Electromechanical Trim Tab Systems | Lectrotab
Instruction Manual for LECTROTAB models including: JLC-11, JLC-11 Joystick LED Trim Tab Control, Joystick LED Trim Tab Control, LED Trim Tab Control, Trim Tab Control, Tab Control, Control
Lectrotab Joystick LED Trim Tab Control - Consumer Marine Supply
Lectrotab Joystick LED Trim Tab Control
File Info : application/pdf, 2 Pages, 384.98KB
DocumentDocumentJLC-11 Joystick LED Trim Tab Control Lectrotab's Joystick LED control incorporates features requested by boat owners to provide a user-friendly control for a more enjoyable boating experience. · Single "Joystick" control · NMEA 2000 compatible · LED display of each trim tab position FEATURES · Microprocessor based trim tab control with LED tab position indicators · NMEA 2000 compatible with JLC-NMEA adapter · Move both tabs up or down simultaneously with a single motion · Dual station ready just add a second JLC-11 and JR-* cable (sold separately) · Automatic return to last tab position if ignition key is turned off and back on again · Completely sealed, completely waterproof and will not deteriorate in sunlight · Automatic tab retraction and calibration with key or accessory switch off · Easy upgrade from any of our Lectrotab controls · No external power module required · LED tab position indicators dim automatically in darkness and brighten in sunlight · Single or Dual Actuator per tab · Operates on 12 or 24 volt dc systems PRELIMINARY SPECIFICATIONS Model Display Number of Overall Number Color Stations/Actuators Width Overall Height/ Thickness Mounting Hole DC Cutout (Diameter) Voltage Fuse Size Power Input (1 Actuator per Tab) JLC-11 Black Single or Dual Station/ 1 or 2 Actuator/tab 3.0"/ 77mm 3.0"(77mm)/ 2.0"(50mm) 2.625"/66.7mm 12/24 12vdc = 15 or 20 amps 24vdc = 10amps Linear Devices Corporation 11126 Air Park Road, Suite G, Ashland, VA 23005 www.lectrotab.com, Ph 804-368-8428, Email: sales@lectrotab.com August 2023 Fuse Size Aux.(MUST CONNECT) 1 to 2 amp JLC-11 WIRING and DIMENSIONS JLC-11 Programming Chart Function Timing Remember Last Tab Position Swap LED's Program Mode Sequence Enter Adjust Setting Exit Push & hold joystick left Move and hold Joystick Up or Down Push joystick right and hold 4 seconds + Range 4 - 12sec Pull & hold joystick back Move and hold Joystick Up or Down Push joystick right and hold 4 seconds + Standard/Remember Push & hold joystick right Move and hold Push joystick right Joystick Up or Down and hold 4 seconds + LEDs match tab movement or opposite tab movement Disable Auto Tab Retract Push & hold joystick forward Move and hold Push joystick right Joystick Up or Down and hold 4 seconds + Enable/Disable Independent Tab Control Push & hold joystick 45° towards upper left position (between top and left position) Move and hold Joystick Up or Down Push joystick right and hold 4 seconds + Enable/Disable Default 8sec Standard LEDs match tab movement direction Enabled Disabled Program Details 8 LEDs = 8 second actuator 4 LEDs = 4 second actuator 8 LEDs each side = Standard Retract 1 LED each side = Remember Last Tab Position 1 LED on right and left = LEDs follow and match tab movement direction 8 LEDs on right and left = LED follow opposite of tab movement direction #1 LED each side = Default of Auto Tab Retract enabled #8 LED each side = Auto Retract Disabled #1 LED each side = Default Disabled or tabs do not operate independently #8 LED each side = Tabs operate independently Programming Details: Timing: #LEDs lit corresponds to the #seconds in actuator stroke time i.e. 8 LEDs = 8 seconds, 4 LEDs = 4 seconds (Actuator's A and B series = 8 seconds, C and D series = 4 seconds and S series = 6 seconds) Rember Last Tab Position: If AUX power is switched from +12 or 24vdc to 0vdc, tabs retract (Set Timing + 1 sec.). When power is reapplied, tabs go to last position before key sw. off. Removing +12 or 24vdc power source will reset original setting back to fully retracted and keep fully retracted at new power sorce on. (8 LEDs on each side = standard auto retract and no last setting, 1 top LED on each side = remember last tab position before Aux power off.) Swap LED's: 1 LED on right and left side = LEDs follow and match tab direction, 8 LEDs on right and left side = LEDs follow opposite of tab direction Disable Auto Tab Retract: *Note* this program mode does not require +12vdc to the AUX terminal. Press the All Up and All Down buttons at same time for 2sec Press the STBD Bow Down/Up to adjust between Enable and Disable. (#1 LED each side = Default of Auto Tab Retract enabled. #8 LED each side = Auto Retract Disabled) Press the Port Bow Up to exit program and save setting. Independent Tab Control: 1 LED on right and left side = Tabs do not operate independently, 8 LEDs on right and left side = Independent control of each tab Linear Devices Corporation 11126 Air Park Road, Suite G, Ashland, VA 23005 www.lectrotab.com, Ph 804-368-8428, Email: sales@lectrotab.com August 2023