Instruction Manual for MBRP models including: S5316 Cat Back Exhaust System Dual Split Side, S5316, Cat Back Exhaust System Dual Split Side, Back Exhaust System Dual Split Side, Exhaust System Dual Split Side, Dual Split Side, Split Side, Side
Cat Back Exhaust System Dual Split Side T409 Stainless Steel For 09-20 Toyota Tundra MBRP | The Race Car Factory
Figure 1 Figure 2 Figure 3 Figure 4 Removal of Stock System: 1. Apply a penetrating lubricant liberally to all exhaust fasteners, hangers and rubber insulators. 2. Remove hardware from stock extension pipes. Retain for reinstallation. Refer to Figure 1. 3. Remove exhaust from rubber insulators. Refer to Figure 2. 4. Remove the exhaust from the rearmost hanger. Leave the rubber insulators on the truck for installation. Refer to Figure 3. Installation of MBRP Performance Exhaust: 1. Install the Driver Side Front Pipe, reusing the existing hardware and attaching the hanger to the existing rubber insulator. Leave the hardware loose enough for some adjustment. Refer to Figure 4. S5316 © 12/21 PAGE 2 OF 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 S5316 © 12/21 2. Install the Passenger Side Front Pipe reusing the existing hardware. Leave the hardware loose enough for some adjustment. Refer to Figure 5. 3. Slide 2.5" Clamps over the Passenger Side Front Pipe and the Driver Side Front Pipe. Install the Mufflers onto the Driver Side Front Pipe and then the Passenger Side Front Pipe. Refer to Figure 6. 4. Slide a 2.5" Clamp over the outlet side of the driver's side Muffler. Position the Driver Side Over Axle Pipe and loosely attach it to the Muffler. Install the Driver Side Over Axle Pipe hanger into the factory rubber insulator. Refer to Figure 7. 5. Slide a 2.5" Clamp over the Driver Side Tailpipe and install onto the Driver Side Over Axle Pipe. Install the Hanger Assembly onto the Driver Side Tailpipe and install to the frame using the fastener provided. Refer to Figures 8, 9 and Detail A on Page 1. 6. Slide a 2.5" Clamp over the outlet of the passenger side Muffler. Position the Passenger Side Over Axle Pipe over the axle and loosely attach it to the Muffler. Loosely attach to the Driver Side Over Axle Pipe using the hardware provided. Refer to Figure 10. Note: Additional 5/16" Flat Washers are provided in case spacing is required for adjustments. PAGE 3 OF 4 Figure 10 Figure 11 7. Slide the Passenger Side Tail Pipe onto the Passenger Side Over Axle Pipe installing the hanger to the existing rubber insulator. Refer to Figure 11. 8. Install and adjust the Exhaust Tips to suit. Tighten the lock bolt located on each Exhaust Tip. 9. Carefully align the system and tips. Align the edge of each band clamp with the edge of the joint it is connecting. Tighten all hardware and clamps, starting at the front and working rearward to secure the system. Check along the full length of the exhaust system to ensure there is adequate clearance for fuel lines, vent lines, brake lines, frame, bodywork, suspension and any wiring, etc. If there is any interference detected, relocate or adjust to provide adequate clearance. Ensure all clamp connections are secure and components are unable to rotate or slide. Band clamps require approximately 45 lb-ft (60 N-m) of torque. Verify clearances, system security and band clamp torque after 30-60 miles (50-100 km) of driving. Congratulations! You are ready to begin enjoying the improved performance and driving experience of your MBRP Performance Exhaust system. We hope you enjoy your purchase! S5316 © 12/21 PAGE 4 OF 4Microsoft Word for Microsoft 365