whatsgps.com
Instruction Manual for WhatsGPS models including: zTrack-18L GPS Tracker, zTrack-18L, GPS Tracker, Tracker
zTrack-18L – Zetronix
File Info : application/pdf, 16 Pages, 2.23MB
DocumentDocumentGPS Tracker Model:zTrack-18L Manual 1.Product Features Real-time Tracking GPS 4G network GPS dual communication satellite positioning OTA remote upgrade IP67 waterproof design Track Playback Strong 10000 ma rechargeable magnetic suction large battery Remote listening SOS Vibration alarm Multiple working modes SOS alarm Low electric alarm Temperature and humidity detection GEO-FENCE alarm 2.Installation Instructions 2.1.Appearance Front SOS alarm T&H MIC Back 2.2.Device online operation 2.2.1. Insert the SIM card into the GPS tracker (SIM card requires SMS, data service and phone function) (Ensure the device is powered, if not, connect the charger to power it) ON/OFF On-off key Insert the sim card SIM 2.1.2 Command send operation Please send two text messages to sim card number of GPS tracker using your mobile phone. 1) APN, apnname# This SMS is used to connect the GPS tracker to your local network. (APN's name, is the APN of your SIM card's local carrier, such as APN, cmnet# , If you don't know the APN of your sim card, check it by searching or ask your local carrier) 2) SERVER, 1, gps.whatsgps.com, 6801,0# This SMS is used to connect GPS tracker to WhatsGPS tracking platform For other platforms, please refer to this format to send commands, see the command list below for details 2.1.3 To see whether the tracker is online, go to www.whatsgps.com or download the WhatsGPS app. 2.3 Indicator light status ON/OFF LED type LED status Meaning Flash Slow flash Orange Always on Network initialization The network reception signal is normal Network/GPRS online Not bright Network signal is not received / the card is not inserted Flash GPS signal search Blue Always on Not bright GPS positioning success GPS sleeping/not working Red Always on Not bright Equipment charging No charge Ark:If the battery is completely dead, the full charge time is about 8 hours. Mild fever is normal when charging. 2.4 Installation method The installation mode of the device is hidden installation. * To avoid damage by thieves, the device location should be hidden as far as possible; * Avoid being placed with transmitting sources such as reversing radars, burglars, and other in-vehicle communication devices; * Can be fixed with cable ties, or with wide sponge strong double-sided adhesive; * The device has a built-in GSM antenna and GPS antenna. When installing, it should be sure to face up (towards the sky), and there is no metal shielding above. 2.5 Function declaration The Bluetooth configuration function needs to be used with the Bluetooth tool software. You can contact the dealer technicians to get the download address or download it through the IOS app store and the Android app store. The specific operation mode can be scanned through the QR code at the end of the manual for video viewing. The listening function requires the SOS number to use. 3.Installation diagram Deputy location Under the glove box rear windshield Under the passenger seat Back in the box In the glove compartment Under the rear seat Armrest box 4.Specifications Project Operating voltage Specification 3.8V Remark Position method GPS+LBS Positioning error <10 M Communications network 2G/4G Communication band Global version: LTE-FDD B1/B2/B3/B4/B5/B7/B8/ B12/B13/B18/B19/B20/B2 5/B26/B28/B66 LTE-TDD B34/B38/B39/B40/B41 GSM 850/900/1800/1900 MHz 2. Main Function Communication mode Range of working temperature Working humidity TCP -20~ +75 10% RH ~ 85%RH Specifications size 92mm*63mm*36mm Weight 317g 5.Description of Common Commands The following commands can be sent by SIM card SMS or WhatsGPS platform 5.1 Common setup commands SN Command function Command format SERVER,mode,domai 1 Set online nName/IP,port,0# SERVER,1,gps.whatsg ps.com,6801,0# Remark Set the device to point to server IP and port 2 Set APN APN, [APN's name]# APN, cmiot# The APN varies according to the local telecom operator 3 Set upload TIMER,[T1]# interval TIMER,10# T1: 5-18000 seconds, motion upload interval, the device defaults to 10s ; 4 Heartbeat interval setting HBT,[T]# HBT,3# T1: 60-360S, default 180s 5 Set time GMT,[A],[b],[C]# zone GMT,E,0,0# A=E/W, for the eastern and western time zones; B: 0-12, is time zone C: 0,15,30,45, which represents the half time zone and defaults to 0. Set the 6 SOS / listening number Add the SOS SOS,A,[phone1][,pho ne2][,phone3]# numbers, and you can add three SOS numbers simultaneously SOS,D,[sequence Delete the number 1][, 7 SOS / listening sequence number 2][,sequence number number 3]# SOS,[D],[phone number]# Multiple numbers can be deleted by the serial number or SOS number, and multiple numbers can be deleted simultaneously 5.2. Common query commands SN Command function Command format 1 Query parameters PARAM# Query 2 status 3 Device restart STATUS# RESET# Remark Query the currently set parameters of the device Query the current working status of the device 5.3.Common alarm commands SN Command function Command format Remark A=ON/OFF, default is OFF; M=0/1/2 1 Vibration alarm SENALMAM# Alarm mode: 0 only GPRS 1:SMS+GPRS, 2:GPRS+SMS+PHONE 2 Low electric BATALM,[A] alarm [M]# SOSALM, 3 SOS alarm [A][M]#, [A][M]# Please turn on the device power switch in advance. A=ON/OFF, the default is ON; M=0/1/2/3,Alarm mode : 0 : only GPRS, 1: SMS+GPRS, 2: GPRS+SMS+PHONE, 3:GPRS+PHONE The default alarm mode is 0. Please turn on the device power switch in advance. A=ON/OFF, the default is ON; M=0/1/2/3,Alarm mode : 0 : only GPRS, 1: SMS+GPRS, 2: GPRS+SMS+PHONE, 3:GPRS+PHONE The default alarm mode is 0 5.4.Common working mode instructions SN Command function Command format Remark Timing positioning mode: T = interval time, 10~86400 seconds; default is 600; A=GPS switch; 0=GPS off 1=GPS on; default is 0 = Timed positioning mode MODE,1,T, A,B,C# WIFI off 1 = WIFI switch; default is 1 C = LBS switch; 0 = LBS off 1 = LBS on; default is 1 motion upload location, no upload positioning without movement, GSM data often open (can receive instructions normally) 1 Intelligent positioning mode (default mode): T = interval time, 10~86400 seconds; default is 20; A=GPS switch; 0=GPS off Intelligent MODE,2,T, positioning A,B,C,D# mode 1=GPS on; default is 1 B = WIFI switch; 0 = WIFI off 1 = WIFI on; default is 1 C = LBS switch; 0 = LBS off 1 = LBS on; default is 0 D = GPRS switch; 0 = GPRS off1= GPRS is on; the default is 110s Once, motion upload, no motion do not upload, gsm often open Super power saving mode Super power saving mode: T1 = cycle interval; setting range 5-43200 MODE,3,T minutes. A=GPS switch; [,A][,B][,C] 0=GPS off 1=GPS on; # default 1 B = WIFI switch; 0 = WIFI OFF 1 = WIFI on; default 1 C = LBS switch; 0 = LBS off 1 = LBS on; default 1 Alarm clock mode: A indicates the number of alarm clocks. Alarm clock mode MODE,4,A, T1,T2,T3,T4 ...# T1, T2, T3 and T4 represent the alarm time, the number corresponds to A, up to 12 alarms can be set in the format HH: MM MODE# Query working mode 6.Troubleshooting If you feel something is wrong with your device while operating, see the following questions and solutions. If the problem still cannot be solved, please contact the seller or service provider. Common Problem Cause Solution When devices are used in areas with poor Poor signal reception reception, such as near tall buildings or basements, radio waves Use the device in a location with good signal cannot be transmitted effectively The SIM card is not installed properly Check the SIM card Dirt on the metal surface of the SIM card Wipe with a clean cloth Unable to connect to Invalid SIM card the network Out of GSM service area Contact your Internet Service Provider Please move to ISP service area Weak signal Please move to a strong signal and try again Please confirm whether Turn on the device the device is switched on battery switch Shutdown Please check whether the Please install the SIM is installed properly SIM card properly Poor contact Check that the plug is properly connected 7.After-sales warranty card User information User name Contact number Address Product model Date of purchase Name of the seller Seller's address Seller's phone number IMEI number Invoice number *This card is the basic warranty certificate, please fill it carefully and keep it properly. Warranty Description Important Note: Please keep this warranty card properly, and enjoy one-year after-sales warranty with this card. If this card is lost, your terminal warranty period will be postponed to your purchase date within 30 days after the factory date of the terminal checked by our company. Second, the scope of the warranty. 1: During the warranty period, we give free warranty if there is a problem due to the quality of the repair item itself. 2: During the warranty period, such as due to human factors, improper operation, incorrect power supply voltage caused by failure, due to the courier process dropped, damaged by their own disassembly or torn warranty strip, and natural disasters are not covered by the warranty. 3. This warranty does not apply to cases other than defects in materials, design and workmanship. 4. There is no right to extend or renew the warranty for repair or replacement under this warranty. 8.Platform tracking Installation video You can watch the installation video of the device and the tutorial video of using the APP on YouTube by scanning the QR code below FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC's RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.