electronics.de
mailto:info@tls-electronics.de
TLS electronics GmbH, Hilden
User Manual for TLS electronics models including: 875150, HDBaseT Set 100 HDMI USB RS232 IR
875150 HDBaseT Set 100 HDMI USB RS232 IR Relens GmbH Contact: info@tls-electronics.de 3 Thank you for purchasing this product.
875150 HDBaseT Set 100 HDMI USB RS232 IR Relens GmbH Contact: info@tls-electronics.de 5 Features
HDBaseT Set
File Info : application/pdf, 16 Pages, 488.30KB
DocumentDocumentUser manual 875150 HDBaseT Set 100 HDMI USB RS232 IR 875150 HDBaseT Set 100 HDMI USB RS232 IR Table of contents Table of contents................................................................................................ 2 Safety and Notice .............................................................................................. 3 Introduction ........................................................................................................ 4 Applications ....................................................................................................... 4 System Requirements ....................................................................................... 4 Features............................................................................................................. 5 Panel Description............................................................................................... 6 Transmitter Front ............................................................................................ 6 Transmitter Rear ............................................................................................. 7 Receiver Front ................................................................................................ 8 Receiver Rear ................................................................................................. 9 Connection Diagram ........................................................................................ 10 Specifications................................................................................................... 11 Firmware Update: ............................................................................................ 12 Package Contents ........................................................................................... 13 Maintenance .................................................................................................... 13 Warranty Policy................................................................................................ 13 Limitations of Warranty .................................................................................... 14 Exclusive Remedies ........................................................................................ 14 RMA Policy ...................................................................................................... 15 Standard Replacement .................................................................................... 15 Once you have obtained an RMA number....................................................... 15 Please note: ..................................................................................................... 16 Warranty .......................................................................................................... 16 Return and RMA Policies................................................................................. 16 Relens GmbH Contact: info@tls-electronics.de 2 875150 HDBaseT Set 100 HDMI USB RS232 IR Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. SURGE PROTECTION DEVICE RECOMMENDED This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lightning strikes, etc. Use of surge protection systems is highly recommended in order to protect and extend the life of your equipment. Safety and Notice 1) The transmission distances of HDMI over UTP cables are measured using TE CONNECTIVITY 1427071-6 2) EIA/TIA-568-B termination for CAT cables is recommended for better performance. 3) DO NOT use 568A/568B standard mixed CAT cable (cross-over cable) because there are 2 pairs swapped, this will make POE OVER-CURRENT and damage POE components. Please use straight-through CAT cable (both RJ45 headers are 568A or 568B standard). 4) It is recommended that power up the device after connections of source, sink and CAT cable. 5) To reduce the interference among the unshielded twisted pairs of wires in CAT cable, do not run HDBaseT / Zone Cat5e/6/6a cabling with or in close parallel proximity to mains power cables. Shielded CAT cables can be used to improve EMI problems, which is worsen in long transmission. 6) Because the quality of the CAT cables has the major effect on how long the transmission limit can achieve and how good is the received picture quality, the actual transmission range is subject to one's choice of CAT cables. 7) Do not substitute or use any other Power Supply other than the enclosed unit, or a TLS approved Replacement Part. Doing so will void the warranty and potentially expose the user to dangerous voltages resulting in an electrical shock. 8) Do not disassemble the device for any reason. Doing so will void the manufacturer's warranty. Also, our unique case is an integral part of the design of this unit and is responsible for cooling and circuitry shielding. Any modifications to this case will potentially cause malfunction and product failure. 9) Do not expose the device to water, moisture, or liquids. Possible electric shock may result as well as failure of the unit to operate. Relens GmbH Contact: info@tls-electronics.de 3 875150 HDBaseT Set 100 HDMI USB RS232 IR Introduction This Model allows HDMI signals to be transmitted over a Single CAT5e/6 cable. This solution has the added features of RS232 and 2-way IR control functionality over the same CAT5e/6 cable. It can extend 4K@60Hz YUV4:4:4 over a HDBaseT link and upto 100M.The slimmest HDBaseT design, making it perfect to mount behind ultra thin TVs. Note: 1) About POC The POC function is designed for powering compatible TX or RX unit of TLS ONLY. DO NOT connect it with any third party Power Over Ethernet devices. Damage may result. Applications Household entertainment sharing and control Lecture room display and control Showroom display and control Meeting room presentation and control Classroom display and control System Requirements Input HDMI source equipment such as DVD/Blu-ray player,host PC/Laptop and HDMI Equipped output display (TV or monitor) with amplifier or active speakers. Relens GmbH Contact: info@tls-electronics.de 4 875150 HDBaseT Set 100 HDMI USB RS232 IR Features Bandwidth up to 18Gbps, resolution up to 4K2K@60hz YUV 4:4:4 Transmit up to 150m under 1080p,100m under 4K Support HDR10 Support KVM and USB2.0 Support Bi-directional wide band IR and RS232 Pass through Support Dual POC (Receiver powered by transmitter or transmitter powered by Receiver) Support HDCP2.2/ HDCP1.4 Compliant Support Copy local and remote EDID functionality Supports audio extractor rate up to 192kHz Support PCM7.1, Dolby, DTS With micro USB port for firmware upgrade Relens GmbH Contact: info@tls-electronics.de 5 875150 HDBaseT Set 100 HDMI USB RS232 IR Panel Description Transmitter Front IR In: Connect to the supplied IR blaster cable for IR signal transmission. Place the IR blaster in direct line-of-sight of the equipment to be controlled. IR Out: Connect to the supplied IR blaster cable for IR signal transmission. Place the IR blaster in direct line of sight of the equipment to be controlled. USB Type A for extension USB Type B for connection DIP Switch: Switch to" 0 "transmit upto 100m under 4K@60Hz. Switch to"1"transmit upto 150m under 1080P@60Hz.(Before power on, TX and RX must be selected to 0 or 1 at the same time. Please do not switch it in the working process) EDID Switch: Switch to"0"copy EDID from display of receiver(remote EDID mode).Switch to"1"copy EDID from loopout display of transmitter(local EDID mode). Indicator of HDMI Indicator of power input Note: EDID copy function on transmitter do not support 150M long distance, when it is long distance mode, the EDID only support 1080P@60Hz. Relens GmbH Contact: info@tls-electronics.de 6 875150 HDBaseT Set 100 HDMI USB RS232 IR Transmitter Rear DC 24V input Update: USB port to update the firmware RS232 in: Connect to a PC or laptop with phoenix terminal for the transmission of RS232 commands HDBT out: Connect to the receiver unit with a single CAT5e/6 cable for transmission of all data signals HDMI loop out: Connect to a HDMI equipped TV/Monitor for display of the HDMI input source signal HDMI In: Connect to HDMI source equipment such as DVD or Blu-ray player Note: do not connect projector directly which will break HDBT port, please contact us and require technical support for such application. Relens GmbH Contact: info@tls-electronics.de 7 Receiver Front 875150 HDBaseT Set 100 HDMI USB RS232 IR IR Out: Connect to the supplied IR blaster cable for IR signal transmission. Place the IR blaster in direct line of sight of the equipment to be controlled. IR In: Connect to the supplied IR blaster cable for IR signal transmission. Place the IR blaster in direct line-of-sight of the equipment to be controlled. USB Type A for extension DIP Switch: Switch to"0"transmit upto 100m under 4K@60Hz. Switch to"1"transmit upto 150m under 1080P@60Hz.(Before power on, TX and RX must be selected to 0 or 1 at the same time. Please do not switch it in the working process) Audio Switch: Switch to"0"extract Audio and output.Switch to"1"close extraction Audio output(analog audio and SPDIF). Indicator of HDMI Indicator of power input Relens GmbH Contact: info@tls-electronics.de 8 875150 HDBaseT Set 100 HDMI USB RS232 IR Receiver Rear DC 24V input Update: USB port to update the firmware RS232 Out: Connect to the device that is to be controlled via phoenix terminal by RS-232 commands HDBT in: Connect to the transmitter unit with a single CAT5e/6 cable for transmission of all data signals HDMI output: Connect to a HDMI equipped TV/Monitor for display of the HDMI input source signal SPDIF out Analog audio out Relens GmbH Contact: info@tls-electronics.de 9 875150 HDBaseT Set 100 HDMI USB RS232 IR Connection Diagram Relens GmbH 10 Contact: info@tls-electronics.de 875150 HDBaseT Set 100 HDMI USB RS232 IR Specifications Operating Temperature Range -5 to +40°C (23 to +104 °F) Operating Humidity Range 5 to 90 % RH (no condensation) Input Video Signal 0.5-1.0 volts p-p Input DDC Signal 5 volts p-p (TTL) Video Format Supported DTV/HDTV; 4K/1080P/1080i/720P(50HZ)/576P/48 0P/576i/480i Output Video HDMI 2.0+HDCP1.4/2.2 Output Audio Support PCM,DTS-HD, Dolby-HD Maximum Distance Transmission 150 meters for 1080P, 100 meters for 4K Power Supply 24V1A Poc Power from TX to RX over Cat5/6 cable Power Consumption Dimensions 14Watts 172.4mmH×113.2mmW×24mmD Mass (Main unit) 1.1Kg (Pairs) NOTE: Specifications are subject to change without notice. Weight and dimensions are approximate. Relens GmbH Contact: info@tls-electronics.de 11 875150 HDBaseT Set 100 HDMI USB RS232 IR Firmware Update: The user should use the CD in colorbox,read and install software in PC; Connect unit to PC with usb cable from micro usb port, click software to select correct usb port: (Note: if PC is unable to identify the correct usb port,please install the driver from CD first) Type in "A2" in PORT and select PATH with update file then click UPDATA wait for update till display "Succeed" in red frame: (Note:please differentiate the firmware for TX and RX before upgrade) Relens GmbH 12 Contact: info@tls-electronics.de 875150 HDBaseT Set 100 HDMI USB RS232 IR Package Contents Main unit 24V1A DC power supply 1xIR TX unit 1xIR RX unit 2 Phoenix plugs for RS232 cable termination 1 USB-cable A-B 1 USB micro cable 2 mounting brackets Maintenance Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner or benzene to clean this unit. Warranty Policy TLS electronics products are warranted against defects in material and workmanship for two years from the date of shipment. During the warranty period, TLS electronics will, at its option, repair or replace products that prove to be defective. Repairs are warranted for the remainder of the original warranty or a 90 day extended warranty, whichever is longer. For equipment under warranty, the owner is responsible for freight to TLS electronics and all related customs, taxes, tariffs, insurance, etc. TLS electronics is responsible for the freight charges only for return of the equipment from the factory to the owner. TLS electronics will return the equipment by the same method (i.e., Air, Express, Surface) as the equipment was send to TLS electronics. All equipment returned for warranty repair must have a valid RMA number issued prior to return and be marked clearly on the return packaging. TLS electronics strongly recommends all equipment be returned in its original packaging. TLS electronics obligations under this warranty are limited to repair or replacement of failed parts, and the return shipment to the buyer of the repaired or replaced parts. Relens GmbH Contact: info@tls-electronics.de 875150 HDBaseT Set 100 HDMI USB RS232 IR Limitations of Warranty The warranty does not apply to any part of a product that has been installed, altered, repaired, or misused in any way that, in the opinion of TLS electronics, would affect the reliability or detracts from the performance of any part of the product, or is damaged as the result of use in a way or with equipment that had not been previously approved by TLS electronics. The warranty does not apply to any product or parts thereof where the serial number or the serial number of any of its parts has been altered, defaced, or removed. The warranty does not cover damage or loss incurred in transportation of the product. The warranty does not cover replacement or repair necessitated by loss or damage from any cause beyond the control of TLS electronics, such as lightning or other natural and weather related events or wartime environments. The warranty does not cover any labor involved in the removal and or reinstallation of warranted equipment or parts on site, or any labor required to diagnose the necessity for repair or replacement. The warranty excludes any responsibility by TLS electronics for incidental or consequential damages arising from the use of the equipment or products, or forany inability to use them either separate from or in combination with any other equipment or products. A fixed charge established for each product will be imposed for all equipment returned for warranty repair where TLS electronics cannot identify the cause of the reported failure. Exclusive Remedies TLS electronics's warranty, as stated is in lieu of all other warranties, expressed, implied, or statutory, including those of merchantability and fitness for a particular purpose. The buyer shall pass on to any purchaser, lessee, or other user of TLS electronics's products, the aforementioned warranty, and shall indemnify and hold harmless TLS electronics from any claims or liability of such purchaser, lessee, or user based upon allegations that the buyer, its agents, or employees have made additional warranties or representations as to product preference or use. The remedies provided herein are the buyer's sole and exclusive remedies. TLS electronics shall not be liable for any direct, indirect, special, incidental, or consequential damages, whether based on contract, tort, or any other legal theory. Relens GmbH 14 Contact: info@tls-electronics.de 875150 HDBaseT Set 100 HDMI USB RS232 IR RMA Policy When returning product to TLS electronics for any reason, the customer should fill out the official RMA form to obtain a RMA number. Without the permission or approval, TLS electronics will be no responsible for any return. This can be initiated by emailing or calling your related sales. All requests are processed within 48 hours. Standard Replacement For customers that agree to return defective product to TLS electronics first, a Standard Replacement option is available. An RMA number must first be issued by sales. This RMA number will need to be referenced on the outside of the return shipment. Upon receipt of the defective product, TLS electronics will, at its discretion, either repair or replace the product and ship it out in the most expeditious manner possible. Subject to availability, the replacement product will be shipped on the business day following receipt of the defective product. In the event the product returned to TLS electronics has been discontinued (i.e. the product is no longer being manufactured by TLS electronics but is still under warranty), TLS electronics will, at its discretion, either repair or replace with recertified product. Once you have obtained an RMA number After obtaining an RMA number from TLS electronics, you must send the product - freight prepaid - to TLS electronics. The TLS electronics RMA number must be prominently displayed on the outside of your package. If you send your product to TLS electronics without the RMA number prominently displayed on the outside of the package, it will be returned to you unopened. Please use a shipping company that can demonstrate proof of delivery. TLS electronics does not accept responsibility for any lost shipments unless proof of delivery to TLS electronics is provided. Relens GmbH Contact: info@tls-electronics.de 875150 HDBaseT Set 100 HDMI USB RS232 IR Please note: Product shipped to TLS electronics must be properly packaged to prevent loss or damage in transit. Shipping your RMA to TLS electronics using regular mailing envelopes is not acceptable, as they do not protect the product from damage during shipping. TLS electronics will not repair or replace a module that is shipped in such a way that the product is not properly protected. TLS electronics will not accept any product that has been damaged as a result of accident, abuse, misuse, natural or personal disaster, or any unauthorized disassemble, repair or modification. Warranty Warranty time is two year and from the date of original shipment. This warranty shall be void if a serial number has been removed from the product. Upon determination of a legitimate defect covered by this warranty and at TLS sole discretion, user should bear the transport cost during the warranty. If product is out of warranty then repair charge is required. Minimum repair charge: 10% of the retail price plus the cost of failed components. We will repair the failed product after repair cost has been approved by Customers and proper financial arrangements are made. Customer must cover round trip shipment expenses. Return and RMA Policies Shipments will not be receiver and processed for warranty repair/replacement without an TLS electronics RMA(Return Materials Authorization). Relens GmbH Germany 33175 Bad Lippspringe An der Eiche 4 +49 (05252) 270 info@tls-electronics.de www.tls-electronics.de Relens GmbH 16 Contact: info@tls-electronics.de