RYTMISK Range Hood Installation Guide

Safety Information

Warning! Before proceeding with installation, read the safety information in the User Manual.

Fixing devices for the wall are not included since different wall materials require different types of fixing devices. Use fixing devices suitable for the walls in your home and for the weight of the appliance. For advice on suitable fixing systems, contact your local specialized dealer.

Warning: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards ⚠️.

Tools and Materials Required

Tools required for installation are shown: a tape measure, a screwdriver, a spirit level, a pencil, protective gloves ?, and a drill ?️. Safety icons indicate important actions: a person with crossed arms ❌ signifies prohibition, a person with a hammer ✔️ signifies a required action, and a person with a question mark ❓ suggests consulting the manual.

Parts Included

• A: Screws (4x)
• B: Mounting plate (1x)
• C: Duct adapter (1x)
• D: Hose clamp (1x)
• E: Cover/Shield (1x)
• F: Wall brackets (2x)
• G: Power cord with plug (1x) ?
• H.1: Manual/Instructions (1x)

Recommended Accessories (Purchase Separately)

Recommended accessories available for purchase are displayed, indicated by a shopping cart icon ?:

• Wall mounting hardware: Screws (Ø 5mm, 4x; Ø 6mm, 3x) and wall plugs (7x)
• Exhaust duct hose (Ø 120/125/150 mm, 1x)
• Replacement filter (NYTTIG FIL 400, 1x)

Dimensions and Installation Heights

Diagrams illustrate the RYTMISK range hood with key dimensions. The hood requires specific minimum and maximum installation heights above the cooking surface:

• For electric/ceramic cooktops: Minimum 500 mm clearance.
• For gas cooktops: Minimum 650 mm clearance.
• Overall minimum installation height: 715 mm (or 630 mm for gas cooktops).
• Maximum installation height: 995 mm.

Overall dimensions of the hood body are approximately 598 mm in width and 471 mm in depth.

Installation Steps

1. Step 1: Mark the Wall

   Using a spirit level, draw a precise vertical reference line on the wall.

2. Step 2: Mark Horizontal Line

   Draw a horizontal reference line at the desired height for the mounting bracket, ensuring it is level.

3. Step 3: Position Template and Mark Holes

   Align the mounting plate template (H.1) with the reference lines on the wall and mark the screw hole locations.

4. Step 4: Drill Holes

   Drill holes at the marked positions. A close-up view shows a Ø 6mm drill bit being used.

5. Step 5: Discard Packaging

   Dispose of all packaging materials properly ?️.

6. Step 6: Attach Wall Brackets

   Attach the two wall brackets (F) to the mounting plate. The diagram indicates the required vertical clearance range (min 630mm/715mm to max 995mm) and a small gap (≥1-2 mm) between brackets.

7. Step 7: Prepare Wall for Fixings

   Drill holes for wall plugs. The diagram shows drilling with Ø 5mm (4x) and Ø 6mm (3x) drill bits. Insert the corresponding wall plugs (7x) into the holes.

8. Step 8: Secure Wall Brackets

   Insert and tighten screws (Ø 6mm, 2x) into the wall brackets (F).

9. Step 9: Mount Hood Body

   Carefully lift and position the main hood body, engaging it with the wall brackets (F).

10. Step 10: Attach Side Covers

    Attach the side decorative panels or covers to the main hood body.

11. Step 11: Insert Grease Filter

    Insert the grease filter (NYTTIG FIL 400) into its designated position within the hood.

12. Step 12: Install Fan Unit

    Install the internal fan unit into the hood body. Secure the fan unit using two screws (2x).

13. Step 13: Secure Hood from Underneath

    From underneath, secure the main hood body to the wall brackets using one screw (1x, Ø 6mm).

14. Step 14: Attach Hood to Brackets

    Attach the hood body to the wall brackets (F) by inserting and tightening the provided screws (one screw per bracket connection is implied).

15. Step 15: Attach Main Mounting Plate

    Attach the main mounting plate (F) to the ceiling or wall structure using four screws (4x, Ø 5mm). Warning icons ⚠️ indicate correct and incorrect methods of attaching the bracket.

16. Step 16: Choose Installation Type

    The diagram illustrates two installation options: ducted exhaust (left) and recirculation (right). Airflow arrows show air being expelled outwards for ducted installation.

17. Step 17: Attach Top Cover

    Attach the top cover or shield (E) to the top of the hood.

18. Step 18: Connect Duct Adapter

    Connect the duct adapter (C) to the hood's exhaust outlet. Note: The adapter is designed for Ø 120/125 mm ducts; a Ø 150 mm duct is incompatible ❌.

19. Step 19: Connect Exhaust Duct

    Connect the flexible exhaust duct to the adapter (C) and secure it tightly with the hose clamp (D). The diagram shows how to attach and tighten the clamp.

20. Step 20: Connect to Mounting System

    Connect the hood assembly to the wall/ceiling mounting system. A warning symbol ⚠️ highlights the electrical connection point.

21. Step 21: Secure Assembly

    Secure the exhaust duct and the fan unit assembly to the wall or ceiling structure.

22. Step 22: Secure Fan Unit

    Install the fan unit within the hood body, securing it with four screws (4x, A).

23. Step 23: Adjust Chimney

    Adjust the telescopic chimney sections to the correct height. The diagram shows how to slide and lock the sections into place.

24. Step 24: Attach Bottom Cover

    Attach the bottom decorative panel or cover to the underside of the hood, clipping it into place.

25. Step 25: Control Panel Operation

    The diagram shows the control panel with speed settings ranging from 0 (off) to 8. A cross symbol ❌ indicates an invalid or off state.

26. Step 26: Attach Cover (B)

    Attach cover (B) as shown.

27. Step 27: Electrical Connection Details

    Details the routing and connection of the power cord. Warning icons ⚠️ indicate correct and incorrect wiring procedures.

28. Step 28: Final Assembly Check

    This step shows final checks and connections, including securing the fan unit with screws (4x, A).

29. Step 29: Filter and Fan Check

    This step involves installing the filter (NYTTIG FIL 400) and checking the fan rotation.

30. Step 30: Final Cover Attachment

    Final attachment of the bottom cover and control panel operation details.