Husqvarna Automower® 310/315/315X Quick Guide

1. Installation and Connecting the Charging Station

1. Placement

   Place the charging station in a central position within the working area, ensuring ample open space in front and a relatively horizontal surface.

2. Power Connection

   Connect the power supply's low-voltage cable to the charging station and the power supply unit. Then, connect the power supply to a 100-240V wall socket.

3. Initial Charging

   Place the robotic lawn mower in the charging station to charge the battery while you lay the boundary wire. Set the main switch to position 1.

2. Placement of Boundary Wire and Guide Wire

1. Boundary Wire

   Lay the boundary wire to form a loop around the entire working area.

2. Guide Wire Connection Point

   Create an eyelet (a small loop) in the boundary wire at the point where the guide wire will be connected later.

3. Guide Wire Routing

   Run the guide wire from its starting point to the boundary loop eyelet. Avoid sharp angles when laying the wire.

3. Connecting the Boundary Wire and Guide Wire

Narrow passages in the yard can make it difficult for the robotic lawn mower to find the charging station. The guide wire assists the mower in quickly locating the station and can also lead it to remote areas.

1. Guide Wire Placement Relative to Station

   Lay the guide wire under the charging station and extend it at least 2 meters (7 ft) straight out from the front edge of the charging station.

2. Connector Preparation

   Open the wire connectors and insert the ends of the boundary and guide wires into the designated recesses within each connector.

3. Securing Connectors

   Press the connectors together firmly using a pair of pliers.

4. Trimming Excess Wire

   Cut off any surplus boundary wire, leaving approximately 1-2 cm (0.4-0.8") above the connectors.

5. Connecting to Charging Station

   Press the connectors onto the contact pins marked AL (left) and AR (right) on the charging station. Ensure the right-hand wire connects to the right pin and the left-hand wire to the left pin.

6. Final Connection

   Fasten the connector to the contact pin marked G1 on the charging station.

4. Connecting the Guide Wire to the Boundary Wire

1. Cutting Boundary Wire

   Cut the boundary wire in the center of the eyelet created in step 2.2 using wire cutters.

2. Joining Wires

   Connect the guide wire to the boundary wire using the provided couplers. Press the couplers completely together using pliers.

5. Starting and Stopping

1. Starting the Mower

   Open the cover by pressing the [STOP button]. Set the main switch to position 1. For the first-time setup, a sequence will begin, including selecting a four-digit PIN. Then, press the [START button] and close the cover.

2. Stopping the Mower

   Press the [STOP button].

6. Adjusting for Lawn Size

Mowing results are influenced by mowing time. Adjust the mowing schedule via the app to suit your lawn's needs. The mower's capacity is approximately:

• Automower® 310: 56 m²/hour (603 ft²/hour)
• Automower® 315: 68 m²/hour (732 ft²/hour)
• Automower® 315X: 73 m²/hour (786 ft²/hour)

For example, for an 800 m² (8600 ft²) lawn:

• Automower® 310: requires 15 hours/day
• Automower® 315: requires 12 hours/day
• Automower® 315X: requires 11 hours/day

7. Maintenance

1. Ensure the main switch is in position 0 for all chassis work, such as cleaning or blade replacement. Replace blades regularly for optimal mowing results.

2. Never clean the robotic lawn mower with a high-pressure washer, running water, or solvents.

3. If there is a risk of a thunderstorm, disconnect all connections to the charging station (power supply, boundary wire, and guide wire).

4. Fully charge the battery at the end of the season before storing the mower for winter.

8. Indicator Lights

The charging station and mower may display indicator lights to show status:

• Green solid light: Good boundary loop signal.
• Green flashing light: ECO mode is activated.
• Blue flashing light: Malfunction in the boundary loop.
• Red flashing light: Malfunction in the charging station's antenna.
• Red solid light: Fault in the circuit board or incorrect power supply. This requires attention from an authorized service technician.

9. Automower® Connect App

Enhance your mower's functionality with the Automower® Connect app.

1. Download and Setup

   Download the Automower® Connect app from the App Store or Google Play. Sign up with your email and password to create a Husqvarna account. Log in to your account within the app.

2. Adding Your Mower

   In the app, select "My mowers," then tap the plus sign (+). Follow the on-screen instructions to add your mower.

3. Connectivity Options

   The app offers:

   • Long-range cellular connectivity (Automower® Connect).
   • Short-range Bluetooth® connectivity (Automower® Connect@Home).
   • Device tracking (GPS) (available with Automower® Connect).