User Manual for Lincoln Electric models including: LF 56D Wire Feeder, LF 56D, Wire Feeder, Feeder
READ AND UNDERSTAND INSTRUCTIONS: Read and understand this manual before operating this equipment. Arc welding can be hazardous. Failure to follow the ...
File Info : application/pdf, 19 Pages, 1.82MB
DocumentDocumentLF 56D OPERATOR'S MANUAL IM3165 03/2022 REV03 Lincoln Electric Bester Sp. z o.o. ul. Jana III Sobieskiego 19A, 58-260 Bielawa, Poland www.lincolnelectric.eu ENGLISH 12/05 THANK YOU! For choosing the QUALITY of the Lincoln Electric products. Please check packaging and equipment for damage. Claims for material damaged in shipment must be notified immediately to the dealer. For ease of use, please enter your product identification data in the table below. Model Name, Code & Serial Number can be found on the machine rating plate. Model Name: ............................................................................................................................................................... Code & Serial number: .............................................................................. .............................................................................. Date & Where Purchased: .............................................................................. .............................................................................. ENGLISH INDEX Technical Specifications...................................................................................................................................................... 1 Electromagnetic Compatibility (EMC).................................................................................................................................. 2 Safety .................................................................................................................................................................................. 3 Introduction ......................................................................................................................................................................... 5 Installation and Operator Instructions.................................................................................................................................. 5 WEEE ............................................................................................................................................................................... 12 Spare Parts ....................................................................................................................................................................... 12 REACh .............................................................................................................................................................................. 12 Authorized Service Shops Location .................................................................................................................................. 12 Electrical Schematic .......................................................................................................................................................... 12 Accessories....................................................................................................................................................................... 13 Connection configuration................................................................................................................................................... 15 English I English Technical Specifications NAME LF 56D INPUT Input Voltage U1 Input Amperes I1 40Vdc 4Adc RATED OUTPUT Duty Cycle 40°C (based on a 10 min. period) 100% 60% INDEX K14336-1 EMC Class A Output Current 420A 500A Welding Current Range Peak Open Circuit Voltage 5 ÷ 500A 113Vdc peak DIMENSION Weight Height Width Length 17,7 kg 516 mm 302 mm 642 mm WIRE FEED SPEED RANGE / WIRE DIAMETER WFS Range Drive Rolls Drive roll diameter 1.5 ÷ 22 m/min 4 Ø37 Solid Wires 0.8 ÷ 1.6 mm Protection Rating IP23 Aluminum Wires 1.0 ÷ 1.6 mm OTHERS Cored Wires 0.9 ÷ 1.6 mm Maximum Gas Pressure 0,5 MPa (5 bar) Operating Temperature from -10°C to +40°C Storage Temperature from -25°C to 55°C English 1 English Electromagnetic Compatibility (EMC) 01/11 This machine has been designed in accordance with all relevant directives and standards. However, it may still generate electromagnetic disturbances that can affect other systems like telecommunications (telephone, radio, and television) or other safety systems. These disturbances can cause safety problems in the affected systems. Read and understand this section to eliminate or reduce the amount of electromagnetic disturbance generated by this machine. This machine has been designed to operate in an industrial area. To operate in a domestic area it is necessary to observe particular precautions to eliminate possible electromagnetic disturbances. The operator must install and operate this equipment as described in this manual. If any electromagnetic disturbances are detected the operator must put in place corrective actions to eliminate these disturbances, if necessary with assistance from Lincoln Electric. Before installing the machine, the operator must check the work area for any devices that may malfunction because of electromagnetic disturbances. Consider the following. Input and output cables, control cables, and telephone cables that are in or adjacent to the work area and the machine. Radio and/or television transmitters and receivers. Computers or computer controlled equipment. Safety and control equipment for industrial processes. Equipment for calibration and measurement. Personal medical devices like pacemakers and hearing aids. Check the electromagnetic immunity for equipment operating in or near the work area. The operator must be sure that all equipment in the area is compatible. This may require additional protection measures. The dimensions of the work area to consider will depend on the construction of the area and other activities that are taking place. Consider the following guidelines to reduce electromagnetic emissions from the machine. Connect the machine to the input supply according to this manual. If disturbances occur if may be necessary to take additional precautions such as filtering the input supply. The output cables should be as short as possible and positioned together as close as possible to each other. If possible connect the work piece to ground in order to reduce the electromagnetic emissions. The operator must check that connecting the work piece to ground does not cause problems or unsafe operating conditions for personnel and equipment. Shielding of cables in the work area can reduce electromagnetic emissions. This may be necessary for special applications. WARNING EMC classification of this product is class A in accordance with electromagnetic compatibility standard EN 60974-10 which means that the product is designed to be used in an industrial environment only. WARNING The Class A equipment is not intended for use in residential locations where the electrical power is provided by the public low-voltage supply system. There may be potential difficulties in ensuring electromagnetic compatibility in those locations, due to conducted as well as radiated disturbances. English 2 English Safety 01/11 WARNING This equipment have to be used by qualified personnel. Be sure that all installation, operation, maintenance and repair procedures are performed only by qualified person. Read and understand this manual before operating this equipment. Failure to follow the instructions in this manual could cause serious personal injury, loss of life, or equipment damage. Read and understand the following explanations of the warning symbols. Lincoln Electric is not responsible for damages caused by improper installation, improper care or abnormal operation. WARNING: This symbol indicates that instructions must be followed to avoid serious personal injury, loss of life, or equipment damage. Protect yourself and others from possible serious injury or death. READ AND UNDERSTAND INSTRUCTIONS: Read and understand this manual before operating this equipment. Arc welding can be hazardous. Failure to follow the instructions in this manual could cause serious personal injury, loss of life, or equipment damage. ELECTRIC SHOCK CAN KILL: Welding equipment generates high voltages. Do not touch the electrode, work clamp, or connected work pieces when this equipment is turned on. Insulate yourself from the electrode, work clamp, and connected work pieces. ELECTRICALLY POWERED EQUIPMENT: Turn off the input power using the disconnect switch at the fuse box before working on this equipment. Ground this equipment in accordance with local electrical regulations. ELECTRICALLY POWERED EQUIPMENT: Regularly inspect the input, electrode, and work clamp cables. If any insulation damage exists replace the cable immediately. Do not place the electrode holder directly on the welding table or any other surface in contact with the work clamp to avoid the risk of accidental arc ignition. ELECTROMAGNETIC FIELD MAY BE DANGEROUS: Electric current flowing through any conductor creates electromagnetic field (EMF). EMF fields may interfere with some pacemakers, and welders having a pacemaker shall consult their physician before operating this equipment. CE COMPLIANCE: This equipment complies with the European Community Directives. ARTIFICIAL OPTICAL RADIATION: According with the requirements in 2006/25/EC Directive and EN 12198 Standard, the equipment is a category 2. It makes mandatory the adoption of Personal Protective Equipment (PPE) having filter with a protection degree up to a maximum of 15, as required by EN169 Standard. FUMES AND GASES CAN BE DANGEROUS: Welding may produce fumes and gases hazardous to health. Avoid breathing these fumes and gases. To avoid these dangers the operator must use enough ventilation or exhaust to keep fumes and gases away from the breathing zone. ARC RAYS CAN BURN: Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing. To protect the skin, use suitable clothing made of durable, fireproof material. Protect other nearby personnel with suitable, non-flammable screening and warn them not to watch the arc nor expose themselves to the arc. English 3 English WELDING SPARKS CAN CAUSE FIRE OR EXPLOSION: Remove fire hazards from the welding area and have a fire extinguisher easily accessible. Welding sparks and hot materials from the welding process can easily go through small cracks and openings to adjacent areas. Do not weld on any tanks, drums, containers, or material until the proper steps have been taken to insure that no flammable or toxic vapors will be present. Never use this equipment when flammable gases, vapors or flammable liquids are present. WELDED MATERIALS CAN BURN: Welding generates a large amount of heat. Hot surfaces and materials in work area can cause serious burns. Use gloves and pliers when touching or moving materials in the work area. CYLINDER MAY EXPLODE IF DAMAGED: Use only certificate, compressed gas cylinders containing the correct shielding gas for the process used and properly operating regulators designed for the gas and pressure used. Always keep cylinders in an upright position securely chained to a fixed support. Do not move or transport gas cylinders with the protection cap removed. Do not allow the electrode, electrode holder, work clamp or any other electrically live part to touch a gas cylinder. Gas cylinders must be located away from areas where they may be subjected to physical damage or the welding process including sparks and heat sources. MOVING PARTS ARE DANGEROUS: There are moving mechanical parts in this machine, which can cause serious injury. Keep your hands, body and clothing away from those parts during machine starting, operating and servicing. SAFETY MARK: This equipment is suitable for supplying power for welding operations carried out in an environment with increased risk of electric shock. The manufacturer reserves the right to make changes and/or improvements in design without upgrade at the same time the operator's manual. English 4 English Introduction LF 56D is digital wire feeder which have been designed to work with Lincoln Electric power sources: POWERTEC® i350S, POWERTEC® i420S, POWERTEC® i500S, SPEEDTEC® 400SP, SPEEDTEC® 500SP, FLEXTEC® 350x, FLEXTEC® 500x. The CAN protocol is used for communication between the power source and the wire feeder. All signals from the power source are displayed on the User Interface located in the wire feeder machine. Set of power source and wire feeder allow welding in listed processes: GMAW (MIG/MAG), FCAW, SMAW (MMA), GTAW, CAG. The complete package contains: Wire feeder. USB memory with operator's manual. Easy Start Recommended equipment, which can be bought by user, was mentioned in the chapter "Accessories". Installation and Operator Instructions Read this entire section before installation or operating the machine. Exploitation conditions This machine can operate in harsh environments. However, it is important to use the following simple preventive measures that will ensure its long life and reliable operation: Do not place or operate this machine on a surface with an incline higher than 15° from horizontal. Do not use this machine for pipe thawing. This machine must be located where there is free circulation of clean air without restrictions for air movement. Do not cover the machine with paper, cloth or rags when switched on. Dirt and dust that can be drawn into the machine should be kept away from the item. This machine has a protection rating of IP23. Keep it dry when possible and do not place it on a wet ground or in puddles. Locate the machine away from a radio controlled machinery. Normal operation may adversely affect the operation of a nearby radio controlled machinery, which may result in injury or equipment damage. Read the section on electromagnetic compatibility in this manual. Do not operate in areas with an ambient temperature greater than 40°C. Duty cycle and Overheating The duty cycle of a welding machine is the percentage of time in a 10 minute cycle at which the welder can operate the machine at rated welding current. Example: 60% duty cycle: Welding for 6 minutes. Break for 4 minutes. Excessive extension of the duty cycle will cause the thermal protection circuit to activate. Minutes or decrease Duty Cycle Input Supply Connection Check the input voltage, phase, and frequency of the power source that will be connected to this wire feeder. The acceptable level of input voltage is indicated in the section ,,Technical Specifications and on the rating plate of the power source. Verify the connection of grounding wires from the power source to the input source. English 5 English Controls and Operational Features 5 4 1 17 2 3 Figure 1 6 7 8 9 10 Figure 2 1. EURO Socket: For connecting a welding gun (for GMAW, FCAW process). 2. Quick Coupling Socket: Coolant outlet (supplies cool coolant to the welding gun). 3. Quick Coupling Socket: Coolant inlet (takes warm coolant from the welding gun). WARNING Maximum coolant pressure is 5 bar. 4. Output Socket for SMAW and CAG welding: For connecting welding cable with an electrode holder. 5. U7 User Interface: See ,,User Interface section. 6. Gas Quick Coupling Socket: For connecting a gas pipe. WARNING The machine allows the use all suitable shielding gases with a maximum pressure of 5 bar. 7. Control Socket: 5 pins socket for connecting a control cable. The CAN protocol is used for communication between the power source and wire feeder. 8. Current Socket: For connecting a welding cable. 9. Quick Coupling Socket: Coolant inlet (supplies cool coolant from cooler to the welding machine). 10. Quick Coupling Socket: Coolant outlet (takes warm coolant from welding machine to cooler). 11. Gas Flow Regulator Plug: Gas Flow Regulator can be purchased separately. See "Accessories" section. 12. Switch: Cold Inch / Gas Purge: This switch allows wire feeding (wire test) and gas flow (gas test) without switching on the output voltage. 13. Transport Holder: For the feeder lifting and transporting using a crane. 14. Wire Spool Holder: For wire spool with maximum 16kg weight. Holder allows mounting plastic, steel and fiber spools on the 51mm spindle. WARNING Be sure that wire spool case has to be completely closed during welding. 15. Spool with Wire: Not supplied as standard. 16. Wire Drive: 4-rolls wire drive. WARNING The side panel and wire spool case have to be completely closed during welding. WARNING Do not use handle to move the machine during operation. English 6 English 11 12 18 13 14 15 User Interface Advanced (U7) 16 Figure 3 17. Remote Control Socket: For connecting a Remote Control (see "Accessories" chapter). 18. USB Port: For connecting the USB memory and software updates. Figure 4 Detailed operation of User Interface U7 can be found in the Advanced (U7) IM3170 user manual. Loading the Wire Spool Spools of wire with a maximum weight of 16 kg can be used without an adapter. Holder allows mounting plastic, steel and fiber spools on the 51mm spindle. It is possible to use other spools after using the appropriate adapter, which can be purchased separately (see "Accessories" chapter). Loading the Electrode Wire Turn the input power OFF. Open the spool wire case. Unscrew the locking nut of the sleeve [14]. Load the spool wire on the sleeve so that the spool turns clockwise when the wire is feed into the wire feeder. Make sure that the spindle brake pin goes into the fitting hole on the spool. Screw in the locking nut of the sleeve. Open the wire drive door. Put on the wire roll with the correct groove corresponding to the wire diameter. Free the end of the wire and cut off the bent end making sure it has no burr. WARNING Sharp end of the wire can hurt. Rotate the wire spool clockwise and thread the end of the wire into the wire feeder as far as the Euro Socket. Adjust force pressure roll of the wire feeder properly. English 7 English Adjustments of Brake Torque of Sleeve To avoid spontaneous unrolling of the welding wire the sleeve is fitted with a brake. Adjustment is carried by rotation of its screw M10, which is placed inside of the sleeve frame after unscrewing the brake locking nut. 19 20 21 Figure 5 19. Locking Nut. 20. Adjusting Screw M10. 21. Pressing Spring. Turning the M10 screw clockwise increases the spring tension and increase the brake torque Turning the M10 screw anticlockwise decreases the spring tension and decrease the brake torque. After finishing of adjustment, you should screw brake locking nut again. Adjusting of Pressure Roll Force The pressure arm controls the amount of force the drive rolls exert on the wire. Pressure force is adjusted by turning the adjustment nut clockwise to increase force, counterclockwise to decrease force. Proper adjustment of pressure arm gives the best welding performance. WARNING If the roll pressure is too weak, the roll will slide on the wire. If the roll pressure is set too heavy the wire may be deformed, which cause feeding problems in the welding. The pressure force should be set properly. For this purpose decrease the pressure force slowly until the wire just begins to slide on the drive roll and then increase the force slightly by turning of the adjustment nut by one turn. Inserting Electrode Wire into Welding Torch Turn the welding machine off. Depending of welding process connect proper welding torch to the euro socket [1]. Rated parameters of the torch and welding machine should be matched. Depends on type of gun must be remove the nozzle from the gun and contact tip or protection cap and contact tip. Turn the welding machine on. Hold the Cold Inch/Gas Purge Switch [12] or use torch trigger until wire appear over threaded end of the gun. When the Cold Inch Switch [12] or torch trigger is released the spool of wire should not unwind. Adjust wire spool brake accordingly. Turn the welding machine off. Install a proper contact tip. Depending on the welding process and the type of the gun, install the nozzle (GMAW process) or protection cap (FCAW process). WARNING Take precaution to keep eyes and hands away from the end of the gun while the wire is being come out of the threaded end. English 8 English Changing Driving Rolls WARNING Turn the input power off before installation or changing drive rolls. Wire Feeders LF 56D is equipped with drive roll V1.0/V1.2 for steel wire. For others wires and sizes it is required to install proper drive rolls kit (see "Accessories" chapter) and follow instruction: Turn the input power OFF. Unlock 4 rolls by turning 4 Quick-Change Carrier Gear [26]. Release the pressure roll levers [27]. Change the drive rolls [25] corresponding to the used wire. WARNING Be sure that the gun liner and contact tip are also sized to match the selected wire size. WARNING For wires with the diameter larger than 1.6mm, the following parts have to be changed: The guide tube of the feeding console [23] and [24]. The guide tube of the Euro Socket [22]. Lock 4 new rolls by turning 4 Quick-Change Carrier Gear [26]. Insert the wire through the guide tube, over the roller and through the guide tube of Euro Socket into liner of gun. The wire can be pushed into the liner manually for a few centimeters, and should feed easily and without any force. Lock the pressure roll levers [27]. 27 24 23 22 26 25 Figure 6 Gas Connection WARNING CYLINDER may explode if damaged. Always fix the gas cylinder securely in an upright position, against a cylinder wall rack or purpose-made cylinder cart. Keep cylinder away from areas where it may be damaged, heated or electrical circuits to prevent possible explosion or fire. Keep cylinder away from welding or other live electrical circuits. Never lift welder with cylinder attached. Never allow welding electrode to touch cylinder. Build up of shielding gas may harm health or kill. Use in a well-ventilated area to avoid gas accumulation. Close the gas cylinder valves thoroughly when not in use to avoid leaks. WARNING Welding machine supports all suitable shielding gases at a maximum pressure of 5,0 bar. WARNING Before use, make sure that the gas cylinder contains gas suitable for the intended purpose. Turn off input power at the welding power source. Install a proper gas flow regulator to the gas cylinder. Connect the gas hose to the regulator using the hose clamp. The other end of the gas hose connect to the gas connector on the power source rear panel or directly to the quick connector located on the rear panel of the wire feeder [6]. More details you will find in power source instruction manual. Connect by dedicated interconnection cable (see ,,Accessories chapter) wire feeder and power source. Turn on input power at the welding power source. Open the gas cylinder valve. Adjust the shielding gas flow of the gas regulator. Check gas flow with Gas Purge Switch [12]. WARNING To weld GMAW process with CO2 shielding gas, CO2 gas heater should be used. English 9 English Transport and Lifting WARNING Falling equipment can cause injury and damage to unit. During transporting and lifting with a crane, adhere to the following rules: For lifting a suitable lifting equipment capacity. Dedicated handle [13] can be used to lifting and transporting using a crane only. This solution enables welding while lifting the feeder. 13 Figure 7 Maintenance WARNING For any repair operations, modifications or maintenances, it is recommended to contact the nearest Technical Service Center or Lincoln Electric. Repairs and modifications performed by unauthorized service or personnel will cause the lost of the manufacturer's warranty Any noticeable damage should be reported immediately and repaired. Routine maintenance (everyday) Check condition of insulation and connections of the work leads and insulation of power lead. If any insulation damage exists replace the lead immediately. Remove the spatters from the welding gun nozzle. Spatters could interfere with the shielding gas flow to the arc. Check the welding gun condition: replace it, if necessary. Check condition and operation of the cooling fan. Keep clean its airflow slots. Periodic maintenance (every 200 working hours but at least once a year) Perform the routine maintenance and, in addition: Keep the machine clean. Using a dry (and low pressure) airflow, remove the dust from the external case and from the cabinet inside. If it is required, clean and tighten all weld terminals. The frequency of the maintenance operations may vary in accordance with the working environment where the machine is placed. WARNING Do not touch electrically live parts. WARNING Before removed case, machine has to be turned off and the power lead has to be disconnected from mains socket. WARNING Mains supply network must be disconnected from the machine before each maintenance and service. After each repair, perform proper tests to ensure safety. English 10 English Customer Assistance Policy The business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equipment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask Lincoln Electric for advice or information about their use of our products. We respond to our customers based on the best information in our possession at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such information or advice. We expressly disclaim any warranty of any kind, including any warranty of fitness for any customer's particular purpose, with respect to such information or advice. As a matter of practical consideration, we also cannot assume any responsibility for updating or correcting any such information or advice once it has been given, nor does the provision of information or advice create, expand or alter any warranty with respect to the sale of our products Lincoln Electric is a responsive manufacturer, but the selection and use of specific products sold by Lincoln Electric is solely within the control of, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric affect the results obtained in applying these types of fabrication methods and service requirements. Subject to Change This information is accurate to the best of our knowledge at the time of printing. Please refer to www.lincolnelectric.com for any updated information. English 11 English WEEE 07/06 Do not dispose of electrical equipment together with normal waste! In observance of European Directive 2012/19/EC on Waste Electrical and Electronic Equipment (WEEE) and its implementation in accordance with national law, electrical equipment that has reached the end of its life must be collected separately and returned to an environmentally compatible recycling facility. As the owner of the equipment, you should get information on approved collection systems from our local representative. By applying this European Directive you will protect the environment and human health! Spare Parts 12/05 Part List reading instructions Do not use this part list for a machine if its code number is not listed. Contact the Lincoln Electric Service Department for any code number not listed. Use the illustration of assembly page and the table below to determine where the part is located for your particular code machine. Use only the parts marked "X" in the column under the heading number called for in the assembly page (# indicate a change in this printing). First, read the Part List reading instructions above, then refer to the "Spare Part" manual supplied with the machine that contains a picture-descriptive part number cross-reference. REACh 11/19 Communication in accordance with Article 33.1 of Regulation (EC) No 1907/2006 REACh. Some parts inside this product contain: Bisphenol A, BPA, EC 201-245-8, CAS 80-05-7 Cadmium, EC 231-152-8, CAS 7440-43-9 Lead, EC 231-100-4, CAS 7439-92-1 Phenol, 4-nonyl-, branched, EC 284-325-5, CAS 84852-15-3 in more than 0,1% w/w in homogeneous material. These substances are included in the Candidate List of Substances of Very High Concern for Authorisation of REACh. Your particular product may contain one or more of the listed substances. Instructions for safe use: use according to Manufacturer instructions, wash hands after use; keep out of reach of children, do not put in mouth, dispose in accordance with local regulations. Authorized Service Shops Location 09/16 The purchaser must contact a Lincoln Authorized Service Facility (LASF) about any defect claimed under Lincoln's warranty period. Contact your local Lincoln Sales Representative for assistance in locating a LASF or go to www.lincolnelectric.com/en-gb/Support/Locator. Electrical Schematic Refer to the "Spare Part" manual supplied with the machine. English 12 English Accessories K14204-1 K14175-1 K10095-1-15M K2909-1 K14091-1 E/H-400A-70-5M K10158-1 K10158 R-1019-125-1/08R W000010136 K14183-1 K14184-1 K14185-1 K14258-1 K14259-1 K4283-1 K4284-1 K3607-2 W10429-36-3M W10429-36-4M W10429-36-5M W10429-505-3M W10429-505-4M W10429-505-5M W000345072-2 W000345073-2 W000345069-2 W000345070-2 W000345075-2 W000345076-2 KP14150-V06/08 KP14150-V08/10 KP14150-V10/12 KP14150-V12/16 KP14150-V16/24 KP14150-V09/11 KP14150-V14/20 KP14150-U06/08A KP14150-U08/10A KP14150-U10/12A KP14150-U12/16A KP14150-U16/24A OPTIONS & ACCESSORIES WIRE FEEDER DRUM QUICK CONNECTOR GAS FLOW METER KIT REMOTE CONTROL 6-PINS, 15M 6-PIN/12-PIN ADAPTER REMOTE MIG LF 45 PWC300-7M (CS/PP) ELECTRODE HOLDER 400A/70MM² - 5M ADAPTER FOR SPOOL TYPE B300 ADAPTER FOR SPOOL TYPE B300 ADAPTER FOR SPOOL S200 FLAIR 600 GOUGING TORCH WITH MOUNTED LEAD 2,5M COMPATIBLE POWER SOURCES POWERTEC® i350S POWERTEC® i420S POWERTEC® i500S SPEEDTEC® 400SP SPEEDTEC® 500SP FLEXTEC® 350x CONSTRUCTION FLEXTEC® 350x STANDARD FLEXTEC® 500x MIG/MAG TORCHES LGS2 360 G-3.0M MIG GUN AIR COOLED LGS2 360 G-4.0M MIG GUN AIR COOLED LGS2 360 G-5.0M MIG GUN AIR COOLED LGS2 505 W-3.0M MIG GUN WATER COOLED LGS2 505 W-4.0M MIG GUN WATER COOLED LGS2 505 W-5.0M MIG GUN WATER COOLED PROMIG MAGNUM PROMIG MAGNUM 370 3M PROMIG MAGNUM 370 4.5M PROMIG MAGNUM 400W 3M PROMIG MAGNUM 400W 4.5M PROMIG MAGNUM 500W 3M PROMIG MAGNUM 500W 4.5M ROLL KIT FOR SOLID WIRES ROLL KIT 0.6/0.8VT FI37 4PCS GREEN/BLUE ROLL KIT 0.8/1.0VT FI37 4PCS BLUE/RED ROLL KIT 1.0/1.2VT FI37 4PCS RED/ORANGE ROLL KIT 1.2/1.6VT FI37 4PCS ORANGE/YELL ROLL KIT 1.6/2.4VT FI37 4PCS YELL/GREY ROLL KIT 0.9/1.1VT FI37 4PCS ROLL KIT 1.4/2.0VT FI37 4PCS ROLL KIT FOR ALUMINIUM WIRES ROLL KIT 0.6/0.8AT FI37 4PCS GREEN/BLUE ROLL KIT 0.8/1.0AT FI37 4PCS BLUE/RED ROLL KIT 1.0/1.2AT FI37 4PCS RED/ORANGE ROLL KIT 1.2/1.6AT FI37 4PCS ORANGE/YELL ROLL KIT 1.6/2.4AT FI37 4PCS YELL/GREY English 13 English KP14150-V12/16R KP14150-V14/20R KP14150-V16/24R KP14150-V09/11R KP14150-V10/12R 0744-000-318R 0744-000-319R D-1829-066-4R D-1829-066-5R K14198-PG K14198-PG-3M K14198-PG-5M K14198-PG-10M K14198-PG-15M K14198-PG-20M K14198-PG-25M K14198-PG-30M K14199-PGW K14199-PGW-3M K14199-PGW-5M K14199-PGW-10M K14199-PGW-15M K14199-PGW-20M K14199-PGW-25M K14199-PGW-30M ROLL KIT FOR CORED WIRES ROLL KIT 1.2/1.6RT FI37 4PCS ORANGE/YELL ROLL KIT 1.4/2.0RT FI37 4PCS ROLL KIT 1.6/2.4RT FI37 4PCS YELL/GREY ROLL KIT 0.9/1.1RT FI37 4PCS ROLL KIT 1.0/1.2RT FI37 4PCS -/ORANGE WIRE GUIDES WIRE GUIDE SET BLUE Ø0.6-1.6 WIRE GUIDE SET RED Ø1.8-2.8 EURO WIRE GUIDE Ø0.6-1.6 EURO WIRE GUIDE Ø1.8-2.8 INTERCONNECION CABLES CABLE PACK 5PIN G 70MM2 1M CABLE PACK 5PIN G 70MM2 3M CABLE PACK 5PIN G 70MM2 5M CABLE PACK 5PIN G 70MM2 10M CABLE PACK 5PIN G 95MM2 15M CABLE PACK 5PIN G 95MM2 20M CABLE PACK 5PIN G 95MM2 25M CABLE PACK 5PIN G 95MM2 30M CABLE PACK 5PIN W 95MM2 1M CABLE PACK 5PIN W 95MM2 3M CABLE PACK 5PIN W 95MM2 5M CABLE PACK 5PIN W 95MM2 10M CABLE PACK 5PIN W 95MM2 15M CABLE PACK 5PIN W 95MM2 20M CABLE PACK 5PIN W 95MM2 25M CABLE PACK 5PIN W 95MM2 30M English 14 English Connection configuration English LF 56D K14336-1 REMOTE MIG LF45PWC300-7M K14091-1 REMOTE CONTROL K10095-1 12 PIN to 6 PIN ADAPTER K2909-1 15 English English LF 52D K14335-1 LF 56D K14336-1 COOLARC 26 K14182-1 16 K14198-PG K14198-PG-XM K14199-PGW K14199-PGW-XM POWERTEC i350S K14183-1 POWERTEC i420S K14184-1 POWERTEC i500S K14185-1 English English LF 52D K14335-1 LF 56D K14336-1 SPEEDTEC 400SP K14258-1 SPEEDTEC 500SP K14259-1 17 K14198-PG K14198-PG-XM K14199-PGW K14199-PGW-XM COOLARC 60 K14297-1 English