Schalter, Steckdosen & smarte Technik | Gira
Instruction Manual for GIRA models including: 5551 System 106 Fingerprint Module, 5551, System 106, 5551 Fingerprint Module, System 106 Fingerprint Module, Fingerprint Module, Module
1 x operating instructions. Ensure the package contents are complete and undamaged. Please see “Warranty” in the case of any defects. Device description.
General safety instructions. These instructions are an integral part of the product and must remain with the end ... Use without door communication sys-.
File Info : application/pdf, 2 Pages, 332.73KB
DocumentDocumenten Operating instructions Front view 1 System 106 fingerprint module 2 5551 ... 10867953 06/22 General safety instructions Electrical devices may only be installed and connected by a qualified electrician! These instructions are an integral part of the product and must remain with the end customer. Required accessories · System 106 surface-mounted housing, 1-gang to 5-gang (item no. 5501 ..., 5502 ..., 5503 ..., 5504 ..., 5505 ...) or System 106 flush housing, 1-gang to 5gang (item no. 5511 ..., 5512 ..., 5513 ..., 5514 ..., 5515 ...) Accessories · System 106 voice module (item no. 5563 ..) with call-button module (553. ..) or door station module (item no. 5565 9.). · Video control device (item no. 1288 00) or audio control device (item no.1278 00). · Gira home station · Power supply for door communication DC 24 V 300 mA (item no. 1296 00). Functional description The fingerprint module serves as access control based on biometric characteristics of human fingers. Up to 100 fingers can be taught in. The module can be operated as an individual device or integrated into the Gira door communication system. Scope of delivery 1 x System 106 door fingerprint module 1 x safety card 1 x operating instructions Ensure the package contents are complete and undamaged. Please see "Warranty" in the case of any defects. Device description 1 Front plate 2 Sensor Rear view 1 4 2 3 1 Turning bolt (4x) 2 Socket (2x): System cable 3 Mounting (4x): Module front 4 Screw terminal: TC bus and additional power supply Areas of application Use without door communication system If the fingerprint module is only to be used to trigger switching actions or to open doors without an accompanying speech or video connection, installation without a full door communication system is possible: Instead of a control device, the fingerprint module bus interface can be used, for example, to supply switching actuators, button interfaces or other Keyless In devices. Devices for voice or video connections cannot be connected. A DC 24 V 300 mA power supply is connected to the additional power supply (AS) terminals of the fingerprint module to supply the devices. Its voltage is then fed to the TC bus, to which the remaining devices are connected. The bus supply must be activated in the Keyless In app or directly on the device when starting-up the fingerprint module. Due to the devices' different power consumption, the devices sometimes count as multiple devices: · DCS switching actuator: 1 device · Button interface: 1 device · Additional Keyless In devices: 7 devices When selecting devices, do not exceed the maximum number of 20 devices. The maximum cable lengths from the DC 24 V additional power supply via the fingerprint module to the last device are as follows: · 100 m with 0.6 mm wire diameter · 150 m with 0.8 mm wire diameter The supplying fingerprint module can be located at any point. 1 2 34 5 ZV BUS BUS 1 Power supply DC 24 V 300 mA 2 System 106 fingerprint module, supplying the TC bus 3 System 106 fingerprint module 4 DCS switching actuators 5 Button interface The TC bus is connected to the fingerprint module bus terminals. The DC 24 V power supply is connected to the AS terminals. Only one Keyless In module may be connected to this DC 24 V power supply. The TC bus supply must be activated during start-up. After a factory reset, the TC bus supply is deactivated. Use as a stand-alone module in the door communication system The fingerprint module can be operated in the door communication system independently of door stations. 3 1 2 4 4 5 BUS ... ZV BUS 1 Control device 2 DC 24 V power supply 3 Home station 4 System 106 fingerprint module 5 DCS switching actuator The connection to the TC bus is made using the "Bus" screw terminals. An additional power supply can be connected to the "AS" screw terminals. If no additional power supply is connected, the fingerprint module reduces the maximum possible number of devices depending on the control device used as follows: · Audio control device: The fingerprint module replaces 16 audio devices. · Video control device: The fingerprint module replaces 10 audio or 4 video devices. Use in a System 106 door station The system cable can be used to connect the fingerprint module to System 106 modules and the door communication system. This way, the fingerprint module can, for example, trigger a switching action from a switching actuator. 2 ... 1 5 3 4 1 System 106 door station with fingerprint module 2 Surface-mounted video home station 7 3 Video control device 4 DCS switching actuator 5 Home station Power is supplied via the "System" connection. Do not assign screw terminals The fingerprint module screw terminals "AS" and "Bus" must not be occupied. If no additional power supply is connected, the fingerprint module reduces the maximum possible number of devices depending on the control device used as follows: · Audio control device: The fingerprint module replaces 16 audio devices. · Video control device: The fingerprint module replaces 10 audio or 4 video devices. Protecting the control device against unauthorised access In areas requiring a high level of security, the control device should be secured (locked) against unauthorized access. Mounting the module Mounting the module The following steps can be found in the mounting instruction for the System 106 surface-mounted housing 1- to 5-gang or flush-mounted housing 1- to 5-gang: · Lock the module on the mounting frame. · Connect the system cable. · Place terminating resistors · Swivel the function carrier into the surface-mounted housing and screw it in place. Operation It is only necessary to place the previously taught-in finger once on the module to operate fingerprint module. Touch with finger To ensure the fingerprint module functions properly, the finger must be correctly positioned during both the teaching in process and subsequent operation. Ideally: Place the area with the strongest fingerprint swirl (the centre of the fingertip) centrally on the sensor. False Start-up The fingerprint module can be put into operation and configured using the Gira Keyless In app or manually on the device. When starting operation, you must choose an operating mode. Subsequent changes are only possible with additional effort. Starting-up with the Gira Keyless In app 1. Download the Gira Keyless In app to the administrator's mobile device: 2. Start the app and follow the instructions on the screen. Activation code The activation code required for start-up can be found on the enclosed safety card. Starting-up without the app If you want to perform start-up manually, please refer to the instructions on the next page. Acknowledgement signals LED lights up green Tone 1 x long flashes green - lights up red 3 x short lights up - orange lights up blue - lights up red 4 x short Meaning positive acknowledgement signal, e.g.: · Input successful · Finger recognised Device is in delivery state negative acknowledgement signal, e.g.: · Finger not recognised · Input not correct Administrator mode or SysProg is active Bluetooth connection active A negative acknowledgement signal for an access attempt outside the permitted time period in the case of a time-limited access authorization Acknowledgement tone off If the acknowledgement tone is switched off, no acknowledgement tones sound. The acknowledgement signals are given solely by the LED. Technical data Power supply: via system (flat ribbon cable, 10-pole) or via control device or via AS (DC 24 V 300 mA) Power intake Stand-by mode: 650 mW Connections: 2 x system 2 x additional supply 2 x 2-wire bus Ambient temperature: -25°C to +70°C Protection type: IP54 Dimensions (W x H): 106.5 x 106.5 mm Radio frequency: 2.402 -2.480 GHz Transmission capacity: max. 2,5 mW, Class 2 Transmitting range: typ. 10 m Manual start-up Start-up is carried out using the following steps: · Teach in first administrator · Teach in user finger · Configure fingerprint module · for use in the door communication system: Assign door-opener / switching actuators Detailed start-up instructions Detailed instructions for manual start-up can be found in the Gira download section under: Basics for teaching in a finger 1. Place the finger to be taught in in the middle of the sensor until the short acknowledgement tone sounds. 2. As soon as the LED lights up orange, place the finger on the sensor again. 3. Repeat steps 1 to 2 several times. 4. The finger is taught in when a long ack- nowledgement tone sounds and the LED lights up green. For "difficult" fingers, e.g. if a person has very dry skin, it may be necessary to place the finger to be taught-in up to 7 times. If 3 short tones sound after the seventh attempt, the finger has not been successfully taught in. In this case, place the finger again (step 1) or use another finger. Commands for teaching in and deleting taught-in fingers You can mark the taught in fingers in the table on the right hand side. Function Start mode LED Touch with finger mode active Teach in first administrator Teach in user finger Admin Progr. Admin flashes green orange AdminNEW(7x) Progr.NEW(7x) UserNEW(7x) Teach in further administrators Delete administrator Admin Admin Admin Progr. Progr. Progr. orange flashes red AdminNEW(7x) Progr.NEW(7x) Admin or Progr. Delete user finger Admin Progr. Progr. flashes red Users Factory reset (delete Admin Admin all assignments) flashes red Admin(7s) Tone 2 x long 2 x long 2 x long 1 x long 1 x long 2 x long Commands for configuring the fingerprint module Function Start mode Set illumination level Progr. Admin (off, level 1, level 2) Set acknowledgement Progr. tone level (on, off) Admin LED Change setting mode active flashes orange twice Admin flashes orange twice Progr. Tone 1 x long 1 x long Commands for use without door communication system Function mode, switch Switch system programming mode on/off Switch DCS bus power supply on/off Progr. Progr. Progr. Progr. Progr. Admin LED mode switched flashes orange flashes orange Tone 1 x long 1 x long Commands for assignments in the door communication system: Assign switching actuator Function assign switching actuator (individual assignment) or Delete assignment assign switching actuator (group assignment) or Delete assignment mode start LED Assign mode active Control device System flashes progr. orange Switching actuator Progr. Users Control device System flashes progr. orange Switching actuator Progr. Admin Tone 1 x long 1 x long Commands for assignments in the door communication system: Assign door-opener Function mode start Stand-alone devices Control device (without door station): progr. Assign door-opener Control device opener progr. Assign door-opener (individual assignment) or Delete assignment Control device progr. Control device opener progr. Assign door-opener (group assignment) or Delete assignment Control device progr. Control device opener progr. System doorSystem door- System door- LED Assign mode active flashes orange Progr. Progr. Admin flashes orange Users flashes orange Admin Tone 1 x long 1 x long 1 x long Overview of administrators Administrator Admin finger Programming finger Example administrator User finger overview User / function User finger Conformity Gira Giersiepen GmbH & Co. KG hereby declares that the radio system type art. no. 5551 .. meets the directive 2014/53/EU. You can find the full article number on the device. The complete text of the EU Declaration of Conformity is available under the Internet address: www.gira.de/konformitaet Warranty The warranty is provided in accordance with the statutory requirements via the retailer. Please submit or send faulty devices postage paid and with a fault description to your sales representative (retailer / installation company / electronics retailer). This person will forward the devices to the Gira Service Centre. Gira Gira Giersiepen GmbH & Co KG Elektro-Installations-Systeme P.O. Box 1220 42461 Radevormwald, Germany Phone: +49 2195 602 - 0 Fax: +49 2195 602 - 191 info@gira.de www.gira.de