Door Delete Kit for Jeep Step Sliders!
This manual provides instructions for installing the Rock-Slide Engineering Door Delete Kit for Jeep Step Sliders.
Parts Included:
| Description | Quantity |
|---|---|
| Jeep Door Delete Bracket | 2 |
| Door Delete Buttons | 2 |
| Door Delete Harness | 2 |
| BLACK-Oxide Alloy Steel Flanged Button Head Screw | 2 |
| Nut, Nyloc, 10-32 Zinc Plated Steel | 2 |
Tools Required:
- Allen Wrench
IMPORTANT: Kill the power to your Step Sliders by turning off the rocker switch. Ensure they remain closed for Door Delete Installation.
Step 1: DOOR DELETE INSTALLATION
For JL/JT Models: Move your front seat as far back as it will go to expose the hole on the seat rail. Small holes on the top of the bracket will be used to secure it into place. One bracket per side.
[Image: Close-up of a Jeep JL/JT seat rail showing the mounting hole location and a bracket being attached.]
For JK Models: Install using the middle hole on the seat rail. Use the small hole on the front of the bracket to secure into place.
[Image: Close-up of a Jeep JK seat rail showing the mounting hole location and a bracket being attached.]
Tighten the brackets using the button head screw and steel nut. Repeat on the driver and passenger side.
Step 2:
Thread the door delete harness with the spade connectors through the bracket. Connect each side to the door delete button and snap it into place. Red and black wires can be plugged in on either side of the button.
[Image: The door delete harness being threaded through the bracket and spade connectors being attached to the door delete button.]
Step 3:
Remove rocker panels to expose your door sensor/harness connectors and disconnect them. Run the door delete harness along the edges or underneath your carpet to your connectors (refer to Step 2 images for routing). For 4-door models, bring one side of the harness to the front under the plastics and thread the other to the rear. For 2-door models, tuck the remaining harness under plastics. Clip both connectors together, one into the sensor and one into the harness. Replace plastics and repeat on both sides.
Return power to the steps with the rocker switch.
YOU ARE DONE! ✔️
[Image: Close-up showing the process of disconnecting the original vehicle harness and connecting the new door delete harness.]
WARRANTY POLICY
LIMITED TWELVE (12) MONTH WARRANTY FOR FINISH AND ELECTRICAL COMPONENTS
Rock-Slide Engineering, LLC (“RSE”) warrants to the original purchaser that (a) the structural and mechanical components of the Step Sliders will be free of defects in material and workmanship for the lifetime of the Step Sliders (the “product”), and (b) the finish (powder coat) and the electrical components (including the motor) will be free of defects in material and workmanship for a period of twelve (12) months from the original date of purchase. This warranty applies only to the original retail purchaser. Warranty is void if product was not purchased directly from R-SE or from an authorized RSE retailer or reseller. This warranty applies only with regard to the product as originally installed to the original vehicle. This warranty does not cover removal or reinstallation of the product.
To exercise this warranty and receive any warranty service, the original purchaser must provide RSE with proof of purchase and date of purchase that is acceptable to RSE, such as a copy of the original purchaser's purchase receipt. The original purchaser must return the defective product to RSE along with a description of the problem, a copy of the original purchase receipt, the original bill of sale and all contact information (name, address, telephone number and email address). To begin the warranty process, the original purchaser must email RSE's warranty department. During this warranty term, and upon the original purchaser's valid exercise of this warranty, RSE shall, at its option, repair or furnish the replacement product in the event the original product is deemed by RSE to be defective. RSE's sole liability shall be for repairing or replacing the product, but RSE may refund the purchase price at its sole discretion and option. The original purchaser is responsible for prepayment of all shipping and/or transportation charges with respect to the exercise of this warranty. The product may change without notice. In the event of a product change, RSE has no obligation to upgrade or modify any older generation product.
THE WARRANTY SET FORTH HEREIN IS THE ONLY WARRANTY COVERING THE PRODUCT. NO OTHER WARRANTY EXISTS, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE. No retailer, reseller, dealer, agent, or employee is authorized to make any modifications, extensions, amendments, or additions to this warranty.
This warranty shall be void in its entirety if RSE determines that the product installation was modified, changed, altered, customized or in any way used other than as instructed. Installation of the product without strictly adhering to the installation instructions shall void this warranty. Installation must be on the proper vehicle or warranty is void.
RSE SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, UNDER ANY LEGAL THEORY AND/OR UNDER ANY CIRCUMSTANCE WHATSOEVER. IN ANY EVENT, ANY DAMAGES IN ANY SITUATION SHALL BE LIQUIDATED DAMAGES AND MAY NOT EXCEED THE RETAIL PRICE OF THE PRODUCT. RSE SHALL NOT BE LIABLE FOR ANY LOSS, DAMAGE OR INJURY DIRECTLY OR INDIRECTLY ARISING FROM THE USE OF OR INABILITY TO DETERMINE THE USE OF THE PRODUCT. THE ORIGINAL PURCHASER IS RESPONSIBLE TO DETERMINE THE SUITABILITY OF THE PRODUCT FOR ITS INTENDED USE, PRIOR TO USING THE PRODUCT, AND THE ORIGINAL PURCHASER ASSUMES ALL RESPONSIBILITY AND RISK IN CONNECTION THEREWITH.
For questions or concerns: please contact our office at 435-752-4580 and ask for the warranty department or email us at warranty@rockslideengineering.com.
mailto:warranty@rockslideengineering.com
Home - Rock Slide Engineering
