User Guide for WONDOM models including: ADAU1701, Digital Signal Processor Kernel Board
Power of APM2: The DSP Kernel Board (APM2) could be powered by: 1) 5V micro USB through micro USB charging port (J2). 2) External 5-12V DC Supply through ...
Overview. WONDOM ICP1 is an in-circuit programmer for customer programming of WONDOM products. On-board self-boot EEPROM is included in ICP1 for operating the board independently of...
WONDOM ICP1 User Guide IN-CIRCUIT PROGRAMMER FOR ADAU1701 DIGITAL SIGNAL - ICP1 By Sure Electronics Co., Ltd. Overview WONDOM ICP1 is an in-circuit programmer for customer programming of WONDOM products. On-board self-boot EEPROM is included in ICP1 for operating the board independently of the Analog Devices, Inc., SigmaStudioTM software. The package includes: IN-CIRCUIT PROGRAMMER FOR ADAU1701 DIGITAL SIGNAL - ICP1 x 1 6-pin cable x 1 Functions Programming Required Tools Analog Devices, Inc., SigmaStudioTM Applicable Products JAB3 APM2 Product List Model SKU Description ICP1 ICP3 ICP5 APM2 APM3 JAB3-1100 JAB3-160 JAB3-250 JAB3-230 DB-DP11219 DB-DP11224 DB-DP11226 AA-AP23122 AA-AA11428 AA-JA31181 AA-JA31211 AA-JA32172 AA-JA32473 In-circuit Programmer for ADAU1701 Digital Signal WONDOM In-circuit Programmer with BLE Bluetooth for APP control In-circuit Programmer with UART for PC UI Control & BLE for APP Control ADAU1701 Audio Digital Signal Processor Kernel Board ADAU1701 Audio Digital Signal Processor Interface Extension Kit 1x 100 Watt Class D Audio Amplifier Board with Audio DSP - JAB3-1100 1 x 60 Watt Class D Audio Amplifier Board with Audio DSP - JAB3-160 2 x 50 Watt Class D Audio Amplifier Board with Audio DSP - JAB3-250 2 x 30 Watt Class D Audio Amplifier Board with Audio DSP - JAB3-230 Notes: - Represents no basic cable Basic Cables Included 6Pin cable x 1 6Pin cable x 1 6Pin cable x 1 10Pin cable x 1 Power cable x 1 Speaker cable x 1 3.5mm AUX IN cable x 1 Interface Definition In this document, we will mainly give instructions on the following applications: 1) How to achieve programming of APM2 / JAB3 with WONDOM ICP1 2) How to realize APP control of APM2 / JAB3 with WONDOM ICP1 KEY1 Reset SW When programming, please make sure SW at (PROGRAM) Micro USB Port 1) DC5V power supply 2) Communication with computer Programming Port For connection with applicable products with a 6-pin cable Open Source Files for PROGRAMMING Products Function File Version Download APM2 Demonstration of Signal Flow Chart APM2_SigmaStudio.dspproj - Download JAB3 - Mono Demonstration of Signal Flow Chart JAB3_SigmaStudio_MONO.dspproj - Download JAB3 - Stereo Demonstration of Signal Flow Chart JAB3_SigmaStudio_STEREO.dspproj - Download Note: All the "Demonstration of Signal Flow Chart" files are just for signal flow chart demonstration and customers can not use them as running programming. How to achieve programming of APM2/JAB3 with WONDOM ICP1? ICP1 IN-CIRCUIT PROGRAMMER FOR ADAU1701 DIGITAL SIGNAL - ICP1 Checklist Before starting, please make sure you have the following items on hand. 1 WONDOM APM2+Extension Kit (APM3)/JAB3 3 Analog Devices, Inc. SigmaStudioTM + OR 2 WONDOM ICP1 with a 6-pin cable 4 Accessories Speakers Cables Phone ... Quick Start To quickly get started with the programming of WONDOM APM2 or JAB3 via ICP1, do the following steps: 1) Install the SigmaStuido software 2) Connect ICP1 to computer 3) Connect audio cables of APM2/JAB3 4) Power up the audio system 5) Connect ICP1 with APM2/JAB3 6) Program Click HERE to watch video. Since the most steps of programming APM2 and JAB3 are the same, we will take APM2 as an example to show you how to operate. If there is difference or points to note, we wil mark out with red words. How to program Be sure to follow these connection steps. SETTING UP THE ICP1 POWERING UP THE BOARD CONNECTING ICP1 WITH APM2 / JAB3 1 2 3 4 5 INSTALLING SIGMASTUDIO SOFTWARE CONNECTING THE AUDIO CABLES PROGRAMMING Installing Sigmastudio software Download the installation package for SigmaStudio software in the Analog.com. Download address is as follows. Click the EXE file and finish installation according to the prompts. https://www.analog.com/en/design-center/evaluation-hardware-andsoftware/software/ss_sigst_02.html#software-overview Setting up the hardware 1. Compile the needed program in advance. 2. Set the SW of ICP1 at (PROGRAM)* and connect the ICP1 to the computer with a USB cable. Do not connect ICP1 with target products (APM2/JAB3) now. 3. Select "USBi" from the list on the left and drag it to the blank area on the right. Repeat the action to move "ADAU1701" and "E2Prom" to the right. 4. Please note whether the ICP1 can be recognized by the computer, if the underpainting of the "USB" turn green, it represents the ICP1 is recognized, otherwise it will ture orrange and you should reconnect the ICP1 until it turn green. See figure 1. Figure 1 SW SW Setting PROGRAM Connecting Audio Cables 01. Connection This interface extension kit (APM3) provides three methods of audio input: RCA 3.5mm Aux PH-4PIN-2MM 03. RCA 3.5mm PH-4PINHeadphone 2MM Output Use the 10 pin to 10 pin cornoid to connect APM2 with interface extension kit (APM3) for playing music. 02. RCA 3.5mm Aux PH-4PIN2MM Input This interface extension kit (APM3) provides three channels of audio output: RCA 3.5mm Headphone PH-4PIN-2MM Powering up the board Make sure the SW1 of APM2 is set at (RUN). (Skip this step when programming JAB3) Power up the APM2. 1. Power of APM2: The DSP Kernel Board (APM2) could be powered by: 1) 5V micro USB through micro USB charging port (J2) 2) External 5-12V DC Supply through Vin control port (J3/J4) 3) External 3.3V DC Supply through +3.3V control port (J3/J4) 2. Power of Extension Kit: The Extension Kit (APM3) is powered by the Kernel Board (APM2) 3. Power of IC Programmer: WONDOM IC Programmer could be powered by: 1) 5V micro USB through micro USB charging port (J1) 2) External 5V DC Supply from DSP Kernel Board (APM2) Input audio signal to JAB3 and make sure the two LEDs on JAB3 are on before connecting ICP1 with JAB3. Skip this step when programming APM2. Connect ICP1 with APM3 through 6-pin cable. Programming 1.Click the "Link Compile Connect" (see figure 2) and you will find "Ready: Compiled" in the lower right corner of your computer. 2.Click the "Link Compile Download" (see figure 3) and you will find "Active: Compiled" in the lower right corner of your computer. Figure 2 Figure 3 3. Make sure the SW of ICP1 is at (PROGRAM) and the SW1 of APM2 is at (RUN), and right-click the "ADAU1701" and select "Write Latest Compilation to E2PBOM" to download the program (see figure 4), then you will see a window, choose the "I2C" on the right and click "OK" (see figure 5). Figure 5 Figure 4 Original Firmware Restore 1. Right click the "E2Prom" (see Figure 6) and click `Read/Write Window'. You will see the following interface (Figure 7). Figure 6 Figure 7 2. Click `Click here to browse for file' and select firmware file (Figure 8). Then click `Display File' like Figure 9. Figure 8 Figure 9 Original Firmware Restore 3. Click `Write Display to E2prom' then click `OK' of the prompt box (Figure 10). Figure 10 TROUBLE SHOOTING TROUBLE ICP1 cannot be recognized by PC Cannot writing the program into APM2 successfully Cannot writing the program into JAB3 successfully HOW TO SOLVE Make sure the Micro USB cable is of good quality and supports data communication Make sure ICP1 is not connected to controlled device (APM2) when connected to PC Make sure the ICP1 be recognized by PC Make sure the SW of ICP1 is at (PROGRAM) and the SW1 on APM2 is set at (RUN) Make sure JAB3 is given audio signal and the two LEDs are on Make sure the ICP1 be recognized by PC APM2 / JAB3 cannot work normally (cannot play music) under powering condition when connected with ICP1 Make sure the SW of ICP1 is at (PROGRAM) Make sure the connection steps are correct and check the input/output cables Disconnect with ICP1 and re-power APM2 Make sure the SW1 on APM2 is set at (RUN) (Not applicable to JAB3)Microsoft PowerPoint 适用于 Microsoft 365