Garmin ECHOMAP Ultra 2 16xsv Installation Instructions

Important Safety Information

Please refer to the Important Safety and Product Information guide included in the product packaging for product warnings and other important information.

Warning:

Do not remove the inline fuse holder when connecting the power cable. Always use the correct fuse as indicated in the product specifications to prevent the risk of fire or product damage due to overheating. Failure to use the correct fuse when connecting the power cable will void the product warranty.
Failure to install this device according to these instructions may result in personal injury, damage to the boat or equipment, or reduced product performance.

Caution:

To prevent possible personal injury, always wear safety glasses, ear protection, and a dust mask when drilling, cutting, or grinding.
To prevent possible personal injury or damage to the equipment and boat, disconnect the boat's power before installing the equipment.
To prevent possible personal injury or damage to the equipment and boat, ensure the equipment is properly grounded before connecting power to the equipment.
To prevent possible personal injury or damage to the equipment and boat, install this equipment only when the boat is out of the water, or when the boat is properly secured and docked in calm water conditions.

Note:

When drilling or cutting, always check the surface on the opposite side to avoid damaging the boat.
Read all installation instructions before proceeding with the installation. If you encounter difficulties during installation, contact Garmin Product Support.

Required Tools

Drill bit
Drill bit
For bracket installation: Use a 3 mm (1/8 in.) drill bit and select screws that match the mounting surface and hardware.
For flush mounting: Use 3.2 mm (1/8 in.) and 8.5 mm (11/32 in.) drill bits.
#2 Phillips screwdriver
Jigsaw or rotary tool
File and sandpaper
Marine sealant (optional)

Interface Diagram

Label	Description
POWER	Power
12 PIN XDCR	12-pin Transducer
HDMI	HDMI Video Output
Ground Screw	Ground Screw
NETWORK	Garmin Network port, for connecting compatible LiveScope™, GCV™ and ECHOMAP units. Note: This unit is not compatible with some Garmin marine network devices, such as GPSMAP, GSD™ and radar units.
NMEA 2000	NMEA 2000 Network

Software Update

After installation, you may need to update the chartplotter software. For instructions on how to update the software, refer to the owner's manual: garmin.com/manuals/echomap_ultra_2_16xsv.

Installation Considerations

You can flush-mount the unit or mount it on the dashboard using the bracket.

When choosing a mounting location, follow these considerations:

The mounting location must provide a clear view of the screen and easy access to the unit's buttons.
The mounting location must be strong enough to support the unit and bracket.
Cables must be long enough to connect the components and to the power source.
To avoid interference with a magnetic compass, the unit must be installed at a distance that is greater than the specified compass safe distance.

Installing with the Bracket

You can mount the unit on a flat surface using the bracket.

Use the bracket-mount bracket ① as a template to mark the mounting hole locations ②.
Drill the pilot holes using a 3 mm (1/8 in.) drill bit.
Attach the mounting bracket to the surface using the included washers and wood screws ③.
Install the bracket-mount knobs ④ on the sides of the unit.
Place the unit into the bracket-mount bracket and tighten the bracket-mount knobs.
Install the hole plugs into the edges of the unit to secure them.

	Garmin ECHOMAP Ultra 2 16xsv Installation Instructions Comprehensive installation guide for the Garmin ECHOMAP Ultra 2 16xsv marine electronics device, covering safety precautions, mounting options, and connectivity.
	Garmin ECHOMAP Ultra 2 16xsv Installation Instructions This document provides detailed installation instructions for the Garmin ECHOMAP Ultra 2 16xsv marine electronics device, covering safety information, required tools, mounting procedures, and connectivity options.
	Garmin ECHOMAP Ultra Installation Guide Comprehensive installation guide for the Garmin ECHOMAP Ultra marine chartplotter/fishfinder, covering bracket and flush mounting, wiring, transducer connection, and NMEA 2000 networking.
	Garmin ECHOMAP Ultra 2 16xsv Installation Guide This document provides installation instructions for the Garmin ECHOMAP Ultra 2 16xsv chartplotter, covering safety information, connector details, mounting considerations, and connectivity options.
	Garmin ECHOMAP UHD Installation Guide Comprehensive installation instructions for the Garmin ECHOMAP UHD series marine electronics, covering bail mount, swivel mount, and flush mount installations, wiring, NMEA 2000/0183 connectivity, and specifications.
	Garmin ECHOMAP UHD2 6/7/9 SV Installation Instructions This document provides comprehensive installation instructions for the Garmin ECHOMAP UHD2 6, 7, and 9 SV series marine chartplotters. It covers essential safety information, tools required, various mounting methods (bail mount, swivel mount, flush mount), connection considerations for power, transducers, and NMEA 2000 networks, as well as device installation and removal procedures and detailed product specifications.
	Garmin ECHOMAP Ultra 2 16xsv Installation Guide This document provides installation instructions for the Garmin ECHOMAP Ultra 2 16xsv, including safety information, required tools, mounting procedures for flush and surface mounting, and connection details for transducers, NMEA 2000, and HDMI.
	Garmin ECHOMAP UHD2 5X/7X: Marine Chartplotter and Fishfinder Owner's Manual This owner's manual provides comprehensive instructions for the Garmin ECHOMAP UHD2 5X/7X marine chartplotter and fishfinder. Learn about navigation, sonar features, customization, ActiveCaptain app integration, and troubleshooting for your boating needs.