ETA Vital Blend Mini II Blender

Safety Warnings

• Read all instructions carefully before operating the appliance.
• Check that the voltage on the type label matches your socket. Connect the plug only to a properly earthed socket conforming to standards.
• Never use the appliance if the power cord or plug are damaged, if it is not functioning correctly, or if it has fallen and been damaged or into water. Take it to a professional service centre.
• This appliance must not be used by children. Keep the device and cord out of reach of children. Persons with reduced physical or mental abilities or lack of experience may use it under supervision or if instructed on safe use and potential dangers. Children must not play with the appliance.
• If the power cord is damaged, it must be replaced by the manufacturer, their service technician, or a similarly qualified person to prevent a dangerous situation.
• Always unplug the appliance from the power supply if you leave it unattended.
• Before replacing accessories, moving parts, assembly, disassembly, cleaning, or maintenance, turn off the appliance and disconnect it from the mains by pulling the power cord.
• Be careful when handling the blender; the knife is very sharp!
• CAUTION: Do not use with a program, time switch, or any other part that turns the appliance on automatically, as there is a risk of fire if the appliance is not covered or placed properly.
• When the appliance is in operation, prevent pets, plants, or insects from contacting it.
• Ensure the container is properly attached and the lid is secured before switching on the propulsion unit.
• Never remove or attach the container while the propulsion unit is in operation to avoid risk of injury or damage.
• After finishing work and before cleaning, always switch off and disconnect the appliance from the power supply.
• The product is intended for home use and similar environments (shops, offices, hotels, motels, B&Bs). It is not intended for commercial use.
• Do not use in damp or wet environments or in any environment with the danger of fire or explosion (e.g., where chemicals, fuels, oils, gases, paints, or other flammable/volatile materials are stored).
• Maximum processing time is 6 minutes, followed by a break of approximately 10 minutes for the motor unit to cool down.
• Correctly placing the bowl on the appliance releases the safety lock, allowing it to be turned on.
• When mixing liquids, never add more than 1850 ml and always use the lid. Maximum hot food volume is 1000 ml.
• The appliance is equipped with a thermal safety fuse that disconnects power in case of motor overload. If this occurs, unplug the appliance and let it cool for at least 10 minutes.
• Never immerse the drive unit in water or wash it under running water.
• Do not switch on the appliance without ingredients.
• Do not put more liquid than marked on the container and always use the lid when mixing or blending liquids.
• Do not process ingredients above approximately 60°C.
• Use the mixer only in its working position, on stable surfaces away from heat sources (stoves, cookers, grills) and wet surfaces (sinks).
• If ingredients stick to the accessories (knife, container walls, lid), switch off the appliance and carefully clean with a spatula.
• Use only with accessories intended and supplied for this type of device. Using other accessories may pose a danger.
• Never insert fingers, forks, knives, spatulas, or spoons into rotating parts.
• Regularly check the condition of the power cord.
• Prevent the supply cord from hanging loosely over the edge of the work desk where children could reach it.
• The power cord must not be damaged by sharp or hot objects, open fire, or bent over sharp edges.
• If an extension cord is needed, ensure it is undamaged and meets applicable standards.
• Never use the appliance for any purpose other than that for which it is intended and described in this manual.
• [Warning Symbol] Warning: Incorrect use of the appliance, not in accordance with the manual, carries a risk of injury.
• The manufacturer is not responsible for damage and injuries caused by improper use or accessories (e.g., food spoilage, cuts from the knife, fire) if safety warnings are not followed.
• Warning: If the blender runs idle (e.g., blade cannot touch ingredients), disconnect from mains and release ingredients. The blender cannot run idle for more than 10 seconds.

Appliance Description

The blender consists of the following parts:

A – Propulsion Unit

• A1 – Propulsion shaft
• A2 – Rubber feeder
• A3 – Supply cord

B – Control Panel

• B1 – "SMOOTHIE" program button
• B2 – "ICE" program button
• B3 – "QUICK CLEAN" program button
• B4 – "PULSE" button
• B5 – Rotary speed controller

C – Dish (Container)

• C1 – Handle
• C2 – Knife (blade assembly)

D – Lid

• D1 – Cap with measuring cup (40 ml)
• D2 – Lid seal
• D3 – Hinged spout cap
• D4 – Spout seal

Preparation for Use

Remove all packaging material and accessories. Remove any adhesive foils, stickers, or paper from the appliance. Before first use, wash parts that come into contact with food in hot, soapy water, rinse thoroughly with clean water, and wipe dry or let them dry. A short, mild smoke or odor during the first use is not a defect and not a reason for complaint.

Appliance Assembling (Fig. 1)

Assemble the appliance according to Fig. 1. Correctly placing container C onto the drive unit will release the safety lock, and the appliance can then be used. Dismantle by reversing the procedure.

Control

1. Switching to Standby Mode: Connect drive unit A to the mains. Place container C on the drive unit. Once the container is fitted and secured, the blender automatically switches to standby mode. All buttons (B1-B4) will flash. Individual functions can then be set.
2. Manual Speed and Time Setting: Use the rotary control B5 to set the desired speed (MIN-MAX). After finishing work, turn control B5 to the OFF position.
3. Using Pre-set Programmes: Press button B1/B2/B3 to select the desired program (SMOOTHIE, ICE, QUICK CLEAN). The program will start (the indicator light of the corresponding button will illuminate). Wait for the program to finish. The program can be terminated at any time by pressing the corresponding button again.

Note: The selected program can be terminated at any time by pressing the corresponding button (B1/B2/B3) again.

4) Using PULSE Button (B4): Press and hold button B4 to start maximum speed. Releasing it stops the motor.

Using the Blender

Place the closed container with ingredients onto the drive unit. Then use manual speed and time settings or one of the pre-set programs (see Control). The blender is intended for preparing juices, milk cocktails, smoothies, sauces, soups, baby food, diet food, purées, etc.

Recommendations

• For proper ice cube crushing, observe the maximum quantity up to the 500 ml mark.
• Hot liquids (up to 60°C) can also be processed, e.g., sauces, soups.
• For liquids that foam (e.g., milk), never fill the container beyond the 1850 ml mark to prevent overflow. In this case, approximately 1000 ml is recommended.

Recommended Speeds for Processing Ingredients

This is a high-speed blender. Speeds range from 10000 to 16000 RPM. Always adjust speed considering the type, quantity, and ripeness of ingredients, especially for fruits and vegetables. It is recommended to start the blender at minimum speed and gradually increase power as needed. For frozen foods, always use maximum speed from the start.

Maintenance

Do not use rough or aggressive cleaning agents (e.g., sharp objects, scrapers, solvents). Clean the drive unit with a soft, damp cloth with detergent. Wash all accessories immediately after use in hot, soapy water, rinse with clean water, and dry. To clean the knife, pour about 0.5 L of clean water into the container, select the "QUICK_CLEAN" program, and turn on the appliance. If the knife is heavily soiled, repeat the procedure several times, or pour 1 L of water, add a small amount of detergent, and run the blender for 1 minute. Some ingredients may discolor accessories, but this does not affect function and usually disappears over time. Never dry plastic moldings over a heat source (e.g., stove, electric/gas cooker).

Replacing the Rubber Feeder A2

The rubber feeder is inserted into the drive shaft and is not secured. For removal, use a suitable tool to grip and pull it upwards (see Fig. 1), such as a thin screwdriver or narrow pliers.

Contact the manufacturer for spare parts and components.

More extensive maintenance or maintenance requiring intervention in the internal parts of the appliance must be carried out by a specialized service centre. Failure to comply with the manufacturer's instructions will void the right to repair.

Information regarding warranty and product repairs can be found on www.eta.cz/servis-eu.

Environmental Protection

If dimensions allow, all parts of the appliance, packaging, components, and accessories are marked with material symbols and recycling indicators. Symbols on the product or accompanying documentation indicate that electrical or electronic products must not be disposed of with municipal waste. For proper disposal, take them to designated collection points where they will be accepted free of charge. Proper disposal helps conserve valuable natural resources and prevent potential negative impacts on the environment and human health. For more details, contact your local authority or the nearest collection point. Improper disposal may be subject to fines according to national regulations. If the appliance is to be permanently taken out of service, it is recommended to cut the power cord to make the appliance unusable.

Technical Data

Input power when switched off is <0.50 W.

Sound power level is 85 dB(A) re 1pW.

The manufacturer reserves the right to change technical specifications and accessories according to the product model.

Illustrations are for guidance only.

Warnings and Symbols Used on the Appliance, Packaging, or in the Instructions Manual

• HOUSEHOLD USE ONLY. DO NOT IMMERSE IN WATER OR OTHER LIQUIDS.
• OPEN
• DO NOT BLEND HOT LIQUIDS
• CAUTION: DO NOT OPERATE WITHOUT THIS COVER IN PLACE
• TO REDUCE THE RISK OF INJURY, NEVER PLACE CUTTER-ASSEMBLY BLADES ON BASE WITHOUT JAR PROPERLY ATTACHED
• TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, ARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY. [Warning Symbol]