Installation Guide for FORTIN models including: 2022-2023, 2022-2023 Automatic Transmission Vehicles, Automatic Transmission Vehicles, Transmission Vehicles, Vehicles
EVO-ALL | Universal all-in-one data bypass and interface module. | Fortin Electronic Systems
File Info : application/pdf, 9 Pages, 3.29MB
DocumentDocumentALL Page 1 / 9 STAND ALONE INSTALLATION INSTALLATION STAND ALONE REV.: 20240521 Guide # 110661 ADDENDUM - SUGGESTED WIRING CONFIGURATION ADDENDA - SCHÉMA DE BRANCHEMENT SUGGÉRÉ ONLY COMPATIBLE WITH AUTOMATIC TRANSMISSION VEHICLES. COMPATIBLE AVEC VÉHICULE À TRANSMISSION AUTOMATIQUE SEULEMENT. Vehicle functions supported in this diagram (functional if equipped) | Fonctions du véhicule supportées dans ce diagramme (fonctionnelles si équipé) PUSH START Key Control Contrôle de clé Lock Unlock Disarm Parking Light Tailgate Release RAP Disable Tachometer Door Status Hand-Brake Status Foot-Brake Status OEM Remote Monitoring VEHICLE VEHICULES CHEVROLET Silverado 1500 GMC Sierra 1500 Push-To-Start Push-To-Start YEARS ANNÉES 2022-2023 2022-2023 · ··········· · ··········· MODEL: EVO-ALL DATE:02/2019 FORTIN.CA SN: 000000 00000 MADE IN CANADA © 2018 ALL RIGHTS RESERVED COMPATIBLE MODULE REQUIRED: 2019 MODULE COMPATIBLE REQUIS: QR CODE ON THE LABEL MANUFACTURED AFTER: 2019 CODE QR SUR L'ÉTIQUETTE FABRIQUÉ APRÈS: 2019 FIRMWARE VERSION VERSION LOGICIELLE 80.[03] MINIMUM To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately. Pour ajouter la version logicielle et les options, utilisez l'outil FLASH LINK UPDATER ou FLASH LINK MOBILE, vendu séparément. Program bypass option: Programmez l'option du contournement: UNIT OPTION OPTION UNITE C1 D6 DESCRIPTION OEM Remote status (Lock/Unlock) monitoring Suivi des status (Verrouillage/Déverrouillage) de la télécommande d'origine Push-to-Start Push-to-Start IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN: SI LE VÉHICULE N'EST PAS ÉQUIPÉ D'UN CONTACT DE CAPOT FONCTIONNEL: A11 OFF Hood trigger (Output Status). NON Contact de capot (état de sortie). Parts required (Not included) 1x Vehicle Key 1x ARE-1R0 1x 1 Amp. Diode 1x 1.5 K Ohm resistor 1x 7.5 Amp. Fuse Pièce(s) requise(s) (Non incluse(s)) 1x Clé du véhicule 1x ARE-1R0 1x Diode 1 Amp. 1x Résistance de 1.5 K Ohm 1x Fusible 7.5 Amp. NOTES 1 KEY REQUIRED FOR THE INSTALLATION 1 CLÉ REQUISE À L'INSTALLATION MANDATORY INSTALL | INSTALLATION OBLIGATOIRE * HOOD PIN CONTACT DE CAPOT HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, A11 OFF NON SET FUNCTION A11 TO OFF. STATUT DE CAPOT : LE CONTACT DE CAPOT, DOIT ÊTRE INSTALLÉ SI LE VÉHICULE PEUT DÉMARRER À DISTANCE, LORSQUE LE CAPOT EST OUVERT, PROGRAMMEZ LA FONCTION A11 À NON. Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed. THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE. Notice: l'installation des éléments de sécurité est obligatoire. Le contact de capot est un élément de sécurité essentiel et doit absolument être installé. CE MODULE DOIT ÊTRE INSTALLÉ PAR UN TECHNICIEN QUALIFIÉ, TOUTE ERREUR DANS LES BRANCHEMENTS PEUT OCCASIONNER DES DOMMAGES PERMANENTS AU VÉHICULE. This guide may change without notice. See www.fortin.ca for latest version. Ce guide peut faire l'objet de changement sans préavis. Voir www.fortin.ca pour la récente version. PARTS REQUIRED (NOT INCLUDED) | PIÈCES REQUISES (NON INCLUSES) 1x FLASH LINK UPDATER, 1x FLASH LINK MANAGER SOFTWARE | PROGRAMME 1x Microsoft Windows Computer with Internet connection Ordinateur Microsoft Windows avec connection Internet OR OU 1x FLASH LINK MOBILE 1x FLASH LINK MOBILE APP Smartphone AndroId or iOS with Internet 1x connection (provider charges may apply). Téléphone Intelligent Android ou iOS avec connection Internet (frais du fournisseur Internet peuvent s'appliquer). MANDATORY | OBLIGATOIRE HOOD PIN CONTACT DE CAPOT REMOTE START SAFETY OVERRIDE SWITCH COMMUTATEUR DE SÉCURITÉ DE DÉSACTIVATION DU DÉMARREUR À DISTANCE ON VALET SWITCH COMMUTATEUR VALET OFF Part #: RSPB available, Sold separately. Pièce #: RSPB disponible, vendu séparément. Page 2 / 9 Notice: the installation of safety elements are mandatory. The hood pin and the valet switch are essential security elements and must be installed. Notice: l'installation des éléments de sécurité est obligatoire. Le contact de capot et le commutateur de valet sont des éléments de sécurité essentiels et doivent absolument être installés. STAND ALONE CONFIGURATION | CONFIGURATION EN DÉMARREUR AUTONOME Program bypass option OEM Remote Stand Alone Remote Starter: Programmez l'option du contournement Démarreur à distance Autonome avec télécommande d'origine : Program bypass option with oem remote: Programmez l'option du contournement avec télécommande d'origine: UNIT OPTION OPTION UNITE OR D1.10 OU D1.1 UN UNIT OPTION OPTION UNITE C1 Program bypass option with RF KIT antenna: Programmez l'option du contournement avec antenne RF: UNIT OPTION OPTION UNITE H1 to H6 H1 à H6 DESCRIPTION By default, LOCK, LOCK, LOCK Par défaut, VERROUILLE,VERROUILLE,VERROUILLE LOCK, UNLOCK, LOCK VERROUILLE,DÉVERROUILLE,VERROUILLE DESCRIPTION OEM Remote Monitoring Supervision de la télécommande d'origine DESCRIPTION Supported RF Kits and select RF Kit Kit RF supportés et sélectionnez le KIT RF REMOTE STARTER FUNCTIONALITY | FONCTIONNALITÉS DU DÉMARREUR À DISTANCE 3X All doors must be closed. Toutes les portes doivent être fermées Press the OEM remote's Lock button 3x to remote-start (or remote-stop) the vehicle. Appuyez sur le bouton Verrouillage 3X de la télécommande d'origine pour démarrer à distance (ou arrêter à distance) le véhicule. START The vehicle will START. Le véhicule DÉMARRE. REMOTE STARTER DIAGNOSTICS DIAGNOSTIQUE DU DÉMARREUR À DISTANCE MODULE RED LED | DEL ROUGE DU MODULE x2 flash : Brake ON Frein Activé x3 flash : No tach Pas de Tach x4 flash : Ignition Clé de contact before start détectée avant démarrage x5 flash : Hood Open Capot Ouvert REMOTE STARTER WARNING CARD | CARTE D'AVERTISSEMENT DE DÉMARREUR À DISTANCE WARNING | ATTENTION CUT THIS WARNING CARD AND STICK IT ON A VISIBLE PLACE: or use the package RSPB, Sold separately. COUPEZ CETTE CARTE D'AVERTISSEMENT ET COLLEZ-LA À UN ENDROIT VISIBLE: ou utilisez la trousse RSPB, vendue séparément. REMOTE STARTER DÉMARREUR À DISTANCE THE VEHICLE CAN BE STARTED BY EITHER: PRESSING THE LOCK BUTTON ON THE OEM REMOTE 3 TIMES CONSECUTIVELY OR BY A SMARTPHONE. TURN ON THE SAFETY SWITCH LOCATED UNDER THE DASHBOARD BEFORE WORKING ON THE VEHICLE. LE VÉHICULE PEUT DÉMARRER SOIT: EN APPUYANT 3 FOIS CONSÉCUTIVEMENT SUR LE BOUTON VERROUILLAGE DE LA TÉLÉCOMMANDE DU VÉHICULE OU PAR UN TÉLÉPHONE INTELLIGENT. ACTIONNEZ EN POSITION `ON' LE COMMUTATEUR DE SÉCURITÉ SITUÉ SOUS LE TABLEAU DE BORD AVANT LES TRAVAUX D'ENTRETIEN. NOTES This guide may change without notice. See www.fortin.ca for latest version. Ce guide peut faire l'objet de changement sans préavis. Voir www.fortin.ca pour la récente version. Page 3 / 9 ATTENTION WARNING Disconnect the negative (-) battery post before proceding with the installation and reconnect it after making sure all vehicle connectors are reconnected. ATTENTION Débrancher le négatif (-) de la batterie du véhicule avant de procéder a l'installation et rebrancher lorsque tous les connecteurs du véhicule sont rebranché. Vehicle battery Batterie du véhicule Disconnect the (-) terminal of the battery. Débranchez le borne négative de la batterie du véhicule. CONTINUED NEXT PAGE | CONTINUEZ À LA PAGE SUIVANTE This guide may change without notice. See www.fortin.ca for latest version. Ce guide peut faire l'objet de changement sans préavis. Voir www.fortin.ca pour la récente version. DESCRIPTION | DESCRIPTION Page 4 / 9 3 Remove the battery from the key fob. Retirez la batterie de la télécommande. + 3 Key control Contrôle de la clé 3 This installation is easier with a transponder antenna* (*Part #: ARE-1R0, Sold separately). Cette installation est simplifiée avec une antenne transpondeur* (*Part #: ARE-1R0, vendu séparément). Back of Key fob. Dos de la télécommande. Remove the adhesive from the back of the antenna ring* and stick it on the back of the key fob. Collez l'antenne* auto-collante au dos de la télécommande et coller au dos de la télécommande comme montré. OR OU 3 Make 5 to 10 loops with a 22 gauge wire on the back of the key fob. Faire 5 à 10 tours avec un fil de calibre 22 au dos de la clé télécommande. Back of Key fob. Dos de la télécommande. This guide may change without notice. See www.fortin.ca for latest version. Ce guide peut faire l'objet de changement sans préavis. Voir www.fortin.ca pour la récente version. DESCRIPTION | DESCRIPTION Page 5 / 9 Gateway Module, above gas pedal . 2 Au Module Gateway, au dessus de la pédale à gaz. X2 Pink connector Connecteur Rose X2 1 A (-) PARKING LIGHTS (MUX) PTS (DATA) CANLOW1 (DATA) CAN HIGH 1 BCM, above driver kick panel 1 BCM, au dessus du panneau latéral côté conducteur X1 X2 X3 X4 X5 X6 X7 X8 X4 Gray connector Connecteur Gris X4 1B (+) 12V (-) LIGHTS OFF X5 Green connector Connecteur Vert X5 1 C (MUX) BRAKE (DATA) LOCK (-) GROUND (DATA) IMMO X8 Dark Gray connector Connecteur Gris foncé X8 1E (DATA) REMOTE DETECTION This guide may change without notice. See www.fortin.ca for latest version. Ce guide peut faire l'objet de changement sans préavis. Voir www.fortin.ca pour la récente version. Page 6 / 9 AUTOMATIC TRANSMISSION WIRING CONNECTION | SCHÉMA DE BRANCHEMENT TRANSMISSION AUTOMATIQUE Hood pin only required on vehicles not equipped with a factory hood pin. Commutateur de capot requis seulement si le véhicule n'est pas équipé de cette composante. SAFETY OVERRIDE SWITCH COMMUTATEUR DE SÉCURITÉ OPTIONAL RF KIT KIT RF OPTIONNEL WITH RF-KIT AVEC KIT-RF Start / Stop external control Contrôle de démarrage/arrêt externe (-) Lock/Unlock input external control | Contrôle du (-) verrouillage devérrouillage entrée externe WITHOUT RF-KIT: SANS KIT RF: RF-KIT REMOTE STARTER KIT-RF DÉMARREUR À DISTANCE WITH | AVEC DATA-LINK: Direct connection Branchement directe RS6 (+)IGNITION MAY BE REQUIERED - PEUX ÊTRE REQUIS RS2 IN (+)12V Battery RS1 Ground | Masse B4 Red (+)12V Battery B3 Black Ground | Masse Cut | Coupez Red B4 Cut | Coupez Black B3 Blue B2 White B1 B Yellow In AA11 (-) Lock Purple In AA22 (-) Unlock Purple/White In AA33 Green Out AA44 (-)Tailgate White Out AA55 Orange In AA66 A Orange/Black Hood pin Dk.Blue In AA77 In AA88 Red/Blue In AA99 (~) Remote Detection Lt.Blue/Black A1100 Black Out AA1111 Pink Out A1122 Start/Stop external Yellow/Black In A1133 (-)Parking Lights Brown/White Out A1144 (-)Lights OFF Pink/Black Out A1155 (+) IGNITION OUT Purple/Yellow OUT A1166 Green/White A1177 (MUX)Brake Green/Red A1188 (MUX)PTS White/Black A1199 (DATA)Door Lock Lt.Blue A2200 C55 Brown C44 Gray/Black CAN LOW C33 Gray CAN HIGH C C22 Orange/Brown C11 Orange/Green D6 White/Red D D5 White/Blue D4 White/Green D3 Yellow/Red D2 Yellow/Blue D1 Yellow/Green (DATA)Door Lock (DATA)Door Lock (DATA)IMMO ARE-1R0 (DATA)IMMO/ARE-1R0 SILVERADO CUT CUT 1.5 K Ohm 1AMP Fuse Fusible D1 D4 Resistor/Résistance Diode 7.5Amp. A15 (-) LIGHTS OFF Green/ Brown Vert/ Brun (-) PARKING LIGHTS A19 (MUX) PTS Green/ Gray Vert/ Gris Blue/ Green Bleu/ Vert RS1 OR B3 (-) GROUND RS2 OR B4 (+) 12V D3 (~) IMMO Black Noir Red/ White Rouge/ Blanc White/ Grey Blanc/ Gris D1 ARE -1R0 Purple/ White Mauve/ Blanc D2 ARE -1R0 Purple Mauve A18 (MUX) BRAKE Blue/ Yellow Bleu/ Jaune A20/D6 (~) DOOR LOCK Green/ Yellow Vert/ Jaune A5 A10 (-) TAILGATE (~) REMOTE DETECTION Brown Brun Green/Yellow Vert/Jaune C3 (~) CAN HIGH 1 Blue/ White Bleu/ Blanc C4 (~) CAN LOW1 Blue/ Yellow Bleu/ Jaune 26 19 12 27 20 13 28 21 14 29 22 15 30 23 16 31 24 17 32 25 18 51 6 72 8 93 10 11 4 15 8 1 24 16 9 2 22 17 10 3 25 18 11 4 23 19 12 20 13 5 6 21 14 7 1A X2 Pink connector Connecteur Rose X2 1B X4 Gray connector Connecteur Gris X4 3 See previous page Voir page précédente 1 ADB C E 1 2 X1 X2 X3 X4 X5 X6 X7 X8 BCM, above driver kick panel BCM, au dessus du panneau latéral côté conducteur 23 16 9 5 1 24 17 10 25 18 11 6 2 26 19 12 27 20 13 7 3 28 21 14 29 22 15 8 4 23 16 9 5 1 24 17 10 25 18 11 6 2 26 19 12 27 20 13 7 3 28 21 14 29 22 15 8 4 1C X5 Green connector Connecteur Vert X5 26 19 12 5 1 27 20 13 6 28 21 14 7 2 29 22 15 8 30 23 16 9 3 31 24 17 10 32 25 18 11 4 1D X3 Blue connector Connecteur Bleu X3 1E X8 Dark Gray connector Connecteur Gris foncé X8 123456 11 12 13 14 15 16 21 22 23 24 25 26 78 17 18 27 28 9 10 19 20 29 30 2 Back view Black 30-pin connector At Gateway Module, above gas pedal. Vue de dos Connecteur Noir de 30-pins Au Module Gateway, au dessus de la pédale à gaz. This guide may change without notice. See www.fortin.ca for latest version. Ce guide peut faire l'objet de changement sans préavis. Voir www.fortin.ca pour la récente version. PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION Page 7 / 9 1 x1 HOLD 2 RELEASE ON BLUE BLEU Press and hold the programming button: Connect the 4-Pin Data-link connector. Appuyez et maintenir enfoncé le bouton de programmation: Branchez le connecteur Data-Link à 4-Broches. The BLUE, RED, YELLOW and BLUE & RED LEDs will alternatively illuminate. Les DELs BLEUE, ROUGE, JAUNE et BLEUE & ROUGE s'allumeront alternativement. Release the programming button when the LED is BLUE. Relâchez le bouton de programmation quand la DEL est BLEU. If the LED is not solid BLUE disconnect the 4-Pin connector (Data-Link) and go back to step 1. Si le DEL n'est pas BLEU débranchez le connecteur 4 pins (Data-Link) et allez au début de l'étape 1. 3 Insert the required remaining connectors. Insérez les connecteurs requis restants. 4 x1 PRESS HOLD 5 SEC. 5 IGN ON x1 PRESS 6 x1 PRESS OFF IGNITION OFF ON IGNITION ON ON Press and hold the Push-to-Start button until the ignition turn ON. Appuyez et maintenez enfoncé le bouton démarrage (Push-to-Start) jusqu'à ce que l'ignition s'allume. IGNITION ON PRESS X1 ON OFF WAIT FLASH RAPIDLY Press and release the programming button once (1x). The BLUE LED will turn off. Wait, The BLUE LED will flash rapidly. Appuyez et relâchez 1 fois le bouton de programmation. La DEL BLEUE s'éteint. Attendre, La DEL BLEU clignotera rapidement. IGNITION ON IGNITION OFF OFF Press the Push-to-Start button once to turn off the ignition. The BLUE LED will turn off. Appuyez 1 fois sur le bouton démarrage (Push-to-Start) pour éteindre l'ignition. La DEL BLEUE s'éteint. The module is now programmed. Le module est programmé. This guide may change without notice. See www.fortin.ca for latest version. Ce guide peut faire l'objet de changement sans préavis. Voir www.fortin.ca pour la récente version. FUNCTIONS | FONCTIONS Page 8 / 9 START UNLOCK All doors must be closed. Toutes les portes doivent être fermées Remote start the vehicle. Démarrez à distance. Unlock the doors with either: · the remote-starter remote · the proxy remote. Déverrouillez les portes avec soit: · la télécommande du démarreur à distance, · la télécommande proxy d'origine. Enter the vehicle with the SMART-KEY. Entrez dans le véhicule avec la clé intelligente (SMART-Key) sur vous Press the brake pedal. Appuyez sur la pédale de frein. The vehicle can now be put in to gear and driven. Vous êtes maintenant prêt à embrayer et prendre la route. OFF The engine will shutdown when a door is open if the vehicle is not Unlock. Le moteur va s'éteindre à l'ouverture de la porte si le véhicule n'est pas déverrouillé. t. PUSH Page 9 / 9 ALL MODEL: EVO-ALL DATE:02/2019 FORTIN.CA SN: 000000 00000 MADE IN CANADA © 2018 ALL RIGHTS RESERVED Module label | Étiquette sur le module Notice: Updated Firmware and Installation Guides Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product. Notice: Mise à jour microprogramme et Guides d'installations Des mises à jour du Firmware (microprogramme) et des guides d'installation sont mis en ligne régulièrement. Vérifiez que vous avez bien la dernière version logiciel et le dernier guide d'installation avant l'installation de ce produit. WARNING The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version. MISE EN GARDE L'information de ce guide est fournie sur la base de représentation (telle quelle) sans aucune garantie de précision et d'exactitude. Il est de la seule responsabilité de l'installateur de vérifier tous les fils et circuits avant d'effectuer les connexions. Seuls une sonde logique ou un multimètre digital doivent être utilisés. FORTIN SYSTÈMES ÉLECTRONIQUES n'assume aucune responsabilité de l'exactitude de l'information fournie. L'installation (dans chaque cas) est la responsabilité de l'installateur effectuant le travail. FORTIN SYSTÈMES ÉLECTRONIQUES n'assume aucune responsabilité suite à l'installation, que celle-ci soit bonne, mauvaise ou de n'importe autre type. Ni le manufacturier, ni le distributeur ne se considèrent responsables des dommages causés ou ayant pu être causés, indirectement ou directement, par ce module, excepté le remplacement de ce module en cas de défectuosité de fabrication. Ce module doit être installé par un technicien qualifié. L'information fournie dans ce guide est une suggestion. Ce guide d'instruction peut faire l'objet de changement sans préavis. Consultez le www.fortinbypass.com pour voir la plus récente version. Copyright © 2006-2019, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING TECH SUPPORT Tél: 514-255-HELP (4357) 1-877-336-7797 ADDENDUM GUIDE www.fortinbypass.com WEB UPDATE | MISE À JOUR INTERNET