[PDF] Assembly and Operating Instructions - Sport-Tiedjeresources.sport-tiedje.com ⺠taurus
Assembly and Operating Instructions
Manual Taurus WS5 Assembly and Operating Instructions
2 persons
TFWS5.01.01
TF-WS5
Weight station WS5
2
84
Dear Customer, Thank you for deciding for a high-quality training equipment of the brand Taurus, the brand that makes athlete`s hearts beat faster. Taurus offers a wide range of home fitness equipment like elliptical cross trainers, ergometers, treadmills and rowing machines. Taurus equipment is the optimal equipment for all those who want to train at home independent of goals and fitness level. For further information please visit www.sport-tiedje.com or www.taurus-fitness.de.
SAFETY NOTICE Please read all of the instructions carefully before assembly and first use. These instructions are intended to ensure speedy assembly and explain safe usage. Make sure that all people exercising with the equipment (in particular children and persons with limited physical, sensory, mental or motor capabilities) are informed about these instructions and its content in advance. In case of doubt, a responsible person must supervise the use of the equipment. This equipment has been manufactured according to the latest safety knowledge. As far as possible, potential safety hazards which could cause injury have been eliminated. Make sure to follow the instructions carefully and that all parts are securely in place. If required, read through the instructions again to correct any mistakes. Please pay close attention to the safety and maintenance instructions given here. The contract partner cannot be held liable for damage to health, accidents or damage to the equipment when it is not used in accordance with these instructions. The equipment is only suitable for use at home. The equipment is not suitable for semi-professional (e. g., hospitals, clubs, hotels, schools, etc.) and commercial or professional use (e. g., health clubs). Retain these instructions in a safe place for future reference, maintenance or when ordering replacement parts.
3
INHALTSVERZEICHNIS
1 GENERAL INFORMATION
5
1.1 Technical Data
5
1.2 Personal safety
6
1.3 Set-up place
7
2 ASSEMBLY INSTRUCTIONS, MAINTENANCE AND CARE
8
2.1 General instructions
8
2.2 Faults and Troubleshooting
9
2.3 Maintenance and service calendar
9
3 ASSEMBLY
10
4 WARRANTY INFORMATION
40
5 DISPOSAL
42
6 ORDERING ACCESSORIES
42
7 ORDERING SPARE PARTS
43
7.1 Service hotline
43
7.2 Serial number and model name
43
7.3 Parts list
44
7.4 Exploded drawing
47
4
84
1 GENERAL INFORMATION 1.1 Technical data
Weight and dimensions: Item weight (gross, incl. packaging): 139 kg Item weight (net, without packaging): 134 kg Weight stack in kg: 90 kg Packed dimensions boxes (length x width x height): No. 1 ca. 189 cm x 57 cm x 27 cm No. 2 ca. 128 cm x 102 cm x 22 cm Set-up dimensions (length x width x height): approx. 225,1 cm x 138 cm x 211,5 cm
5
1.2 Personal safety
+ Before you start using the equipment, you should consult your physician that this type of exercise is suitable for you from a health perspective. Particularly affected are persons who: have a hereditary disposition to high blood pressure or heart disease, are over the age of 45, smoke, have high cholesterol values, are overweight and/or have not exercised regularly in the past year.
+ Please note that working out excessively can seriously damage your health. + The equipment may only be used for its intended purpose; this means for strength
training for adults. + Any other usage is prohibited and potentially dangerous. The contract partner cannot be held
liable for damage resulting from improper use. + The equipment may not be used by several persons at the same time. + Children should not be allowed unsupervised access to the equipment. + Before starting your training, make yourself familiar with all of the equipment`s functions and
setting options. Have an expert explain the correct usage of the product to you. + Make sure that nobody is in the range of motion of the equipment while exercising. + Keep your hands, feet and other body parts, hair, clothing, jewelry and other objects well clear of
moving parts. + During use, wear suitable sports clothing rather than loose or baggy clothing. When selecting
sports shoes, think about the suitability of the sole preferably this should be made of rubber or other non-slip materials. Shoes with heels, leather soles, studs or spikes are not suitable. Never work out in bare feet. + It is also important to take note of the information given in the workout instructions for creating a workout plan. + At the first signs of weakness, nausea, dizziness, pain, difficulty in breathing or other abnormal symptoms, stop your workout immediately and, if necessary, consult your physician. + Before each training session, check all cables for any possible damage. Immediately replace defective cables and do not use the equipment until it has been repaired. Also pay attention to any material fatigue. + Never let go of the handlebars or grips as long as there is resistance in order to avoid crushing and similar injuries. + Make sure that the cables are always in the wheel guide. If the cables are stuck while you are training, stop training immediately and check the cable run. + If you adjust the seat, make sure that it fully locks in its new position, because otherwise it may
slide and lead to injuries.
6
84
1.3 Set-up place
+ The equipment should only be used indoors, in a sufficiently heated and dry area (ambient temperature between 10°C and 35°C). The equipment should not be used outdoors or in rooms with high humidity (over 70%) like swimming pools. The equipment should only be stored in surroundings with an ambient temperature between 5°C and 45°C.
+ The training room should be well ventilated during training and not be exposed to any draughts. + Choose a location in which to place the equipment such that there is enough free space/
clearance to the front, the rear and to the sides of the equipment (at least 1.50 m). Furthermore, the equipment should not be set up in main entrances or on escape routes. + No objects of any type should be inserted into the openings of the equipment. + The equipment should be placed on a level and solid surface, any unevenness in the floor should be leveled out. + A floor protective mat / equipment underlay can help to protect high-quality floor coverings (parquet, laminate, cork, carpets) from dents and sweat and can help to level out slight unevenness.
2 2
7
2 ASSEMBLY INSTRUCTIONS, MAINTENANCE AND CARE
2.1 General instructions
+ Please check if all parts and tools belonging to the equipment are included in the delivery and if there is any transport damage. If there are any complaints, please contact your contract partner directly.
+ Some of the nuts and bolts to be used in assembly are already pre-mounted in order to make set-up as easy as possible.
+ The equipment must be assembled by adults. In case of doubt, ask for assistance from another person with technical skills.
+ Keep children away from the equipment during assembly, because small parts are included in the delivery and may be swallowed.
+ Make sure that you have enough space (at least 1.50 m) in every direction during assembly. + Do not leave any tools and packaging materials like plastic sheeting laying around to avoid
danger of suffocation for children. + Assemble the equipment on an underlay mat or on the cardboard packaging in order to avoid
damage to the equipment and to the floor (scratches). + Before starting assembly, all individual parts should be placed on the floor next to each other. + Read the assembly instructions carefully and assemble the equipment according to the
illustrations. Proceed carefully and cautiously. + First loosen all parts and check for their correct fitting. Then tighten the screws using a tool. + Modifications to the design or improper repairs may pose a hazard to the user and should not be
carried out. The product warranty may be void as a result. + Only authorized service technicians are permitted to carry out all servicing and/or repairs it
excludes maintenance and care. + Damaged or worn components may impair your safety and the lifespan of the equipment.
You should therefore immediately replace damaged or worn components. Please contact your contract partner in such a case. The equipment should no longer be used until it has been repaired. When needed, only use original Taurus spare parts. + Check the tightness of all screw connections once a month. + In order to be able to guarantee the constructively defined safety level of this equipment, we recommend having the equipment regularly maintained (at least once a year) by specialists (service technicians of your contract partner). + The equipment may be cleaned of dust, dirt and sweat using a damp cloth. The use of solvents should be strictly avoided. Also, make sure that no liquids (e. g. sweat) get into the openings of the equipment.
8
84
2.2 Faults and Troubleshooting
The equipment runs through regular quality controls during production. Nevertheless, errors or malfunctions on the equipment may occur. Individual parts are often the cause of faults and replacement is usually sufficient. Please use the following overview to see the most common errors and how to repair them. If the equipment still does not work properly, please contact your contract partner.
Problem
Scraping noises
Weight is suspended in the air
Cause Cable or pulleys not running smoothly or are damaged
Cable is too tightly stretched
Solution
Perform a visual check of the route of the cable or of the pulley or of the pulley guide
Readjust cable tension
Cable is not taut
Cable is too slack
Readjust cable tension
Squeaking & cracking Screws are either too loose or Check that screws are correctly
noises
too tight
tightened or lubricate
2.3 Maintenance and service calendar
The multi-gym needs to be cleaned after every training session with a moist towel (no solvent!) in order to avoid damage caused by sweat.
The following routine work must be done in the specified time intervals:
Part Pulling ropes and rollers Bolts Pulleys and cable guide Legends: C = cleaning; I = inspect
Weekly C / I
I
Weekly I
2x annually Annually
9
3 ASSEMBLY
In order to make the assembly of the equipment easier, we recommend that you do not initially fully tighten the screws and bolts. However, you should make sure that all screws and bolts are firmly tightened after assembly.
Assembly kit
10
84
Accessories:
11
Step 1: Exploded drawing
No. Description
1 ground tube 2 footplate 3 flat washer 4 lock nut 5 hexagon bolt 7 hexagon bolt
Specification Qty.
1
1
12
6
M12
2
M12x100
2
M12x55
2
12
84
Step 1: Assembly
Schritt 1 Assemble the footplate (2) to the ground tube (1), using two hexagon bolts (7), two hexagon bolts (5), six flat washers (3) and two lock nuts (4).
13
Step 2: Exploded drawing
No. Description
8 guide rod 9 flat washer 10 hexagon bolt 11 weight stack 12 pulley frame 13 hexagon bolt 14 arc-shaped washer 15 lock nut 16 rubber cushion 17 weight stack pin 18 selector rod 19 magnetic pin
Specification
10 M10x20
M8x40 8 M8 60x 26x42
10x100
Qty.
2 2 2 19 1 2 4 2 2 1 1 1
14
84
Step 2: Assembly
Note: Each of the plates has a tare weight of 4.5 kg.
Assemble the two guide rods (8) and the two rubber cushions (16) to the ground tube (1) with two hexagon bolts (10) and two flat washers (9). Put the plates of the weight stack (11) on the guide rods (8) one by one. Put the stack pin into the top plate plate of the weight stack (11). Stick the selector rod (18) into the weight stack (11). Assemble the pulley frame (12) to the selector rod (18). Fix two hexagon bolts (13), four arc-shaped washers (14) and two lock nuts (15) to the two guide rods (8).
15
Step 3: Exploded drawing
No. Description
3 flat washer 4 lock nut 9 flat washer 20 upper frame 21 hexagon bolt 23 shield support frame 24 hexagon bolt 25 lock nut 26 upper pulley frame 27 hexagon bolt
Specification
12 M12 10
M12x45
M10x70 M10
M10x60
Qty.
4 2 10 1 2 1 4 4 1 2
16
84
Step 3: Assembly
Assemble the upper pulley frame (16) to the upper frame (20), using two hexagon bolts (27), four flat washers (9) and two lock nuts (25). Assemble the shield support frame (23) to the upper frame (20), using two hexagon bolts (24) and four flat washers (9). Assemble the guide rods (8) to the upper frame (20), using two hexagon bolts (24) and two flat washers (9). Assemblet the upper frame (20) to the ground tube (1), using two hexagon bolts (21), two flat washers (3) and two lock nuts (4).
17
Step 4: Exploded drawing
No. Description
Specification Qty.
3 flat washer
12
8
4 lock nut
M12
4
9 flat washer
10
8
15 lock nut
M8
4
21 hexagon bolt
M12x45
4
29 big bending tube left
1
30 big bending tube right
1
31 decorative washer
8
4
32 hook
4
33 connection tube
2
34 button head socket screw M10x20
8
18
84
Step 4: Assembly
Assemble the right big bending tube (30) to the connection tube (33), using four button head socket screws (34) and four flat washers (9). Assemble the two hooks (32) to the right big bending tube (30), using two lock nuts (15) and two flat washers (31). Assemble the connection tube (33) to the ground tube (1), using two hexagon bolts (21), four washers (3) and two lock nuts (4). Repeat these steps on the other side.
19
Step 5: Exploded drawing
No. Description
3 flat washer 4 lock nut 36 chip up bar 37 hexagon bolt 38 reinforcing plate 39 connection frame 40 hexagon bolt
Specification
12 M12
M12x65 t4.0x50x160
M12x30
Qty.
18 8 1 8 4 1 2
20
84
Step 5: Assembly
Assemble the connection frame (39) to the upper frame (20), using two hexagon bolts (40) and two flat washers (3). Assemble the connection frame (39) to the left and the right big bending tube (30), using four hexagon bolts (37), eight flat washers (3), two reinforcing plates (38) and four lock nuts (4). Assemble the chin up bar (36) to the left and the right big bending tube (30), using four hexagon bolts (37), eight flat washers (3), two reinforcing plates (38) and four lock nuts (4).
21
Step 6: Exploded drawing
No. Description
3 flat washer 34 button head socket screw 40 hexagon bolt 41 butterfly arm left 42 big flat washer 43 butterfly arm right 44 pulley support frame 45 butterfly arm plate
Specification Qty.
12
6
M10x20
2
M12x30
6
1
10
2
1
1
1
22
84
Step 6: Assembly
Assemble the butterfly arm plate (45) to the upper frame (20), using four hexagon bolts (40) and four washers (3). Assemble the pulley support frame (44) to the upper frame (20), using two hexagon bolts (40) and two flat washers (3). Assemble the left and the right butterly arm (41/43) to the butterfly arm plate (45), using two button head socket screws (34) and two big flat washers (42).
23
Step 7: Exploded drawing
No. Description
34 button head socket screw 42 big flat washer 46 pulley frame 47 leg press frame 48 leg press frame small 49 stop collar 50 socket set screw
Specification Qty.
M10x20
1
10
1
2
1
1
2
M8x10
4
24
84
Step 7: Assembly
Assemble the two pulley frames (46) with the two stop collars (49) to the ground tube (1), using four button head socket screws (50). Assemble the leg press frame (47) and the small leg press frame (48) to the upper frame (20), using one button head socket screw (34) and one big flat washer (42).
25
Step 8: Exploded drawing
No. Description
51 wire 52 double pulley frame
Specification Qty.
1 2
26
84
Step 8: Assembly
Devide the cable (51) and guide one of its ends starting from point A though the following points: B, C, D, E, F, G, H, I, J, K and the double pulley frame (52). When you are finished fix the ball head back to the wire.
27
Step 9: Exploded drawing
No. Description
53 wire
Specification Qty.
2
28
84
Step 9: Assembly
Devide the cable (53) and guide one of its ends starting from point A though the following points: B, C, D, E, F, G, H, I, J and K. When you are finished fix the ball head back to the wire.
29
Step 10: Exploded drawing
No. Description
9 flat washer 24 hexagon bolt 25 lock nut 35 connection part 54 shield right 55 button head socket screw 31 flat washer 57 shield left
Specification Qty.
10
4
M10x70
2
M10
2
1
1
M8x16
8
8
8
1
30
84
Step 10: Assembly
Assemble the connection part (35) to the upper frame (20), using two hexagon bolts (24), four flat washers (9) and two lock nuts (25). Assemble the two shields (54/57) to the shield support frame (23), using eight head socket screws (55) and eight flat washers (31).
31
Step 11: Exploded drawing
No. Description
Specification Qty.
6 hexagon bolt
M8x20
8
9 flat washer
10
4
22 back cusion
1
25 lock nut
M10
4
28 seat cushion
10
1
31 flat washer
8
8
58 seat cushion tube
1
59 support tube
1
60 seat cushion adjustment tube 12x128
1
61 live shaft
2
62 back cushion tube
1
32
84
Step 11: Assembly
Put the support tube (59) into the seat cushion adjustment tube (60). Assemble the seat cushion tube (58) and the back cushion tube (62) to the seat cushion adjustment tube (60), using two live shafts (61), four flat washers (9) and four lock nuts (25). Assemble the back cushion (22) and the seat cushion (28) to the seat cushion tube (58) and the back cushion tube (62), using eight hexagon bolts (6) and eight falt washers (31). NOTE: Please make sure that the parts are showing in the correct direction while assembling them. See drawings.
33
Step 12: Exploded drawing
No. Description
Specification
Qty.
34 button head socket screw M10x20
4
63 back cushion support tube
2
64 end cap-50
4
34
84
Step 12: Assembly
Assemble the two back cushion support tubes (63) to the support tube (59), using four end caps (64) and four button head socket screws (34). NOTE: Please check if the parts are showing in the correct direction when you are done assembling them. Apply some silicone on the support tube where the seat is sliding back and forth.
35
Step 13: Exploded drawing
No. Description
3 flat washer 4 lock nut 9 flat washer 24 hexagon bolt 25 lock nut 65 connection rod 66 hexagon bolt 67 shaft 68 front support frame
Specification
12 M12 10 M10x70 M10
M12x75 15.9x76.5
Qty.
2 1 2 1 1 1 1 1 1
36
84
Step 13: Assembly
Assemble the front support frame (68) to the support tube (59), using a hexagon bolt (24), two flat washers (9) and one lock nut (25). Assemble the connection rod (65) to the front support frame (68), using one hexagon bolt (66), two flat washers (3) and one lock nut (25).
37
Step 14: Exploded drawing
No. Description
3
flat washer
4
lock nut
9
flat washer
10 hexagon bolt
66 hexagon bolt
67 shaft
Specification
12 M12
M10x20 M12x75 15.9x76.5
Qty.
2 1 2 2 1 1
38
84
Step 14: Assembly
Assemble the support tube (59) to the upper frame (20), using two hexagon bolts (10), one shaft (67) and two flat washers (3) and assemble the connection rod (65) to the connection part (35), using one hexagon bolt (66), two flat washers (3) and one lock nut (4).
39
4 WARRANTY INFORMATION
Taurus fitness equipment is subject to strict quality controls. However, if a fitness equipment purchased from us does not work perfectly, we take it very seriously and ask you to contact our customer service as indicated. We are happy to help you by phone via our service hotline.
Error descriptions Your fitness equipment is developed for long-term, high-quality training. However, should a problem arise, please first read the operating instructions. For further assistance, please contact your contract partner or call our service hotline. To ensure your problem is solved as quickly as possible, please describe the defect as exactly as possible.
In addition to the statutory warranty, we provide a warranty for every fitness equipment purchased from us according to the following provisions.
Your statutory rights are not affected.
Warrantee The warrantee is the first/original buyer and/or any person who received a newly purchased product as a gift from the original buyer.
Warranty periods The following warranty periods begin on delivery of the fitness equipment.
Model WS5
Use Home use
Full warranty 24 months
Repair costs According to our choice, there will either be a repair, a replacement of individual damaged parts or a complete replacement. Spare parts, that have to be mounted while assembling the equipment, have to be replaced by the warrantee personally and are not a part of repair. After the expiration of the warranty period for repair costs, a pure parts warranty applies, which does not include the repair, installation and delivery costs.
The terms of use are defined as follows:
· Home use: solely for private use in private households up to 3 hours per day · Semi-professional use: up to 6 hours per day (e. g. rehabilitation centers, hotels, clubs, company gyms) · Professional use: more than 6 hours per day (e. g. commercial gyms)
40
84
Warranty service Within the warranty period, equipment which develops faults as a result of material or manufacturing defects, will be repaired or replaced at our discretion. Ownership of equipment or parts of equipment which have been replaced is transferred to us. The warranty period is not extended nor does a new warranty period begin following repair or replacement under the warranty.
Warranty conditions For the warranty to be valid, the following steps must be taken:
Please contact our customer service by email or phone. If the product under warranty has to be sent in for repair, the seller bears costs. After expiry of the warranty, the buyer bears the costs of transport and insurance. If the fault is covered by our warranty, you will receive a new or repaired equipment in return.
Warranty claims are invalid in case of damage resulting from: · misuse or improper handling · environmental influences (moisture, heat, electrical surge, dust, etc.) · failure to follow the current safety measures for the equipment · failure to follow the operating instructions · use of force (e. g. hitting, kicking, falling) · interventions which were not carried out by one of our authorized service centers · unauthorized repair attempts
Proof of purchase and serial number Please make sure that you are able to provide the appropriate receipt when claiming on your warranty. So that we can clearly identify the model of your equipment, and for the purposes of our quality control, you will need to give the serial number of your equipment, when contacting the service team. Where possible please have your serial number and your customer number ready when you call our service hotline. It will help us to deal with your request swiftly. If you have trouble finding the serial number on your fitness equipment, our service team is at your disposal to offer further information.
Service outside the warranty period We are also happy to issue an individual cost estimate if there is a problem with your fitness equipment after the warranty has expired, or in cases which do not fall under the terms of the warranty, e. g. normal wear and tear. Please contact our customer service team to find a quick and cost-effective solution to your problem. In such a case you will be responsible for the delivery costs.
Communication Many problems can be solved just by speaking to us as your contract partner. We know how important it is to you as a user of the fitness equipment to have problems solved quickly and simply, so you can enjoy working out with minimal interruption. For that reason, we also want to resolve your queries quickly and in a straightforward manner. Thus, please always keep your customer number and the serial number of the faulty equipment handy.
41
5 DISPOSAL
At the end of its operational life, this equipment cannot be disposed of in normal household waste. Instead, it must be disposed of via an electricals recycling centre. Further information can be obtained from your local authority`s recycling service. The materials can be recycled as per their symbols. Through the reuse, recycling of materials or other forms of recovery of old equipment, you make an important contribution to the protection of the environment.
6 ORDERING ACCESSORIES
Floor mat set ArtNr. TF-FMS-B
Silicone spray ArtNr. ST-1003
42
84
7 ORDERING SPARE PARTS
7.1 Service hotline
So that we can give you the best possible service, please have your model name, part number, serial number, exploded drawing and parts list ready.
SERVICE HOTLINE
DE
+49 4621 4210-0
+49 4621 4210-699
service@sport-tiedje.de
Mo. - Fr. Sa.
8:00 - 18:00 9:00 - 18:00
DK
80 90 16 50
+49 4621 4210-945
info@t-fitness.dk
Ma. - Fr. Lø.
8:00 - 18:00 9:00 - 18:00
FR
+33 (0) 172 770033
+49 4621 4210-933
service-france@sport-tiedje.fr
Lun. - Ven. 8:00 - 18:00
Sam.
9:00 - 18:00
NL
+31 172 619961
info@fitshop.nl
Ma. - Do. Vr. Za.
9:00 - 17:00 9:00 - 21:00 10:00 - 17:00
UK
INT
+44 141 876 3972
orders@powerhousefitness.co.uk
Mon. - Fri. 9:00 - 17:00
+49 4621 4210-0
service-int@sport-tiedje.de
Mon - Fri 8:00 - 18:00
Sat
9:00 - 18:00
7.2 Serial number and model name
Before assembling your equipment, find the serial number on the white sticker and enter it in the appropriate space.
Serial number:
Brand / category: Taurus / weight station
Model name: WS5
43
7.3 Parts list
No. Description 1 ground tube 2 footplate 3 flat washer 4 lock nut 5 hexagon bolt 6 hexagon bolt 7 hexagon bolt 8 guide rod 9 flat washer 10 hexagon bolt 11 weight stack 12 pulley frame 13 hexagon bolt 14 arc-shaped washer 15 lock nut 16 rubber cushion 17 weight stack pin 18 selector rod 19 magnetic pin 20 upper frame 21 hexagon bolt 22 back cushion 23 shield support frame 24 hexagon bolt 25 lock nut 26 upper pulley frame 27 hexagon bolt 28 set cushion 29 big bending tube left 30 big bending tube right 31 flat washer 32 hook
44
Specification
12 M12 M12x100 M8x20 M12x55 10 M10x20
M8x40 8 M8 60x26x42
10x100 M12x45
M10x70 M10 M10x45 1
8
Qty. 1 1 46 12 2 8 2 2 32 4 19 1 2 4 6 2 1 1 2 1 6 1 1 7 11 1 2 1 1 1 12 4
84
No.
Description
Specification
Qty.
33
connection tube
2
34
button head socket screw
M10x20
15
35
connection part
1
36
chip up bar
1
37
hexagon bolt
M12x65
8
38
reinforcing plate
t4.0x50x160
4
39
connection frame
1
40
hexagon bolt
M12x30
8
41
butterfly arm left
1
42
big flat washer
10
3
43
butterfly arm right
1
44
pulley support frame
1
45
butterfly arm plate
1
46
pulley frame
2
47
leg press frame
1
48
leg press frame small
1
49
stop collar
2
50
socket set screw
M8x10
4
51
wire
1
52
double pulley frame
2
53
wire
2
54
shield right
1
55
button head socket screw
M8x16
8
57
shield left
1
58
seat cushion tube
1
59
support tube
1
60
seat cushion adjustment tube
1
61
axis of rotation
12x128
2
62
back cushion tube
1
63
back cushion support tube
2
64
end cap-50
4
65
connection rod
1
66
hexagon bolt
M12x75
2
66
hexagon bolt
M12x75
2
45
No.
Description
67
shaft
68
front support frame
70
chain
71
long bar
72
ship bar short
73
belt
74
ship bar long
75
triceps rope
Specification
Qty.
15.9x76.5
1
1
4
1
1
2
1
1
46
84
7.4 Exploded drawing
47
CONTACT
Company head office Sport-Tiedje GmbH Flensburger Str. 55 24837 Schleswig Germany
Hotline for Technical Information
DE
+49 4621 4210-0 +49 4621 4210-698 technik@sport-tiedje.de
DK
80 90 16 50 +49 4621 4210-945 info@t-fitness.dk
FR
+33 (0) 172 770033 +49 4621 4210-933 service-france@sport-tiedje.fr
NL
+31 172 619961 info@fitshop.nl
UK
INT
+44 141 876 3986
support@powerhousefitness.co.uk
+49 4621 4210-0 service-int@sport-tiedje.de
www.sport-tiedje.com www.taurus-fitness.de
DISCLAIMER
©2011 TAURUS® is a registered brand of the company Sport-Tiedje GmbH. All rights reserved. Any use of this trademark without the e xplicit written permission of Sport-Tiedje is prohibited.
Product and instructions are subject to change. Technical data can be changed without advance notice.
Please find a detailed overview including address and opening hours for all s pecialist fitness stores of the Sport-Tiedje Group in Germany and abroad on the following website.
www.sport-tiedje.com/en/stores
48
84
Notes
49
Notes
50
84
Notes
51
Weight station WS5
Adobe PDF Library 15.0 Adobe InDesign CC 13.1 (Windows)