WallarGe 5.8 GHz Wireless TV Headphones User Manual
Model: HP003, FCC ID: 2AYZG-HP003
Thank you for your purchase of this quality 5.8 GHz Wireless Over Ear Headphones. Please read these instructions carefully and store in a safe place for future reference.
Email: WallarGe@outlook.com
Introduction
This headphone adopts the internationally advanced 5.8 GHz wireless audio transmission technology, which is characterized by stable signal (high-frequency frequency hopping anti-interference technology, easy to avoid the interference of other signals), long transmission distance (within a radius of 30 meters) and features such as stereo high-fidelity sound quality. As long as you connect the dock to any audio device you want to listen to, such as TV, PC, MP3, DVD, VCR, Hi-Fi system, radio, etc., you can use the headphone to listen to the sound of the audio device either indoors or outdoors.
Overview of the Headphones
There are four buttons, two indicators, and a charging contact pole on the left ear of the headphone. The four buttons are: power on/off button, mute button ☑, volume up button +, and volume down button -. The red light is the power indicator, and the green light is the audio signal indicator.
- Adjustable headband
- Volume up control button
- Volume down control button
- Mute button
- Headphone power indicator (Red light)
- Headphone audio signal indicator (Green light)
- Charging contact pole
Overview of the Docking Station
The docking station is not only a 5.8 GHz RF transmitter but also a charging station. It has three indicators on the front: POWER indicator, SIGNAL indicator, and CHARGE indicator. The headphone and dock are pre-paired. If you need to pair more headphones, follow the manual pairing steps.
- Docking Station
- Charging column
- DC IN: Power adapter jack
- AUDIO IN L: Left channel audio line jack
- AUDIO IN R: Right channel audio line jack
- PAIRING Key: Used to pair more headphones
- Power indicator (Red light)
- Signal indicator (Green light)
- Charge indicator (Red light for charging, Blue light for fully charged)
Pairing Steps: Press and hold the pairing key on the dock until its signal indicator flashes. Then, press the power button ▶ on the headphones until the green indicator flashes. Release the power button and wait for the headphones to automatically pair with the base. The green indicator on the headphones will remain solid when pairing is successful.
Supplied Accessories
- Wireless Headphones
- Docking Station (5.8 GHz wireless transmitter)
- AC Power Adapter
- User Manual
- Thank-you Letter
- A: AV to AV audio cable
- B: AV to 3.5mm audio cable
Note on Audio Cable Choice:
- Using cable A to connect the TV and docking station allows sound to be heard by both headphone users and others watching TV without headphones. The TV and headphone sounds are independent.
- Using cable B to connect the TV and docking station allows only the headphone user to hear the sound. The TV will have no external sound.
Technical Parameters
- Working voltage (docking station): DC 5V-500mA
- Lithium battery capacity: 1100 mAh
- Frequency response: 20Hz-20KHz
- Carrier frequency: 5.8GHz
- Frequency modulation: GFSK
- Distortion degree: < 0.5%
- Signal to noise ratio: > 70 dB
- Range of launch: 30 meters (100 feet)
- Endurance: 20 hours
- Charging time: 3-5 hours
Operation Steps
- Connect the AC power adapter to the docking station. The power indicator will turn red.
- Charge your headphones for at least 3 hours. The charging indicator will be red while charging and turn blue when fully charged.
- Check the audio output jack of your audio device and select the desired audio cable. Connect the audio cable to the audio source device and the docking station. Ensure correct connections for red and white audio jacks.
- Check if the audio signal indicator of the docking station turns green. This indicates that the docking station has detected an audio signal input. If no signal is detected within 3 minutes, it enters sleep mode.
- Adjust the headband for comfort.
- Turn on the wireless headphones. Press and hold the power button for 2 seconds until the red power indicator lights up. Wait for the green signal indicator to light up, confirming connection to the docking station.
- Put on your headphones and adjust the volume to the optimal level. Ensure the distance between the headphones and docking station does not exceed 30 meters (100 feet).
Applicable to many audio devices: TV, PC, Smart Phone, MP3, CD Player.
Important Charging Tips
- Charge headphones for at least 3 hours before first use for optimal battery performance.
- Charging indicator is red during charging; turns blue when fully charged (approx. 4 hours).
- Ensure good contact between headphone charging contacts and the docking station's charging column for proper charging. Magnets assist in alignment.
- A full charge provides approximately 20 hours of continuous use, depending on volume and distance.
Important Safety Instructions
General Information
- Do not disassemble the product.
- Keep the product away from water and moisture.
- Avoid exposure to excessive heat or direct sunlight.
- Do not place naked flame sources on the apparatus.
- Clean with a dry cloth; avoid abrasive or alcohol-based cleaners.
- Do not operate or store in temperatures below 0°C (32°F) or above 40°C (104°F).
- The AC/DC adapter's mains plug is the disconnect device and should remain accessible.
- Protect the power cord from damage.
- Unplug during lightning storms or when unused for extended periods.
- Refer servicing to qualified personnel if the apparatus is damaged.
Hearing Safety
- Limit listening time at high volumes to avoid hearing damage. Set volume to a safe level.
- Avoid continuously increasing volume as hearing adapts.
- Use caution or discontinue use in potentially hazardous situations.
- Excessive sound pressure can cause hearing loss.
- Using headphones while driving is not recommended and may be illegal.
- Avoid distractions from music or phone calls in traffic or dangerous environments.
Troubleshooting
| Problem | Solution |
|---|---|
| Headphone can't be turned on | Ensure the headphone is charged and not low on power. |
| Headphone can't be charged (charging indicator isn't lit) | Ensure the headphone's charging contact makes good contact with the docking station's charging column. You may need to adjust the position for the charging indicator to turn red. |
| Headphones have no sound, or sound on only one side | 1. Verify all adapter and audio cables are connected correctly. 2. Ensure the audio source is not muted and its volume is at least 50%. 3. Ensure the headphone is not muted and its volume is at least 50%. 4. Confirm the headphone and docking station have detected audio signals (signal indicator is green). 5. Try a new audio cable if the current one might be broken. |
| Interrupted sound | 1. Ensure all audio cables are connected correctly. 2. Reduce the distance between the headphone and docking station. 3. Turn off other devices (smartphones, routers) that might cause interference. |
| Sound coming from the audio source | 1. Turn off the internal speakers of the audio source. 2. Contact the audio source manufacturer for support. |
| Headphone shuts off automatically | 1. Check if the signal is received normally and the signal light is on. 2. Reduce the distance between the headphone and docking station. 3. Charge the headphone if the battery is dead. |
| No communication between headphone and docking station | 1. Ensure the AC adapter is connected to the docking station. 2. Ensure the headphone is charged. 3. Ensure the distance between the headphone and docking station is within 30 meters (98.2 feet). |
| Headphone or docking station damaged | Contact WallarGe for a replacement or refund. |
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If this equipment causes harmful interference to radio or television reception, the user is encouraged to try to correct the interference by reorienting or relocating the receiving antenna, increasing the separation between the equipment and receiver, connecting the equipment into an outlet on a circuit different from that to which the receiver is connected, or consulting the dealer or an experienced radio/TV technician.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits for an uncontrolled environment. It should be installed and operated with a minimum distance of 20cm between the radiator and your body.
Hassle Free Service
1. Product does not meet your needs? Contact WallarGe for assistance with refunds.
2. Received defective/damaged product? Email WallarGe with your order ID for a replacement within 24 hours.
3. Unable to operate the product? Contact WallarGe's 24-hour standby service team for assistance.
Our Warranty:
- 90-day money back guarantee
- 365-day free replacement
- 24-hour standby service team
Email: WallarGe@outlook.com
File Info : application/pdf, 2 Pages, 3.85MB
DocumentDocument