top, two bottom) to release the bezel. Prop the radio bezel onto the top of the dash. No need to disconnect wiring.

Step 3: Dash Pad Modification and Mount Installation

Locate a small piece of dash pad to the right of the climate control and radio bezel retaining clip holes. Carefully shave this pad off cleanly with a sharp razor blade. Place the Bezel Mount in the cavity just above the seam. Mark two spots for pilot holes, avoiding the top hole on the Bezel Mount. Remove the mount and drill two pilot holes into the solid plastic behind the dash pad (do not drill deeper than 1/4"). Use extreme caution as the dash pad can tear easily. Position the Bezel Mount over the pilot holes and insert and tighten the two provided screws with a Phillips screwdriver.

Final Steps

Carefully reinstall the dash in reverse order. Install any Bracketron phone holder or AMPS compatible device to your Bezel Mount. Installation is complete.

Saab 9-5 Sedan & Wagon (1999-2005)

Note: Read instructions completely before installing. Exercise caution when handling plastic parts.

Tools Needed: Ford DIN Tool (SIT-101), Dash Trim Tool (SIT-104), #2 Phillips Screwdriver, 5/64" drill bit, drill, marking pen.

Parts Included: One CBM, instructions, Two (2) #8 x 1/2" screws.

Location of Mount: To the right of Climate Control.

Step 1: Radio Removal

Insert two DIN tools (SIT-101) into the four holes in the radio face until they click. Gently pull the radio out by applying outward pressure to the DIN tools. Set the radio aside carefully.

Step 2: Climate Control Removal

Use the Dash Trim Tool (SIT-104) to gently insert to the right of the climate control. Pry slightly to release two small plastic clips from each side of the radio area. Do not disconnect wires from the climate control. Place climate control aside on a soft surface.

Step 3: Mount Placement

Locate a spot to the right of the climate control cavity for the Custom Bezel Mount. Align the mount towards the bottom of the cavity to allow room for the radio. Mark two hole locations, using the bottom two holes and not the top hole.

Step 4: Mount Installation

Drill two pilot holes at the marks using a 5/64" drill bit (do not drill deeper than 1/4"). Position the Custom Bezel Mount over the pilot holes and insert and tighten the two #8 x 1/2" screws.

Step 5: Reassembly

Re-assemble the dash in reverse order, securing all screws and clips. Install any Bracketron phone holder or AMPS compatible device to your Custom Bezel Mount. Installation is complete.

Ultra Slim Swivel Installation

Note: This mount is designed for Satellite Radio Car Kits requiring extra clearance for plug & play connections. It offers adjustability for devices like Satellite Radio Receivers, GPS monitors, or Mobile Phones, tilting approximately 15° in all directions and swiveling 360°.

Parts Included: Ultra Slim Swivel, AMPs Adapter Plate, M4x10 Hex Head Screws (4), M4x10 Pan Head Screws (4), M4x12 Pan Head Screws (4), M4 Hex Head Nuts (4), M4 Nylon Locking Nuts (4), M4 Star Washers (4), Full Color Instruction Sheet.

Tools Needed: 9/32" open end wrench, #2 Phillips Screwdriver.

Location: Attach to any AMPs compatible mounting device.

Step 1: Swivel Attachment to Mount

Attach the Ultra Slim Swivel to a Bracketron Custom Bezel Mount or other AMPs mounting device. Insert M4x10 Pan Head screws through the back half of the swivel and align with the mount holes. Attach M4 Nylon Locking Nuts finger tight. Rotate the front half of the swivel to access screws. Tighten all 4 screws with a #2 Phillips screwdriver and 9/32" wrench. Tighten the center screw for desired swivel tension.

Step 2: For T-Notch Devices

Attach the AMPs T-Notch Adapter to the front half of the swivel using M4x12 Pan Head screws. Attach M4 Star Washers and M4 Hex Nuts to the screws and tighten with the #2 screwdriver and 9/32" wrench. Slide your device onto the T-notch Adapter plate to secure it.

Step 3: For AMPs Devices with Inserts

Attach your AMPs device using M4x10 Hex Head screws and M4 Star Washers. Align device holes with swivel holes. Slide Star Washers onto Hex Head screws. Insert screws through the swivel into the device finger tight. Tighten the device with the 9/32" wrench. Your device is now secure.