DC Power Ceiling Fan Remote Control Manual

Learning Process

NOTE: The Hand Held Remote Control System is equipped with a learning frequency function which has code combinations to prevent potential interference from other remote units.

1. Open the remote battery cover and install DC3V, AAA 2pcs batteries.
2. Within 30 seconds of turning the Receiver's AC power ON.
3. Press and hold the remote [LEARN key] for over 5 seconds. Once the receiver has detected the frequency, the receiver will make a [Bi Bi sound] twice. This will indicate the receiver has learned the frequency that was previously selected on the transmitter.

NOTE: After the AC power is on, do not press any other button on the transmitter before setting learning. Doing so will cause the procedure to fail. After completing the steps above, you should be able to operate the ceiling fan and light. If the fan is not responding to the transmitter, please turn the power off to the receiver and repeat steps 1 and 2.

NOTE: Remove the battery if not used for long periods of time to prevent damage to the hand held remote.

The remote control features a battery compartment, a LEARN button, and indicator lights.

Light Function Select Switch

If an energy-saving light is installed onto the ceiling fan, please slide the "light function select switch" to the "O" position. If a tungsten light is installed onto the ceiling fan, please slide the "light function select switch" to the "D" position.

Functions of Transmitter

1. To turn the fan on or off.
2. [increase speed]: Press this button to increase fan speed. The LED indicator will show the current fan speed position (1-6 speed).
3. [decrease speed]: Press this button to decrease fan speed. The LED indicator will show the current fan speed position (1-6 speed).
4. FAN TIMER:
   • [2-hour timer]: Sets the ceiling fan to turn off automatically after 2 hours.
   • [4-hour timer]: Sets the ceiling fan to turn off automatically after 4 hours.
   • [8-hour timer]: Sets the ceiling fan to turn off automatically after 8 hours.
   Press a fan speed button to deactivate the timer.
5. [fan direction toggle]: To set fan wind direction up or down.
6. [Walk Away Delay]: Tap once to activate. The light on the ceiling fan blinks once to confirm Walk Away Delay is active. The light turns off after 1 minute. Press any key to cancel this function.
7. [Home Shield]: Press and hold the button to activate. The light on the ceiling fan blinks twice to confirm Home Shield is active. The fan remains off, and the light randomly turns on for a minimum of 5 minutes and a maximum of 20 minutes. The light remains off for 60 minutes between events.
8. [Natural Flow]: Press this button for automatic fan speed changes. Press a Fan Speed button to deactivate.
9. [light toggle]: To turn the light on and off.
10. [light dimming]: Press and hold to dim or brighten the light to the desired level and release.
11. [CCT toggle]: Press and hold to change the CCT (Correlated Color Temperature).

When pressing a remote button, the LED indicator on position 1 will be on. If you press a remote button and the LED indicator does not turn on, you should change the batteries to new DC3V, AAA 2pcs batteries.

FCC Compliance Information

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

To assure continued FCC compliance: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.

Model: TRD050G2Z

FCC ID: 2AQZU-18066

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.