maxspect Jump Series LED Lighting System User Manual

User Manual for maxspect models including: 2AM68MJ-LED, 2AM68MJLED, Jump Series LED Lighting System, Jump Series, LED Lighting System, Lighting System, System

FtpDown

User manual

Guangzhou Maiguang Electronic Science Technology Co.,Ltd. MJ-LED Maxspect Jump Series LED Lighting System 2AM68MJ-LED 2AM68MJLED mj led

File Info : application/pdf, 10 Pages, 669.92KB

GetApplicationAttachment.html?id=7973388

User Memo
Dear Customer,
Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully.
User Memo:
Date of purchase:
Dealer name:
Dealer address:

Dealer website: Dealer email:
Dealer phone no.:

Please visit us on Facebook, Twitter or Instagram!

Facebook

Twitter

Instagram

Package Content
Please check the content in the package.
EN

supports 8-20mm glass. Use the pad while mounting the device on 6mm glass tank.

Precautions

Before using the MaxspectTM Jump Series LED Lighting System, please read
these operating instructions carefully. Take special care to follow the safety
suggestions listed below. Afterwards keep this manual handy for future
reference.
1. Remove any plastic bags and packaging material protecting the fixture. 2. Never look directly at the LED bulbs when you switch on the system. Incorrect use of
this apparatus will increase eye hazard.
On Safety
1. Power Source Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
2. Power Cord Protection The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Never take hold of the plug or cord if your hand is wet, and always grasp the plug body when connecting or disconnecting it.
3. Installation Install indoor only, and use the attachments, mounting frames, hanging kit and accessories provided and specified by the manufacturer.
On Operation
1. Operation Always follow the operation instructions set forth in this manual when using the MaxspectTM Jump series LED Lighting System.
2. Heat The apparatus should be situated away from heat sources such as radiators, and do not expose to excessive heat such as sunshine, fire or the like.
3. Moisture To reduce the risk of fire or electric shock, do not expose this apparatus to rain, moisture, dripping or splashing.
4. Ventilation The apparatus should be situated so that its location or position does not interfere with its proper ventilation.
5. Magnetism The apparatus should be situated away from equipment or devices that generate strong magnetism.
6. Cleaning Clean only with dry or damp cloth.
Waste Disposal
1. Product: Electronic devices are recyclable waste and must not be disposed of in the household waste. At the end of its service life, dispose of the product according to the relevant statutory regulations. Remove any inserted (rechargeable) batteries and dispose of them separately from the product.
2. (Rechargeable) batteries: You as the end user are required by law (Battery Ordinance) to return all used batteries/rechargeable batteries. Disposing of them in the household waste is prohibited. Used (rechargeable) batteries can be returned to collection points in your municipality or wherever (rechargeable) batteries are sold. You thus fulfil your statutory obligations and contribute to the protection of the environment.
3. As a producer in terms of the German ElektroG we are registered with the German registration authority Stiftung Elektro-Altgeräte-Register (Nordostpark 72, 90411 Nürnberg), having been granted the following WEEE registration number: DE21010727.

Installation Instruction

Mounting the LED Lighting System
Before connecting the fixture to power, first mount the system by using the provided stand.

1
3

2
4

Scan the QR code to check out the detailed
installation video.
4

Adjust the angle by tweaking the screws.

Installation Instruction
Hanging Kits Installation (sold separately)
EN
Scan QR code to check out the detailed installation video.
5

Operation Instruction

SYNA-G CLOUD APP
MaxspectTM Jump series LED Lighting System is an APP controlling system. To get full access to the fixture, please scan below QR-Code to install SYNA-G CLOUD APP on your mobile device.

iOS

Android

Operation

Fixture

Different color of the Indicator represents different working mode of the device. Scan the

above QR code to check out the detailed operation instructions on YouTube.

Off: No Wi-Fi connection On: Wi-Fi connected
Flashes: Wi-Fi connecting
Left Button

ON/OFF Button

Yellow: Manual Mode Blue: Auto Mode
Right Button

Default Factory Setting: Manual Working Mode, all channels 100% brightness.

Press and hold Button for about 5s can turn ON/OFF the device.

Press and hold and buttons for about 3s to turn the device into Wi-Fi connection

status.

indicator starts to flash, the buzzer sounds 0.2s. After Wi-Fi is connected, the

indicator is constant on and the buzzer sounds 0.4s.

While in the Manual Mode, press button can switch between brightness and color

temperature settings, then press and buttons can adjust the settings.

While in the Auto Mode, press and buttons can adjust the color temperature.

In normal working status, press and hold button for about 5s until indicator quick flashes for 3 times and the buzzer sounds 0.4s, the lighting settings are being recovered to the default factory setting (WiFi connection remains valid).

Operation Instruction

Ways of Connection
User only gets limited access to the device through the Direct Connection. To get full access to the device, please connect it to the Internet.

Function
Auto Working Mode
Manual Working Mode Color Temperature Setting Illumination Setting Saving Acclimation Mode Multiple Fixtures Controlling Fixture Grouping
Fixture Naming
Global Control Illumination Setting Sharing

Wi-Fi Connection (with Internet)

Wi-Fi Connection (without Internet)
x x

Direct Connection
x x x x x x

Maintenance Instruction

Maintenance of the fixture
User must periodically perform maintenance on the fixture, including but not limited to the following steps: · Use a damp cloth to clean the acrylic lens to make sure it is not covered by salt creep or
other dirt and debris. Uncleaned lens will severely affect the luminous output of the fixture, so for best performance you should clean the lens once a week. · Clean the dust and debris trapped in the fan units. Regularly and properly cleaned fans will last much longer than those that are not. Fan unit is wear-and-tear parts and must be replaced every 24-36 months depends on the frequency of maintenance performed on them. · Clean / remove any salt creep or dirt and debris that had been built up or collected on the aluminum body of the fixture, as they may affect the dissipation of heat from the fixture. Note: Failure to perform the above-mentioned maintenance on the fixture may cause unnecessary damage to your fixture and may void your warranty!
Specifications
For the latest specifications on LED layout, types and color spectrum, please visit our website www.maxspect.com, or scan below QR-Code.

Limited Warranty

Maxspect (Hong Kong) Limited warrants all MaxspectTM Jump series LED Lighting System products against defects in workmanship for a period of 12-months from the date of purchase. If a defect exists during the warranty period, Maxspect (Hong Kong) Limited at its option will either repair (using new or remanufactured parts) or replace (with a new or remanufactured unit) the product at no charge.
THE WARRANTY WILL NOT APPLY TO THE PRODUCT IF IT HAS BEEN DAMAGED BY MISUSE, ALTERATION, ACCIDENT, IMPROPER HANDLING OR OPERATION, OR IF UNAUTHORIZED REPAIRS ARE ATTEMPTED OR MADE. SOME EXAMPLES OF DAMAGES NOT COVERED BY WARRANTY INCLUDE, BUT ARE NOT LIMITED TO, USING AFTER-MARKET LED BULBS AND MODIFICATION OF THE CIRCUITRY, WHICH ARE PRESUMED TO BE DAMAGES RESULTING FROM MISUSE OR ABUSE.
DISCLAIMER OF CONSEQUENTIAL AND INCIDENTAL DAMAGES:
You and any other user of Maxspect (Hong Kong) Limited products shall not be entitled to any consequential or incidental damages, including without limitation, loss of use of the unit, inconvenience, damage to personal property, phone calls, lost income or earnings. This warranty gives you specific legal rights and you may have other rights, which vary from state to state.
MAXSPECT LTD. MAKES NO WARRANTY OR REPRESENTATION, EITHER EXPRESS OR IMPLIED, WITH RESPECT TO THE PRODUCT'S QUALITY, PERFORMANCE, MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE. AS A RESULT, THIS PRODUCT, IS SOLD "AS IS," AND YOU THE PURCHASER ASSUME THE ENTIRE RISK AS TO ITS QUALITY AND PERFORMANCE.
IN NO EVENT WILL MAXSPECT LTD, BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY DEFECT IN THE PRODUCT OR ITS DOCUMENTATION.
The warranty, disclaimer, and remedies set forth above are exclusive and replace all others, oral or written, expressed or implied. At no time will any Maxspect (Hong Kong) Limited dealers, agents, or employees be authorized to make any modifications, extension, or addition to this warranty.
Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you.

FCC St at ement This equipment has been t est ed and found t o comply w it h t he limit s for a Class B digit al device, pursuant t o part 15 of t he FCC Rules. These limit s are designed t o provide reasonable prot ect ion against harmful int erference in a resident ial inst allat ion. This equipment generat es, uses and can radiat e radio frequency energy and, if not inst alled and used in accordance w it h t he inst ruct ions, may cause harmful int erference t o radio communicat ions. How ever, t here is no guarant ee t hat int erference w ill not occur in a part icular inst allat ion. If t his equipment does cause harmful int erference t o radio or t elevision recept ion, w hich can be det ermined by t urning t he equipment off and on, t he user is encouraged t o t ry t o correct t he int erference by one or more of t he follow ing measures:
·Reorient or relocat e t he receiving ant enna. ·Increase t he separat ion bet w een t he equipment and receiver. ·Connect t he equipment int o an out let on a circuit different from t hat t o w hich t he receiver is
connect ed.
·Consult t he dealer or an experienced radio/ TV t echnician for help. Caut ion: Any changes or modificat ions t o t his device not explicit ly approved by manufact urer
could void your aut horit y t o operat e t his equipment . This device complies w it h part 15 of t he FCC Rules. Operat ion is subject t o t he follow ing t w o condit ions: (1) This device may not cause harmful int erference, and (2) t his device must accept any int erference received, including int erference t hat may cause undesired operat ion.
RF Exposure Informat ion This equipment complies w it h FCC radiat ion exposure limit s set fort h for an uncont rolled environment . This equipment should be inst alled and operat ed w it h minimum dist ance 20cm bet w een t he radiat or and your body.

References

Microsoft Word 2019