Safety
The Whyte Series A Distribution Amplifiers are intended for indoor use only.
Do not install the Distribution Amplifier in damp, humid, hot, or dusty areas. Switch off the source of power when making connections to the Distribution Amplifier to avoid damaging the unit.
Always earth bond the Distribution Amplifier using the Earth Bonding Lug to a suitable Earth Bonding point using up to 6mm² core earth cable.
Precautions
To ensure trouble-free operation of your Whyte Distribution Amplifier:
Do not remove the cover of the Distribution Amplifier or disassemble it, as this will invalidate your guarantee.
The female F-Type connectors on this unit were designed for use with '100' type coaxial cable with a centre core diameter of 1mm². When using larger diameter '125' or '165' coaxial cables, you must ensure that suitable F connectors with reducing pins are used, otherwise damage to the unit will occur which will invalidate the guarantee.
Do not over-tighten the F connectors (finger tight only).
Guarantee
All Whyte products are guaranteed for a period of 4 years from the date of purchase against defects. Within this period, Whyte Technologies will repair or replace the faulty product. In the unlikely event, please return any faulty products to your dealer.
The guarantee will be deemed void if the serial number on the product is removed, damaged or illegible. The guarantee excludes defects caused by incorrect use, accidental damage, disassembly, water/fire/lightening damage or lack of ventilation.
General Description
A comprehensive range of RED compliant, professional Advanced Distribution Amplifiers with IRS Loop-through.
This enables Whyte Series A Distribution Amplifiers to be connected directly to a Multiswitch subscriber output whereby the SAT and TERR/RADIO signals are passed through the Distribution Amplifier before terminating at the outlet plate. The TERR/RADIO signals are amplified before being distributed to the TERR & RADIO outlets.
The Whyte Series A Distribution Amplifiers are available in sizes ranging from 2-Way to 16-Way. The IRS Loop-through can also be used to cascade multiple units to create large scale Master Antenna TV systems (MATV).
When used as a standard TERR and RADIO Distribution Amplifier, the Whyte range of Distribution Amplifiers offer a professional, low noise, high gain solution.
Features include:
- RED Compliant
- Ultra-Low Noise ≤4dB
- 10dB ~ 12dB Gain (depending on model)
- Gain Control
- IRS Loop-Through
- Cascadable
- LTE Filter (4G)
- High Quality Distribution Amplifier with a 4-year guarantee
- Internal power supply
- Remote Powering via all outputs
- Adequate cable clearance for routing underneath
- Models available include 2, 4, 6, 8, 12 and 16-way output
Product Description
The Whyte Series A Advanced Distribution Amplifier unit (model ADA108 shown for illustrative purposes) features several key components and connections:
- 1. AC In Power Cord: Connection for mains power.
- 2. Transformer Housing: Enclosure for internal transformer.
- 3. Subscriber Outputs: Multiple F-type connectors for distributing signals to outlets.
- 4. TERR / IRS Input: Input for terrestrial and satellite signals.
- 5. Gain Control: Adjustment for signal amplification level.
- 6. IRS Loop Output: Output for passing IRS signals to other devices or units.
- 7. Earth Lug: Terminal for connecting an earth bonding cable.
- 8. LED Power Indicator: Visual indicator for power status.
- 9. Corner Brackets: Mounting points for securing the unit.
- 10. UK Mains Plug: Standard UK power plug attached to the AC power cord.
Technical Description
The Whyte Series A Advanced Distribution Amplifier is engineered to meet the demands of modern Integrated TV & Satellite Reception Systems.
It features an IRS Loop-through, allowing direct connection to Multiswitch subscriber outputs. This loop-through is passive, handling frequencies from 87MHz to 2340MHz, and supports 22kHz tone and DiSEqC commands, ensuring compatibility with both legacy and dSCR Multiswitches.
When used for Terrestrial TV and Radio Distribution (MATV), the ADA offers low noise, high gain performance, and reliability. It includes a high rejection 4G Filter and a 15dB Gain Control, making it adaptable to various signal level scenarios.
The unit can be powered via the supplied AC mains lead or remotely via any of the TERR Outputs using a suitable PSU (not included).
Installation Instructions
Mounting the Distribution Amplifier
Select a suitable indoor location, avoiding damp, humid, hot, or dusty areas. Secure the amplifier using the screw slots on the corner brackets and transformer housing, employing supplied fixing screws or other suitable fixings for the wall, surface, or cabinet.
Earth Bonding
Connect the Distribution Amplifier to a suitable Earth Bonding point using the Earth Bonding Lug and a minimum 6mm² Earth Bonding Cable. Ensure the cable is directly connected to the building's PME (Protective Multiple Earthing) point.
Using the Internal AC Power Supply
If a 230V UK AC socket outlet is available, plug in the unit using the provided AC cord with a 3A fused BS1363 moulded UK mains plug.
DC Powering Options
The distribution amplifier can be powered using a 12V DC 100mA PSU. This can be connected via any of the TERR outputs for remote powering, as illustrated in the diagram.
Example Configurations
Single SAT + MATV (AC Power)
Apt TERR Distribution via IRS (AC Power)
Cascading MATV System
MATV (AC Power)
MATV (DC Remote Power)
Specifications
ADA102 | ADA104
| MODEL | ADA102 | ADA104 |
|---|---|---|
| TERR Frequency Range | 87MHz ~ 782MHz | 87MHz ~ 782MHz |
| TERR/IRS Input (F-Type Female) | 1 | 1 |
| TERR Tap Outputs (F-Type Female) | 2 | 4 |
| SAT Loop Through (F-Type Female) | 1 x 87~2350MHz | 1 x 87~2350MHz |
| RED Compliance | Class 3 | Class 3 |
| TERR Gain | 12dB | 10dB |
| Max Output TERR (IMA3 -60dB) | 90dBuV | 90dBuV |
| Max Noise Figure | <4dB | <4dB |
| SAT Through Loss | 4dB | 4dB |
| Impedence | 75 Ω | 75 Ω |
| Loop Through Passing | 13/18V / 22kHz / DiSEqC | 13/18V / 22kHz / DiSEqC |
| Mains Operation | 230V AC | 230V AC |
| Remote DC Powering (via TERR outputs) | 12V DC | 12V DC |
| Remote DC Consumption | 40mA Max | 40mA Max |
| Power Indicator | LED | LED |
| Earth Lug | Up to 6mm² core | Up to 6mm² core |
| Dimensions W x L x H (mm) | 168x116x43 | 168x116x43 |
| Weight | 332g | 340g |
ADA106 | ADA108 | ADA112 | ADA116
| MODEL | ADA106 | ADA108 | ADA112 | ADA116 |
|---|---|---|---|---|
| TERR Frequency Range | 87MHz ~ 782MHz | 87MHz ~ 782MHz | 87MHz ~ 782MHz | 87MHz ~ 782MHz |
| TERR/IRS Input (F-Type Female) | 1 | 1 | 1 | 1 |
| TERR Tap Outputs (F-Type Female) | 6 | 8 | 12 | 16 |
| SAT Loop Through (F-Type Female) | 1 x 87~2350MHz | 1 x 87~2350MHz | 1 x 87~2350MHz | 1 x 87~2350MHz |
| RED Compliance | Class 3 | Class 3 | Class 3 | Class 3 |
| TERR Gain | 10dB | 12dB | 10dB | 10dB |
| Max Output TERR (IMA3 -60dB) | 90dBuV | 90dBuV | 90dBuV | 90dBuV |
| Max Noise Figure | <4dB | <4dB | <4dB | <4dB |
| SAT Through Loss | 4dB | 4dB | 4dB | 4dB |
| Impedence | 75 Ω | 75 Ω | 75 Ω | 75 Ω |
| Loop Through Passing | 13/18V / 22kHz / DiSEqC | 13/18V / 22kHz / DiSEqC | 13/18V / 22kHz / DiSEqC | 13/18V / 22kHz / DiSEqC |
| Mains Operation | 230V AC | 230V AC | 230V AC | 230V AC |
| Remote DC Powering (via TERR outputs) | 12V DC | 12V DC | 12V DC | 12V DC |
| Remote DC Consumption | 100mA Max | 100mA Max | 100mA Max | 100mA Max |
| Power Indicator | LED | LED | LED | LED |
| Earth Lug | Up to 6mm² core | Up to 6mm² core | Up to 6mm² core | Up to 6mm² core |
| Dimensions W x L x H (mm) | 200x116x43 | 200x116x43 | 200x116x43 | 232x116x43 |
| Weight | 450g | 458g | 472g | 528g |
The EU Declaration of Conformity can be viewed at www.whytetechnologies.com.
Whyte Technologies – Digital innovation made easy