AquaAmp Waterproof Wireless Chargers
AquaAmp Waterproof Wireless ChargersAquaAmp Waterproof Wireless Chargers
Installation Guide for AquaAmp models including: P1017A-1, 2A64N-P1017A-1, 2A64NP1017A1, FL 33755 Core Lite Wireless Charger, FL 33755, Core Lite Wireless Charger, Lite Wireless Charger, Wireless Charger, Charger
AQUA-AMP, LLC P1017A-1 Core Lite Wireless Charger 2A64N-P1017A-1 2A64NP1017A1 p1017a 1
File Info : application/pdf, 2 Pages, 499.89KB
DocumentDocumentElectrical Information & Installation Instructions The product must be installed according to the specified instructions. Failure to comply may result in personal injury, vessel/vehicle damage, and/or product failure. Installation by a trained electrician is recommended by AquaAmp. Damage and/or injuries caused by improper installation are not covered by the warranty. WARNING: Only a 12V DC battery/power supply should be used with this device. Before installing, the power supply must be turned off. Between the battery/power supply and the product, an appropriate fuse or circuit breaker must be utilized. Before turning on the electricity, double-check that all wiring is polarized correctly. High voltages may be included in this product. Do not alter the product in any way. This product is not intended for use in potentially hazardous or flammable environments. Do not install in a hazardous/flammable environment, such as engine rooms. Make sure the space behind the mounting point is clear of wires, fuel, and any other potentially hazardous things before drilling any holes. Ensure that any holes cut do not considerably degrade the surface's structure. If the product must be installed outside, it must be installed safely above the waterline and not in danger of being submerged. A metallic surface prevents the product from charging. CAUTION: The item is designed to charge Qi compatible devices only. The cable must be kept in place and not obstruct mechanical systems. There are no user-serviceable components in this product. In no way attempt to repair or modify the product. The device's high friction top surface does not guarantee that it will not slip during strong acceleration and deceleration working situations. A phone case thicker than 3mm may prevent the smartphone from charging. The product may temporarily shut down if used in a hot environment or in direct sunlight; this is a safety feature of the electronics. The IP rating is only valid if the instructions are followed correctly. Avoid mounting near heat-radiating appliances and in poorly ventilated spaces when choosing a placement. EMC INSTALLATION GUIDELINES: To ensure that electromagnetic interference between equipment is minimized, AquaAmp devices comply with Electromagnetic Compatibility (EMC) requirements. To keep electromagnetic interference to a bare minimum, proper installation is essential. WIRING: When extending the wire from your battery/power source to the product, make sure there is a continuous supply of at least 10V. For any length of cable extension, we recommend an 18AWG (0.82mm2) wire gauge. This diagram shows how the product should be linked to a 12V or 24V DC battery or power supply. ENVIRONMENTAL PROTECTION: Electrical trash should not be thrown out with household garbage. Please recycle wherever possible. For recycling advice, contact your local government or a merchant. IMPORTANT: AquaAmp LLC disclaims all liability for any injuries or other damages resulting from the use of their products in any situation. WARRANTY: The non-transferable 2-year warranty covers only this AquaAmp product and not any devices mounted in or on it. Users' devices are not covered by a guarantee, and they subject them to known and unknown hazards at their own risk. FCC WARNING: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user's authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. To maintain compliance with FCC's RF exposure guidelines, the distance must be at least 20 cm between the radiator and your body, and fully supported by the operating and installation configurations of the transmitter and its antenna(s) AquaAmp LLC certifies that this product complies with the EMC CE-RED Directive (2014/53/EU) and the EN 62368 standard. The CE compliance certificate can be accessed at aquaamp.com. Contact: orders@aquaamp.com 1108 Eldridge St, Clearwater, FL 33755 For further information visit www.aquaamp.com Installation Instructions: Core Lite Wireless Charger Parts Provided Wireless Charger Tools Required 2.5" Hole Saw Electric Drill Technical Information Input Voltage Range 12V DC Max Current Draw Output Power Standby current Draw 2A 10W < 0.1W Waterproof rating IPx6 front and back Certifications Qi, CE, FCC, RoHS Step 1: Drill or Cut 2.5" hole. Installation Guide Step 3: Using a 2A fuse, attach wires to a 12v power supply and ensure there is a waterproof connection. Step 2: Use an alcohol wipe to clean application surface. Remove adhesive backing from the wireless charger and insert the charger into hole. Step 4: Make sure the charger was installed correctly by placing a wireless charging compatible device in the center of the charger. Check that the device is charging a few seconds after it is placed. Contact: orders@aquaamp.com 1108 Eldridge St, Clearwater, FL 33755 For further information visit www.aquaamp.com