S-TRACK OSTRICH XDO22 2CH Analog Output Adapter

Preface

Thank you for choosing our product. This product provides the interfacing between analog inputs and Dante channels, requiring power over Ethernet (POE) switch for power supply.

Caution

To ensure the reliable use of the equipment and the safety of personnel, please observe the following matters during installation, use and maintenance:

1. When installing the equipment, make sure that the ground wire in the power line is well grounded and the chassis grounding point is well grounded.
2. Keep the working environment well ventilated so that the heat generated by the equipment at work can be discharged in time to avoid damage to the equipment due to high temperature.
3. Turn off the main power supply of the equipment when it is not in use for a long time or in a humid and dewy environment.
4. Be sure to unplug the AC power cord of the equipment from the power outlet before the following operations:
   • A. Remove or reinstall any part of the equipment.
   • B. Disconnect or reconnect any electrical plugs or connections to the equipment.
5. Do not disassemble the equipment without permission by non-professionals to avoid the risk of electric shock. Do not repair the equipment privately to avoid aggravating the damage.
6. Do not spill any corrosive chemicals or liquids on or near the equipment.

Chapter 1 Product Introduction

1.1 Introduction

This product is an audio interface device based on the internationally recognized Dante protocol, capable of converting analog audio signals into digital ones and routing them through the Dante protocol to any Dante audio transmission network device. It offers high-quality, long-distance transmission, low latency, strong anti-interference ability, and convenient networking capabilities. The device utilizes high-quality AD/DA conversion chips, bridging your analog devices and more into the world of networked audio.

1.2 Functions

• Support two Dante network audio signal access, two analog audio signal output;
• Two XLR female connectors for analog audio inputs;
• 1 RJ45 network interface connected to a PoE Switch for receiving Dante network audio signals;
• Convert Dante network audio signal to analog audio signal output;
• Displays the device name and IP address;
• Supports 802.3af and 802.3at PoE power supply;
• Simple audio routing, configure audio routing through Dante Controller.

Chapter 2 Specification

Chapter 3 Interface Description

The OSTRICH XDO22 features the following interfaces:

• 1: Dante network interface with PoE supply.
• 2: Analog output 1.
• 3: Analog output 2.
• 4: Display: Shows the IP address.

(Diagram Description: The diagram shows three views of the device. The left view shows two XLR connectors labeled OUT CH1 and OUT CH2. The middle view shows the top of the device with the Dante logo and the product name "OSTRICH XDO22 2CH ANALOG OUTPUT ADAPTER". The right view shows the rear of the device with an RJ45 network connector labeled "DANTE".)

Chapter 4 Dante Network Audio Routing

In a Dante audio network, the Dante Controller software is required to set up the routing of the various signals accessing the processor. It can realize 1-to-1, 1-to-N mapping operation from input to output within Dante network.

Note:

• Dante can not run in a Wi-Fi wireless connection environment; it is dependent on a reliable and secure wired network environment to transmit perfect audio.
• Dante Controller software corresponds to the platform of Windows 7, Windows 10, Windows 11, and macOS. Please select the appropriate software version according to your system platform.

Click to download the official Dante Controller software: Dante Controller

(Diagram Description: A screenshot of the Dante Controller software interface is displayed, showing network devices, transmitters, receivers, and status information.)

Warranty Regulations

The warranty period of this product is 1 year.

In the warranty period, non-man-made damage caused by product performance failure can enjoy three packages of service.

Warranty card must be stamped by the sales unit after the effective date. Alteration is invalid!

The following conditions (including, but not limited to, this) are not covered by the three-package service:

1. No warranty card or missing valid invoice, or the date has exceeded the validity period of the three packages of services.
2. Not in accordance with the requirements of the product instructions for use, maintenance, management, and damage caused.
3. The product model or code on the warranty voucher does not match the physical goods.
4. Damage caused by the dismantling and repair by non-authorised service providers.
5. Normal discolouration, wear and tear, and consumption during the use of the product are not covered by the warranty.
6. The product cannot be used due to the user's own network reasons; please consult customer service staff.

Company Information

SHENZHEN S TRACK SCIENCE TECHNOLOGY CO., LTD

Web: www.s-track.com.cn

Tel: +86 755 29983191

Mail: service@s-track.cn

Add: 9F, 1B, Shangzhi Technology Park, Guangming District, Shenzhen City, Guangdong Province, China 518107