HOW TO ASSEMBLE

AFTER SALES SERVICE

CUSTOMER SUPPORT

WE ARE HERE TO HELP

For general questions: bit.ly/3kY07dP

ASSEMBLY INSTRUCTIONS

BEFORE ASSEMBLY

1. Please CAREFULLY READ all instructions BEFORE STARTING THE ASSEMBLY of the Automatic Side Louver Opener.
2. Carry out the steps in the order set out in the instructions.
3. Close the louvre. Press upwards to ensure louvre blades are fully closed. If necessary, adjust the position of the louvre opener to ensure that the louvre blades are fully closed.
4. Tighten the two screws just enough to hold the louver control opener firmly in place and to ensure it does not slip. Do not overtighten.
5. It is necessary to cool the cylinder before fitting.
6. Fit the adjusting screw into the end of the cylinder.

FITTING THE UNIT

• If a manual vent opener is already assembled, it should be removed.
• Follow the next steps for fitting the unit according to the greenhouse model you have purchased.
• After allowing the cylinder to reach the temperature at which you wish the louver to start opening, operate the louver manually by pulling down on the arm to remove the pressure and firmly turn the adjusting screw in the direction of the 'LO' arrow (clockwise), until the unit begins to open the louver without manual assistance.
• Any rise of the greenhouse temperature will now cause the louver to open wider. Further adjustment may be necessary, in which case repeat the process.
• By turning the adjusting screw in the direction of the 'LO' arrow (clockwise) the louvre starts opening at a lower temperature. If the adjusting screw is turned in the direction of the 'HI' arrow (anti-clockwise) the louver will not open until a higher temperature is reached.
• Please note adjustment cannot be made without operating the unit manually by pulling down on the arm to relieve the return spring pressure.
• Manual Override - If you wish to open or close the louver manually, remove the top half of the plastic catch and carefully remove the link arm from the pivot pin. Providing you do not move the unit or the adjusting knob, the unit will operate at your chosen temperature when reconnected.

IMPORTANT INFORMATION

• Do not heat more than 50°C (122°F).
• Do not apply heavy load on louver when locking or covering.
• Do not attempt to dismantle the cylinder.

TECHNICAL INFORMATION

Opening temperature range adjustable between 15°C and 25°C (59°F and 77°F) GUARANTEED

TOOLS & EQUIPMENT

• Wrench 10 mm | 3/8"
• Wrench 7 mm | 1/4"
• Philips Head Screwdriver
• Flat Head Screwdriver
• Cordless Drill with 4 mm | 5/32" Drill Bit

DURING ASSEMBLY

During assembly, you will encounter different icons for different products. Please see below for more information:

• Icon indicating installer should be inside the product: ?
• Icon indicating installer should be outside the product: ⬆️

DETAILED ASSEMBLY STEPS

Section 1: Suitable for HARMONY / HYBRID / MYTHOS / GLORY / OCTAVE / BALANCE / ESSENCE / AMERICANA

1. Step 1: Shows a cylinder being placed in a cooling container (e.g., ice bath) for approximately 30 minutes.
2. Step 2: Illustrates attaching a bracket to the louver window frame using screws (parts 423, 421, 428). The bracket is positioned on the frame.
3. Step 3: Depicts mounting the main opener mechanism onto the previously attached bracket. This step includes an icon indicating the installer should be inside the greenhouse (?). Screws are used for attachment.
4. Step 4: Shows securing the main opener mechanism firmly to the bracket with screws (part 428).
5. Step 5: Illustrates attaching a bracket to the louver blade itself, using screws.
6. Step 6: Shows connecting the arm of the opener mechanism to the bracket that is attached to the louver blade.
7. Step 7: Depicts securing the connection between the opener arm and the louver bracket with a screw.
8. Step 8: Shows attaching the cylinder unit to the main opener mechanism using screws (parts 423, 421).
9. Step 9: Illustrates closing the louver blades completely by pushing them upwards. An arrow indicates the direction of movement. A checkmark symbol (✔️) confirms the blades are fully closed.
10. Step 10: Shows fitting the adjusting screw into the end of the cylinder.
11. Step 11: Demonstrates the manual override and temperature adjustment. The arm is pulled down to release pressure, and the adjusting screw is turned. Icons indicate temperature settings (❄️ for cold, ? for night/lower temperature).

Section 3: Suitable for GRAND GARDENER / PRESTIGE / HOBBY GARDENER / ECO GROW

1. Step 1: Similar to Section 1, Step 1: Cylinder cooling for 30 minutes.
2. Step 2: Attaching a bracket to the louver window frame with screws (parts 423, 428) and a specific part (8766).
3. Step 3: Mounting the main opener mechanism to the bracket. Includes the installer inside icon (?) and a 4mm drill bit symbol.
4. Step 4: Securing the opener mechanism with screws (parts 423, 428) and part 8766.
5. Step 5: Attaching a bracket to the louver blade with screws.
6. Step 6: Connecting the opener arm to the louver blade bracket.
7. Step 7: Shows securing the connection with screws. Includes a 'X' symbol (likely indicating incorrect method) and a warning symbol (!).
8. Step 8: Attaching the cylinder unit to the main opener mechanism with screws.
9. Step 9: Shows drilling a 4mm hole and attaching parts (428, 423) to the louver frame.
10. Step 10: Attaching the opener mechanism to the louver frame with screws.
11. Step 11: Shows connecting the cylinder to the opener mechanism.
12. Step 12: Depicts the manual override: pulling the arm down and then connecting the cylinder.
13. Step 13: Shows final attachment of components.
14. Step 14: Illustrates temperature adjustment with cold (❄️) and night (?) icons.

Section 6: Suitable for OASIS SERIES

1. Step 1: Similar to Section 1, Step 1: Cylinder cooling for 30 minutes.
2. Step 2: Attaching a bracket to the louver window frame with screws (parts 423, 421, 428).
3. Step 3: Mounting the main opener mechanism to the bracket. Includes the installer inside icon (?).
4. Step 4: Shows drilling a 4mm hole and attaching parts to the louver frame.
5. Step 5: Attaching a bracket to the louver blade with screws.
6. Step 6: Connecting the opener arm to the louver blade bracket.
7. Step 7: Depicts closing the louver blades and confirming they are fully closed (✔️).
8. Step 8: Shows drilling a 4mm hole and attaching the opener mechanism to the frame.
9. Step 9: Shows attaching the cylinder unit to the main opener mechanism using screws (parts 428, 423).
10. Step 10: Shows connecting the opener arm to the louver blade bracket and securing with screws.
11. Step 11: Depicts the manual override: pulling the arm down and connecting the cylinder.
12. Step 12: Illustrates temperature adjustment with cold (❄️) and night (?) icons.