JBL PartyBox Club 120 User Manual

Important Safety Instructions

For all products:

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
6. Do not install near heat sources like radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
7. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is for your safety. If the provided plug does not fit your outlet, consult an electrician to replace the obsolete outlet.
8. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
9. Use only attachments/accessories specified by the manufacturer.
10. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
11. Unplug this apparatus during lightning storms or when unused for long periods.
12. To disconnect this apparatus from the mains completely, pull the power cord plug from the receptacle.
13. The power cord plug shall remain readily operable.
14. Do not expose batteries to excessive heat such as sunshine, fire, etc.
15. This apparatus is intended for use with the power adapter and/or charging cable supplied by the manufacturer only.

CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN.

The lightning bolt symbol with an arrowhead inside an equilateral triangle ⚡️ is intended to alert the user to the presence of uninsulated 'dangerous voltage' within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation mark inside an equilateral triangle ❗ is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the product.

WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

Note: FCC and IC Statements for Users (U.S. and Canada Only)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAN ICES-3(B)/NMB-3(B)

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/tv technician for help.

Caution: Changes or modifications not expressly approved by HARMAN could void the user's authority to operate the equipment.

For products transmitting RF energy

FCC AND IC INFORMATION FOR USERS

This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC/IC Radiation Exposure Statement

This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.

Human Exposure to RF Fields (RSS-102)

The computers use integrated low-gain antennas that do not emit RF fields exceeding Health Canada's limits for the general population; consult Safety Code 6, available from the Health Canada website at http://www.hc-sc.gc.ca/

For all products except those with wireless operation

HARMAN International hereby declares that this equipment is in compliance with Directive EMC 2014/30/EU, Directive LVD 2014/35/EU. The Declaration of Conformity can be consulted in the support section of our website, accessible via www.jbl.com.

For all products with wireless operation

HARMAN International hereby declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The Declaration of Conformity can be consulted in the support section of our website, accessible via www.jbl.com.

EPILEPSY WARNING

Some people may experience epileptic seizures when exposed to flashing lights.

Precautions

Installation Precautions

Always follow the instructions and precautions from the speaker stand manufacturer.

This speaker features a 36 mm socket for mounting on stands or on a subwoofer pole. When using a stand or pole, observe the following:

• Check the stand or pole specification to ensure the apparatus is designed to support the speaker's weight. Observe all manufacturer's regulations.
• Ensure the stand (or subwoofer/pole) is placed on a flat, stable surface and that you fully extend the stand's legs. Position the stand so that its legs do not create a hazard or obstacle.
• Use this floor stand only on a flat, firm surface. When the support (with extended pole) is set up, tighten the screws and secure the locks. After placing the speaker, check if the setup is stable: if tilted (from the base) up to 10 degrees in any direction, the speaker should not fall over. If necessary, reduce the height of the speakers and extend the stand's foot.
• Route cables so that artists, production personnel, and the public do not trip and knock over the speakers.
• Inspect the stand (or pole and associated hardware) before each use and do not use equipment with worn, damaged, or missing parts.
• Do not attempt to place more than one speaker from the PartyBox series on a single stand or pole.
• Always exercise caution in windy conditions when using outdoors. Additional weight (e.g., sandbags) may be needed to ensure extra stability. Do not attach banners or similar to any part of a speaker system. These can act as wind catchers and topple the system.
• Unless you are certain you can handle the speaker's weight, ask for assistance to place the speaker on the stand or pole.

Introduction

Congratulations on your purchase! This manual contains information about the JBL PARTYBOX CLUB 120 speaker. We recommend taking a moment to read this manual. The manual describes the apparatus and provides step-by-step instructions to help you set up and use the apparatus. Make sure you read and understand all safety instructions before putting the product into use.

If you have any questions about this product, its installation, or operation, please contact your dealer or customer service, or visit us at www.jbl.com.

Package Contents

The package includes:

• 1) Main Unit
• 2) Power Cord (Quantity and plug type vary by region)
• 3) Quick Start Guide, Safety Sheet, Warranty Card

Product Overview

Top Panel

Diagram of the top panel showing controls and indicators:

• 1) Sound Effect Panel: Select a special sound effect.
• 2) BASS BOOST: Enhances bass level: Level 1, Level 2, or Off.
• 3) Playback Controls: Play, pause, resume. Rotate right/left to increase/decrease the main volume.
• 4) Power On/Off: Turns the unit on or off.
• 5) LED Ring:
• Press to turn the light effect on or off.
• Press and hold for at least 2 seconds to turn strobe and star light on or off.
• Rotate right/left to cycle through different light patterns.
• 6) Bluetooth Pairing Button: Press to enter Bluetooth pairing mode.
• 7) Multi-Speaker Connection Button: Press this button to make a connection with multiple speakers.
• 8) Handle: For carrying the speaker.
• 9) Mobile Device Docking Station: For placing a mobile device.

Caution: Do not look directly into the light-emitting parts when the speaker lighting is on.

LED Display:

Rear Panel

Diagram of the rear panel showing ports and controls:

• 1) USB: Connect to USB storage device. Charge mobile device.
• 2) AUX IN: Connect an external audio device with a 3.5 mm audio cable (not supplied).
• 3) Microphone/Guitar Input: Connect a microphone or guitar.
• 4) Mic 2/Guitar Switch: Slide switch for Microphone 2/Guitar.
• 5) Mic 2/Guitar Volume Knob: Adjusts the volume for the corresponding microphone (2) or guitar input.
• 6) GAIN 2: Adjusts the gain for the corresponding microphone (2) or guitar input.
• 7) DAISY CHAIN IN/OUT: Link multiple PARTYBOX speakers in series using 3.5 mm audio cables (not supplied).
• 8) GAIN 1: Adjusts the gain for the corresponding microphone (1) input.
• 9) Microphone 1 Volume Knob: Adjusts the volume for the corresponding microphone (1) input.
• 10) Microphone Input: Connect a microphone.
• 11) Battery Compartment: Pull the latch down to open the battery compartment.
• 12) AC Power: Connect to mains power.
• 13) Mounting on a Pole Stand: Instructions for pole mounting.

Placement

Caution:

• Do not sit or lean on the speaker, nor push it sideways to prevent tipping over and potential damage.
• Place the speaker on a flat, stable surface, ensuring the rubber feet face downwards.

Powering On

Caution:

• Use only the supplied power cord.
• Use AC power or the built-in battery as the power source for the speaker.

Diagram showing power connection:

1. Connect to mains power.
2. To use the built-in battery, disconnect the AC power after charging the speaker.
3. Press the ⏻ button to turn on the device.

Tips:

• Fully charge the speaker before first use to optimize the built-in battery's lifespan.
• You can check the battery level by pressing any button on the speaker.
• The speaker will automatically switch to standby mode if the device is not operated for 20 minutes. You can also press the ⏻ button to turn the device on or off.

Using Your PartyBox

Bluetooth Connection

You can use the speaker with your Bluetooth-compatible smartphone or tablet.

Diagram showing Bluetooth connection steps:

1. Press the ? button on the speaker to enter Bluetooth pairing mode.
2. Select "JBL PartyBox Club 120" on your Bluetooth device to connect.
3. Once connected, you can stream audio from your Bluetooth device to this speaker.

Notes:

• This speaker can store up to 8 paired devices in memory. The ninth paired device will replace the first.
• Enter "0000" if a PIN code is requested for connecting to a Bluetooth device.
• Bluetooth operation may be affected by the distance between this device and your Bluetooth device, and the surrounding environment.

To disable the device's Bluetooth function:

• Turn off this speaker, or
• Turn off Bluetooth on your device.

Reconnecting the Bluetooth Device:

• The next time you turn on this speaker, it will attempt to automatically reconnect to the last connected device.
• Alternatively, select "JBL PartyBox Club 120" on your Bluetooth device to make the connection.

USB Connection

Connect a USB storage device with playable audio content to the speaker's USB port (not for EMEA region).

The speaker will automatically switch to the USB source. Audio playback will start automatically.

Tip: The speaker plays audio files on the USB storage device from the root folder down to the last subfolder level in alphabetical order. Up to 8 subfolder levels are supported.

Supported Audio Formats:

Playing Music

Diagram showing playback controls:

• Press ▶️ once to pause or resume playback.
• Press ▶️ twice to skip to the next track.
• Press ▶️ three times to skip to the previous track.
• Rotate the volume knob clockwise or counterclockwise to increase or decrease the main volume.
• Press BASS BOOST to enhance the bass level: Level 1, Level 2, or Off.

Note: Track skipping is not available in AUX mode.

AUX Connection

Diagram showing AUX connection:

1. Connect an external audio device to the speaker using a 3.5 mm audio cable (not supplied). The speaker will automatically switch to the AUX source.
2. Start audio playback on the external device.

Mixing Sound with Microphone and/or Guitar

By using a microphone or electric guitar (not supplied), you can mix sound with an audio source.

Notes:

• Always set the guitar or microphone volume to the minimum level before connecting or disconnecting the guitar or microphone.
• Always disconnect the guitar or microphone when not in use.

Connecting a Microphone

Diagram showing microphone connection:

1. Connect a microphone to the ? or ? input.
2. When connecting a microphone to the ? input, set the slide switch to the indicated position .

Connecting a Guitar

Diagram showing guitar connection:

1. Connect a guitar to the ? input.
2. Set the slide switch to the indicated position .

Mixing Sound

Sing through the microphone or play the guitar.

• To adjust the audio source volume, rotate the volume knob on the top panel left or right.
• Adjust the microphone volume using the - / + volume knob next to the corresponding microphone (?) input on the rear panel. Adjust the guitar volume using the - / + volume knob next to the ? input on the rear panel.
• To adjust the microphone or guitar gain, turn the GAIN 1 or GAIN 2 knob on the rear panel.

Charging Your Mobile Device

Diagram showing mobile device charging via USB:

Replacing the Battery (JBL BATTERY200)

Diagrams showing battery replacement:

1. Pull the latch down to open the battery compartment and remove the old battery.
2. Insert a new battery of the same type (JBL BATTERY200) with the metal contacts facing down, and close the battery cover.

Carrying Your PartyBox

Caution:

• Ensure all cords are disconnected before carrying the speaker.
• Handle the apparatus carefully during transport to prevent personal injury or damage.

Lift the handle and hold it firmly to move the speaker.

Mounting the PartyBox on a Pole Stand

Caution:

• Installation must be performed by qualified personnel and adhere to safe mounting standards.
• The installer is responsible for the correct selection and use of mounting hardware to mount the speaker correctly and safely on the pole.

Diagram showing pole stand mounting:

Advanced Usage

JBL PARTYBOX App

Download and install the JBL PARTYBOX app to utilize all the apparatus's capabilities.

Icons for downloading the app from Google Play and the App Store.

Light Effect

Diagram showing light effect controls:

• Press the ✨ button to turn the light effect on or off.
• Press and hold for at least 2 seconds to turn strobe and star light on or off.
• Rotate the knob right/left to cycle through different light patterns: NEON, LOOP, BOUNCE, TRIM, SWITCH, or FREEZE.

Sound Effect

Diagram showing sound effect selection buttons.

• Press ?, ?, or ? to select a special sound effect.

Connecting Multiple Speakers

You can connect two or more PARTYBOX speakers together for an even greater sound experience.

Diagram showing connection of multiple speakers.

• Press the ? button on both speakers.

To disconnect: Turn off the device or press the ? button on either speaker.

TIP: By default, the speaker connected to your Bluetooth device acts as the primary speaker.

Series Connection

Diagram showing series connection of speakers.

Factory Settings

Press and hold the ▶️ and ? buttons for more than 10 seconds to restore factory settings.

IPX4

Caution:

• Ensure the charging port is always dry before connecting the power supply.
• Always keep the protective covers closed to ensure splash resistance.

The speaker is IPX4 splash-resistant.

Specifications

Troubleshooting

Caution: Never attempt to repair the apparatus yourself. If you encounter problems using this apparatus, check the following points before requesting service.

System

The speaker cannot be powered on.

• Check if the speaker's battery is depleted. Otherwise, use mains power.

Some Buttons Do Not Work

• The apparatus may be in demo mode. In demo mode, all input sources and buttons except for BASS BOOST and the volume and light pattern controls are disabled. Press and hold the ▶️ and ? buttons simultaneously for more than 10 seconds to exit.

Sound

No sound from the speaker.

• Check if the speaker is powered on.
• Check the volume.
• Ensure a sound source is active and not muted.

Bluetooth

A device cannot connect to the speaker.

• Ensure the device's Bluetooth function is enabled.
• The speaker is already connected to another Bluetooth device. Press and hold the ? button on the speaker for more than 10 seconds to disconnect and pair a new device.

Poor audio quality from a connected Bluetooth device

• Bluetooth reception is poor. Place the device closer to the speaker, or remove obstacles between the device and the speaker.

Compliance

The product complies with the European Union's energy legislation.

Bluetooth Connection Mode

The product is intended for streaming music via a Bluetooth connection. A consumer can stream Bluetooth audio to the speaker. When the device is connected via Bluetooth, the Bluetooth connection must remain active at all times to ensure proper operation.

The product enters sleep mode (network standby) after 20 minutes of inactivity. Power consumption in sleep mode is less than 2.0 Watts, and it can be reactivated via a Bluetooth connection.

Bluetooth Disconnection Mode

The product enters standby mode after 20 minutes of inactivity. Power consumption in standby is less than 0.5 Watts.

Trademark

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by HARMAN International Industries, Incorporated is under license. Other trademarks and trade names are those of their respective owners.

Copyright Information

HARMAN International Industries, Incorporated 8500 Balboa Boulevard, Northridge, CA 91329 USA www.jbl.com

© 2025 HARMAN International Industries, Incorporated. All rights reserved.

JBL is a trademark of HARMAN International Industries, Incorporated, registered in the United States and/or other countries. Features, specifications, and design are subject to change without notice.