User Manual for ATEC IOT models including: TWZT-S001D-P Pole Zigbee Module, TWZT-S001D-P, Pole Zigbee Module, Zigbee Module, Module
ATEC IOT CO.LTD TWZT-S001D-P 2AZKWTWZT-S001D-P 2AZKWTWZTS001DP twzt s001d p
CUSTOMER : Standard .
CUSTOMER : Standard
DATE
: 2019,06.10 .
DATE
: 2023. 04. 01
REV
: 0.4
.
SPEPCRIFOIDCUATCITONSPSEFCOIFRICAAPTPIROONVAL
TWZT-S001D-P
Model Pole Zigbee Module
Part Number TWZT-S001D-P
Customer P/N -
APPROVAL REMARK APPENDIX
DESIGNED
2023.01.26 J.B.KIM
CHECKED
2023.01.26 J.S.YEON
APPROVED
2023.01.26 I.U.KIM
MODEL REG. DATE REV. DATE
SPECIFICATION
TWZT-S001D-P
REV. No.
2023.04.01
PAGE
-
-
Revision History
Revision Date
Contents of Revision Change
0.0 2023.04.01 Initial Release
Rev. 0.1 31 -
Remark
J.B. Kim
1 / 12
TABLE OF CONTENTS
1. Application 2. Quality 3. Appearance and Characteristics 4. Overall Service Scenario 5. General Features 6. Absolute Maximum Rating 7. Electrical Specification 8. Mechanical Information 9. User Quick Manual 11. Disclaimers
3/15 3/15 3/15 4/15 5/15 7/15 8/15 12/15 14/15 15/15
2 / 12
1. Application
This Specification is applied to ATEC IoT Pole Zigbee Module(TWZT-S001D-P). TWZT-S001D-P is Common Zigbee Module solution for IEEE 802.15.4(6LoWPAN) applications. The robust network with PA(Power Amplifier) and diverse interface(SPI, UART, I2C) make it possible to be used as various kinds of applications. Specially, it is suitable for Gen2 Gateway and RTLS Anchor. TWZT-S001D-P is composed of RF IC and necessary external component include the Dipole Ant.
2. Quality
Quality should meet each condition which mentioned on this specification. However, the items which are not mentioned on this specification follow the inspection agreements and standards which are agree with both companies.
3. Appearance and Characteristics
3.1. Appearance
Appearance should not be contaminated by harmful materials and should not have cracks, etc. Mechanical dimensions should meet the contents of clause 8.
3.2. Characteristic
Electrical Characteristics should meet the contents of clause 7.
3 / 12
4. Overall Service Scenario
POS
Server
ESL EMS(1)
Wired
· WiFi / Ethernet · IEEE802.15.4 · 2,000 Tags per GW
GATEWAY
· One Platform & Integrated Gateway
Wireless & Bi-Directional
2.4GHz Wireless Tags (Battery / Power Line)
(1) EMS : ESL Management Software 4 / 12
5. General Features
5.1. Description Item Size Weight
Memory
Description 42.3 x 28.0 x 9.8 (mm) Typ. 6g
Internal Flash : 512KB SRAM : 32KB
Power
Operating Voltage : Typ. 3.3V (2.3V~3.6V)
Tx Power
RF
Data Rate
Antenna
20pin Interface
Network
Wireless
Security Protocol Comm. Range
Max.10dBm
250kbps
Dipole Antenna UART for FW Downloading SPI for Communication 2.4GHz IEEE802.15.4 compliant RF Transceiver Range Extender (PA/LNA) Robust wireless network (ATEC IoT own protocol) Compatible with ATEC IoT protocol communication devices Max. 30m (under LoS) (1)
(1) LoS (Line of Sight) : Without any sort of an obstacle between a gateway and end devices
5 / 12
6. Absolute Maximum Rating
6.1. Environmental Conditions
The normal operating environmental conditions are those as below. In such conditions, ESL must be in conformity with the present specification. The conformity to such requirement must be certified by the manufacturer.
Parameter Operating Environment
Storage Environment
[Notice]
Condition Temperature
Humidity Temperature
Humidity
Min. -20
-30
-
Typ. 35 35
Max. 85 80 85 80
Unit
%RH
%RH
* TWZT-S001D-P is design to be used indoor/Ceiling. It does not guarantee outdoor
conditions.
6.2. Electrical Conditions
The operating electrical conditions are those as below. In such conditions the ESL must be in conformity with the present specification. All devices can be damaged or non-operated over the specification as below.
The conformity to such requirement must be certified by the manufacturer.
Parameter Supply Voltage
Power Consumption
Condition DC Power Supply @ 3.0~3.3V (Active Tx) @ 3.0~3.3V(Active Rx)
Min
Typ.
Max
Unit
2.3
3.3
3.6
V
-
-
200
mA
-
-
15
mA
ESD Protection
HBM(150pF/330) (1) Air Condition @Soft Fail
-8
-
+8
kV
[Notice] (1) TWZT-S001D-P is ESD sensitive device. Precaution should be used when handling the device in order to prevent permanent damage.
7 / 12
7. Electrical Specification
7.1. IEEE802.15.4
The TWZT-S001D-P supports IEEE802.15.4.
7.2. General Specification
· Standard : Only IEEE802.15.4 PHY · Frequency : 2405 ~ 2480MHz · Channel : 16CH. (5MHz Spacing) · Modulation : DSSS/O-QPSK · Max. Data Rate : 250Kbps
7.3. Electrical Specification
· Channel power depend on each country regulations (EX. KC, etc) · The electrical specification which is shown below is ATEC IoT internal specification. · All values depend on surrounding environment and current statement of access point
RF Performance
Parameter
Condition
Min
Typ
Max
Unit
Output Power
-
-
10
dBm
Receiver Sensitivity PER=1% (Required -85dBm)
-85
-
-
dBm
Maximum Input Level PER=1% (Required -20dBm)
-
-
-20
dBm
Frequency Tolerance
Required Max. ±75kHz
-75
-
75
kHz
Error Vector Magnitude
Required Max. 35%
-
-
35
%
8 / 12
7.4. Antenna Performance
7.4.1 Antenna
The TWZT-S001D-P supports IEEE802.15.4. Radiation Pattern and Gain
TEST METHOD
Network Analyzer Signal Interface : Coaxial Cable Test Antenna Dual Polarized Antenna Shield Room
Radiation Pattern 2405 MHz
2440 MHz
2480 MHz
Efficiency
Frequency(MHz) Efficiency(dB) Peak Gain(dB)
2405 -3.92 -0.36
2440 -3.55 0.41
2480 -4.27 -0.35
[Notice] * This data is measured when TWZT-S001D-P is connected to the 4th Slot of Gen2 Gateway Board. Gen2 Gateway has 7 slots for diverse modules. The 4th Slot is the middle slot of whole 7 slots of it.
9 / 12
7.4. Antenna Performance 7.4.2 Gen2 Gateway Slot Information
Slot#3
Slot#4
This Location is recommended IR-UWB Module
Slot#5
Slot#2 Slot#1
ATEC IoT
Slot#6 Slot#7
SSD Memory (Back Case)
USB DC Input
Button LAN Input
LED Indicator
Expandable Slot (SPI I/F)
Expandable Slot (UART&I2C I/F)
10 / 12
7.5. Interface Information
Top side No.20
Bottom side No.10
No.11
No.1
#
Name
I/O
Description
1
GND
G
Common ground
2
SPI_CS
O
Enable input for SPI interface
3
SPI_MISO
I
SPI data input
4
WAKE UP
O
wake up signal
5
UART_TX
I
NC
6
UART_RX
O
NC
7
VDD
P
3.3V external DC supply
8
VDD
P
3.3V external DC supply
9
GND
G
Common ground
10
GND
G
Common ground
11
GND
G
Common ground
12
NC
-
NC
13
TEST_PIN
O
Firmware Download Enable Pin
14
GND
G
Common ground
15
RESET
I
Reset input/output(active low)
16
IRQ
I
Interrupt output to the host processor
17
GND
G
Common ground
18
SPI_CLK
I
SPI interface clock
19
SPI_MOSI
O
SPI data input
20
GND
G
Common ground
11 / 12
8. Mechanical Information
8.1. Mechanical Dimension
Size Weight
42.3 x 28.0 x 9.8 mm Typ. 6g
12 / 12
8.2. Assembly
Product Label Top Case
PCB Bottom Case
13 / 12
9. User Quick Manual
9.1. Pole Zigbee Module User Manual
Pole Zigbee Module is suitable for Gen2 Gateway. 3 Slots of Gen2 Gateway can be used for Zigbee. To fulfill the ESL System, at least 3 Pole Zigbee Modules should be inserted to the Gateway.
Likewise this picture, when you inserting modules, be careful with the directions. Modules will not be able to be putted in when the inserting direction is opposite.
9. 2. LED Alarming
ATEC IoT
When Modules are working abnormally, three LEDs(Power, Status, Ethernet) would blink to alarm the unusual state. The abnormal phenomenon could happen when you forced pull out the modules or module malfunctions.
14 / 12
10. Disclaimers
-. ATEC IoT is not responsible for any damages caused by any accidents or operational environments exceeding the absolute maximum ratings.
-. Consultation with ATEC IoT is recommended for unassured environments or operations to avoid any possible malfunctions or damages of the products or risk of life or health.
-. Any unauthorized, without prior written consents from ATEC IoT, disassembly is prohibited if purposed for reverse-engineering. All defected devices must be reported to ATEC IoT and not to be disassembled or analyzed.
-. The product information can be modified and upgraded without prior notice.
a. Rule Part 15.19(a)(3): This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
b. Rule Part 15.21: The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help
15 / 12
Microsoft: Print To PDF