NETGEAR Powerline AV 500 WiFi Access Point XWNB5602 Installation Guide

Box Contents

The box typically contains:

• 1x Powerline 500 PassThru Adapter (XAV5401)
• 2x Ethernet Cables
• 1x Powerline 500 WiFi Access Point (XWN5001)

Note: Adapters may vary by region. NETGEAR recommends not plugging a Powerline device directly into an electrical extension cord.

Hardware Features

Powerline 500 PassThru Adapter (XAV5401)

• 1. Filtered Outlet
• 6. Security Button
• 7. Reset Button
• 8. Ethernet Port

Powerline 500 WiFi Access Point (XWN5001)

• 2. Power LED
• 3. Powerline LED
• 4. Ethernet LED
• 5. Wireless LED
• 9. Power Button (Device On/Off)

LED Indicators

• Power LED: Green when the adapter is plugged in. Turns orange in power-saving mode if the Ethernet port is inactive for over 10 minutes.
• Ethernet LED: Illuminates green when an active Ethernet-connected device is detected. Off if there is no Ethernet connection.
• Wireless LED: Illuminates green when the wireless radio is enabled.
• Powerline LED: Illuminates when the adapter detects at least one other compatible Powerline device. Colors indicate connection speed: Green (>80 Mbps), Orange (50-80 Mbps), Red (<50 Mbps).

Button Descriptions

• Reset Button: Press and hold for 2 seconds to restore factory default settings.
• Power Button: Turns the device on or off.
• Security Button: Used to secure the Powerline network and connect wireless devices to the XWN5001.

Setting Up Your Powerline Network

1. Plug each Powerline adapter into a wall socket.
2. Secure your Powerline network:
   • Ensure the Power LED on each adapter is solid green.
   • Press the Security button on the XAV5401 for 2 seconds, then release. The Power LED will blink green during pairing.
   • Within 2 minutes, press the Security button on the XWN5001 for 2 seconds, then release.

After a few seconds, the security is set, and the Power LED will be solid green, allowing secure communication between Powerline adapters.

Warning: Only press the Security button when the Power LED is solid green. Pressing too early may temporarily disable Powerline communication. Use the Reset button to restore defaults if this occurs.

3. Plug the XAV5401 into a wall socket near your router or gateway.
4. Connect the XAV5401 to the router or gateway's network port using an Ethernet cable.
5. Plug the XWN5001 WiFi Access Point into a wall socket in a room where Wi-Fi coverage is needed.

Note: The XWN5001 has an additional Ethernet port to connect wired devices like gaming consoles or Blu-ray players to your network.

Configuring Wi-Fi Access on Your XWN5001

You can configure Wi-Fi access using NETGEAR genie or the browser setup guide.

Using NETGEAR genie:

1. Install NETGEAR genie (see "Installing NETGEAR genie" section).
2. Temporarily connect your computer directly to the XWN5001 via Ethernet.
3. Launch NETGEAR genie and click on Network Map.
4. Click the Powerline icon on the Network Map screen.
5. Right-click the XWN5001 icon and select Wireless Configuration from the context menu.

Note: For advanced wireless settings, double-click the device icon and select the IP address. Default login is admin/password.

Enter the following wireless settings:

• Wireless network name (SSID)
• Wireless security type
• Passphrase

Example settings: SSID: Netgear_EXT, Security Type: None.

If a NETGEAR router is on your network, the setup wizard can quickly configure the XWN5001 as a wireless accelerator. Alternatively, for advanced setup, click the provided link to access the XWN5001's web page.

You can either clone your existing wireless network by entering the same settings as your router/gateway, or create a new wireless network for a second Wi-Fi zone in your home.

8. Click Apply to save changes.
9. Disconnect the Ethernet cable from the XWN5001 when finished.

You can now connect your wireless devices to the XWN5001. Refer to the "Connecting to the XWN5001 Access Point" section.

Using the Browser Setup Guide:

1. On your computer or wireless device, connect to the XWN5001's wireless network. The default SSID is NETGEAR_EXT. The default network key (password) is printed on the back of the XWN5001.
2. Open a web browser and navigate to www.mywifiext.net or www.netgearextender.net.
3. Log in using username: admin and password: password.

The browser setup guide allows you to configure the XWN5001's wireless settings. You can clone your existing network settings or create new ones.

You can note your new wireless settings below:

• Wireless network name (SSID):
• Network key (Passphrase):

You can now connect your wireless devices to the XWN5001. Refer to the "Connecting to the XWN5001 Access Point" section.

Connecting to the XWN5001 Access Point

Manual Connection:

1. On your computer or wireless device, launch the wireless connection management utility.
2. Connect to the XWN5001 wireless network (SSID).
3. Enter the network key (passphrase).

Your wireless device is now connected to the XWN5001 and you can browse the web.

Automatic Connection using WPS Button:

1. Press and hold the Security button on the XWN5001 for approximately 2 seconds, then release. The Wireless LED will start blinking.
2. Press the WPS button on your wireless device for 2 seconds, then release.

When the Wireless LED stops blinking, your wireless device is automatically connected to the XWN5001, and you can browse the internet.

Installing NETGEAR genie

1. Go to http://support.netgear.com in your browser's address bar.
2. Click the For Home button.
3. In the search field, enter xwn5001.
4. Download the NETGEAR genie version compatible with your operating system (Windows or Mac).
5. Run the downloaded file and follow the on-screen instructions to install NETGEAR genie.

Compatible NETGEAR Powerline Devices

Your Powerline devices can share a Powerline network with compatible NETGEAR devices including: XAVB1301, XAVB1401, XAVB2101, XAVB2602, XAVNB2001, XAVB5601, XAVB5101, XAVB5201, XAVB5602, XAUB2511, XAVB5004, XAVB1004, XAVB5401, XWNB5201, and XWNB1601.

For a complete list of HomePlug AV certified devices, visit www.homeplug.org/certified_products.

Safety Information

• AC Power Outlet Rating: 100 to 240V, 16A
• Output Power Rating: 250V, 16A (max.)
• Operating Temperature: 0 to 40°C
• Check the electrical load for each device plugged into a filtered outlet. Adhere to the product and home's rated capacity and electrical requirements.
• The power outlet should be installed near the equipment and be easily accessible.
• Only power cords are permitted in the filtered outlet. No other direct-plug-in equipment is allowed. Power cords should be a maximum of 1m long and have a minimum cross-sectional area of 0.75mm².
• Do not plug devices exceeding the rated capacity into the XAV5401's filtered outlet. The output voltage of the filtered outlet must be the same as the input voltage of the XAV5401. Ensure connected devices are electrically configured to operate with the available current in your region to avoid system damage.
• If the input voltage is less than 100V AC, the device plugged into the XAV5401's filtered outlet may not operate optimally.
• DO NOT plug large home appliances into the filtered outlet or a connected extension cord. The device is not designed for use with household appliances such as air conditioners, power tools, heaters, fans, hair dryers, ovens, or refrigerators.

Support

Thank you for purchasing this NETGEAR product. After installation, note the serial number from your product label. You will need it to register your product at https://my.netgear.com. Product registration is required before using NETGEAR phone support. NETGEAR recommends registering your product on the NETGEAR website.

For updates, additional documentation, and support for NETGEAR products, visit http://support.netgear.com. NETGEAR recommends using only official NETGEAR support resources. The user manual is available online at http://downloadcenter.netgear.com or via a link within the product's user interface.

Trademarks

NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice. © NETGEAR, Inc. All rights reserved.

Compliance

For the current EU Declaration of Conformity, please visit: http://support.netgear.com/app/answers/detail/a_id/11621/.

For indoor use only. Sale is authorized in the European Union, European Free Trade Association countries, and Switzerland.

NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134, USA

Document Version: 201-17335-01
Date: May 2013