ASA Electronics MSBAR Marine Waterproof Bluetooth/Aux Soundbar

Important Information

Weight Warning

The MSBAR weighs 14lbs (6.35 Kg). Before mounting, ensure the intended mounting surface can properly support this weight.

FCC Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to two conditions: (1) it may not cause harmful interference, and (2) it must accept any interference received. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, designed to provide reasonable protection against harmful interference in a residential installation. It may cause interference if not installed and used correctly. If interference occurs, users are encouraged to try correcting it by reorienting/relocating the antenna, increasing separation between equipment and receiver, connecting to a different circuit, or consulting a dealer/technician. This equipment complies with FCC radiation exposure limits for an uncontrolled environment and should be installed/operated with a minimum distance of 20cm between the radiator and the body.

California Proposition 65 Warning

⚠️ WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Features

Marine Waterproof Bluetooth/Aux Soundbar with Integrated LED Light Strip

Bluetooth

• Version: 5.0
• Range: 33ft (10m) Class 2

Speakers

• Cone Type: polypropylene

Amplifier

• Rated Power (RMS): 120W
• Rated Power (Peak): 180W
• Frequency Response: 75Hz~13KHz

General

• Operational Power: 12VDC (Max Current Draw: 12A, Fuse: 15A)
• Cabinet Material: Aluminum Extrusion
• Color: Black Powder Coating
• Weight: 14lbs / 6.35kg
• Dimensions: 780x202x137.5(mm) / 30.7”x7.95"x5.41"(inch)

Diagram Description: A diagram shows the overall dimensions of the soundbar with measurements for length (780mm/30.7"), height (202mm/7.95"), and depth (137.5mm/5.41").

Contents

• MSBAR Soundbar Speaker System - 1
• N-Bracket - 2
• N-Rubber Bushing: 85mm(3.35")x23mm(0.9")x1.5mm(0.059") - 2
• Rubber Bushing: 45mm(1.77")x35mm(1.38")x1.5mm(0.059") - 2
• M8 Bolt - 2
• M8 Lock Nut - 2
• Quick Reference Guide - 1
• Zip tie + double stick tie mount - 1

Safety Information

General Precautions

• Read the entire instruction manual for full satisfaction and keep for future reference.
• Follow all operation guidelines and safety warnings.
• Do not install near heat sources (radiators, heat registers, stoves, amplifiers).
• Only use manufacturer-specified attachments/accessories.
• Never use harsh cleaning agents; clean with mild cleaner and soft cloth.

When Driving

Keep volume low enough to be aware of your surroundings.

Protect from Water

Do not submerge. Avoid power washing as water pressure may exceed IPX5 rating.

Protect from High Temperatures

Avoid prolonged exposure to direct sunlight. Allow interior to cool before playback. Do not mount near the engine compartment.

Use the Proper Power Supply

Designed for a 12 volt DC negative ground battery system.

WARNINGS

• DO NOT OPEN, DISASSEMBLE OR ALTER THE UNIT.
• USE THE CORRECT AMPERE RATING WHEN REPLACING FUSE.
• DO NOT INSTALL IN LOCATIONS THAT MIGHT HINDER VEHICLE OPERATION.
• INSTALL WIRING TO AVOID CRIMPING OR PINCHING BY SCREWS OR SHARP METAL EDGES. Use rubber grommets for holes and sealing caulk for openings to prevent water entry.
• Choose a flat mounting location with clearance for ventilation. Orient and mount horizontally or vertically if possible.
• Before drilling, inspect the area for existing wires, fuel lines, or tanks.
• Always disconnect the vehicle negative battery terminal during installation.

Mounting the Soundbar

With N-Bracket

Diagram Description: Illustrates mounting the soundbar using an N-bracket. Components shown include N-Bracket, M8 Bolt, Rubber Bushing, N-Rubber Bushing, and M8 Lock Nut. The process involves installing rubber bushings on the square bar, then N-brackets on the rubber bushings, followed by installing rubber bushings on the side-brackets. Finally, align bolts and nuts and tighten firmly.

Dimensions for N-Rubber Bushing: 46MM(1.81"), 2*Ø7.5MM(0.295"), 25.2MM(0.992"). Dimensions for Rubber Bushing: R2.5mm(0.098"), 1.5mm(0.059"), 28.3mm(1.114"), 34MM(1.339"), 24mm(0.95").

Without N-Bracket

Diagram Description: Illustrates mounting the soundbar directly to the mounting surface. Components shown include Side-Bracket, Rubber Bushing, M6 Screwing, M6 Lock Nut, and M6 Bolt. This method involves screwing or bolting directly into the mounting surface.

Overall dimensions for mounting surface are indicated: 6.5mm(4"), 857.5mm(33.76"), 6.5mm(4"), 25mm(0.985"), 25mm(0.985").

Side-Bracket Adjustment

Diagram Description: Shows how the side-bracket can be adjusted for left/right angles and height. Loosen the screw to adjust, then re-tighten. When the bracket is vertical, use the center hole and one side hole. In other cases, use the two available holes on the bracket slot. Components shown: Side-Bracket, Rotation, M6 Washer, M6 Bolt, Movement. Note: A bolt is always required in the center.

Wire Diagram

Amphenol ATP04-4P Connector

• 1 - Ground (-)
• 2 - Power (+12V)
• 3 - Remote
• 4 - Filled with a sealing plug

3.5mm AUX Connections

• AUX OUT: Connects to the AUX input of a second MSBAR, subwoofer amplifier, or other audio system expansion. Signal level is 2 Volts.
• AUX IN: For audio input.

Diagram Description: A diagram shows the Amphenol ATP04-4P connector with pins labeled 1-4. It also shows 3.5mm AUX OUT and 3.5mm AUX IN connectors. The soundbar unit is depicted below these connectors.

Note: The 'REMOTE' wire can connect to a +12VDC switched source or amplifier remote turn-on from the head unit. Connecting to the head unit's remote turn-on is recommended to prevent popping noise.

Operation

Power/Bluetooth

• Press the Power/Bluetooth switch to turn the device on/off (standby).
• Press and hold the Power/Bluetooth Switch for ~3 seconds to enter Bluetooth pairing mode (device name: MSBAR). Pairing mode lasts 120 seconds. If no device is paired, it returns to normal operation. The last paired device is remembered.
• Bluetooth pairing is only needed for new devices. When power is on, MSBAR automatically connects to the last paired device.
• LED Status: The LED ring is always on when Bluetooth is connected or in AUX mode. It is off when the power is off (standby). It flashes slowly when in Bluetooth mode and no device is connected.
• Mode Switching: When a 3.5mm AUX input is detected, the unit automatically switches to AUX mode. If no AUX input is detected, it switches back to Bluetooth mode. This switching is controlled by AUX input detection only.

LED Light Bar Switch

• Press the LED light bar switch to turn the LED light bar on/off.
• When the MSBAR is powered, the LED on/off switch has a blue light ring for easy location at night.

Diagram Description: Shows the front of the soundbar with two switches labeled: "Switch - Power&Bluetooth Pairing (Blue LED ring color)" and "Switch - Led light bar on/off (Blue LED ring color)".

Manufacturer Information

ASA ELECTRONICS, LLC

2602 MARINA DRIVE ELKHART IN 46514

U.S.A.

MADE IN CHINA