Electus Distribution - Home
User Manual for DIGITECH models including: XC-0366, Wireless Weather Station With Outdoor Sensor, XC-0366 Wireless Weather Station With Outdoor Sensor
Wireless Weather Station with Outdoor Sensor | Jaycar US Site
Wireless Weather Station with Outdoor Sensor | Wiiltronics
File Info : application/pdf, 8 Pages, 704.31KB
DocumentDocumentUser Manual Wireless Weather Station With Outdoor Sensor XC-0366 Distributed by: TechBrands by Electus Distribution Pty. Ltd. 320 Victoria Rd, Rydalmere NSW 2116 Australia Ph: 1300 738 555 Int'l: +61 2 8832 3200 Fax: 1300 738 500 www.techbrands.com Specifications: Transmitter Frequency: Transmitter Range: Temperature Range: Console Power: Sensor Power: Console Dimensions: Sensor Dimensions: 433MHz 30m -20°C - 70°C 2 x AA Battery (not included) 2 x AA Battery (not included) 220(W) x 141(H) x 36(D) mm 97(W) x 50(H) x 32(D) mm Important: - The weather forecast will only be ready 12 hours after the batteries are inserted. - The radio communication between the receiver and the transmitter will reach a distance of 30m line of sight. Obstacles in the way, such as buildings, trees and high power voltage lines can interfere with the transmission. - Radio interferences created by computer screens, radios, or TV sets can in some cases cut off the radio communication entirely. Please take this into consideration when choosing standing or mounting locations. - Please keep the transmitter indoors if the outdoor temperature reaches below -20°C. Instructions: - Open the battery compartment on the weather station and insert 2 x AA batteries, taking care to put them in the correct polarity. Close the battery compartment. - Open the battery compartment on the transmitter and insert 2 x AA batteries, taking care to put them in the correct polarity. Close the battery compartment. Note: Ensure to install the batteries into the weather station and transmitter within the same hour to ensure that they synchronize properly. Setting the connection to the outdoor sensors: Once the battery is inserted into the transmitter, by default the transmitter supplied with your weather station will be on Channel 1. Set the channel of the transmitter on the back of the sensor. - Press the `CHANNEL' on the weather station to select a channel (1 to 3). This gives you the option of polling 3 outdoor sensors with each weather station. - Press and hold the `CHANNEL' button for 2 seconds to search for outdoor sensors. Setting Temperature Readings in Fahrenheit or Celsius: To toggle between Fahrenheit or Celsius press the "-" button on the rear of the display unit. Setting the date/time: While setting the unit, if no buttons are pressed within 8 seconds the display will automatically switch back to normal clock mode. - Press and hold the `MODE/SET' button for 2 seconds until the year is flashing on the screen. - Press `UP' or `DOWN' to set the year. - Press `MODE/SET' and the month will be flashing on the screen. - Press `UP' or `DOWN' to set the month. - Press `MODE/SET' and the date will be flashing. - Press `UP' or `DOWN' to set the date. - Press `MODE/SET' to select the weekday. There are 7 languages for the weekday: English, Italian, French, Dutch, Spanish, Danish and German. Press `UP' or `DOWN' to set the language. - Press `MODE/SET' and 12/24 will be flashing on the screen. - Press `UP' or `DOWN' to select 12 or 24 hour mode. - Press `MODE/SET' and the "00" icon will start to flash on the screen to set the time zone. - Press `UP' or `DOWN' to set the time zone, ranging from -12 to +12. - Press `MODE/SET' and the hour will be flashing on the display. - Press `UP or `DOWN' to set the hour. - Press `MODE/SET' and the minute will be flashing on the display. - Press `UP' or `DOWN' to set the minute. - Press `MODE'SET' to lock in the settings. Setting the alarm: While setting the unit, if no buttons are pressed within 8 seconds the display will automatically switch back to normal clock mode. - Press the `ALARM' button to select the alarm you want to set. - Press and hold the `ALARM' button for 2 seconds until A1 appears and the alarm hour is flashing on the display. - Press `UP' or `DOWN' to set the A1 alarm hour. - Press `ALARM' and the alarm minute will be flashing on the display. - Press `UP' or `DOWN' to set the A1 alarm minute. - Press `ALARM' and A2 will appear and the alarm hour will be flashing on the display. - Press `UP' or `DOWN' to set the A2 alarm hour. - Press `ALARM' and the alarm minute will be flashing on the screen. - Press `UP' or `DOWN' to set the A2 alarm minute. - Press `ALARM' to lock in the setting. - To stop the alarm, press `MODE/SET' or `ALARM' - To snooze the alarm, press `SNZ/LIGHT' Note: When activated, the alarms will sound at the pre-set time every day for 2 minutes until de-activated. The alarm is a rising alarm, changing volume 4 times within the 2 minutes. To view the current alarm settings, press `ALARM' to view the first alarm time (A1 will show next to the time). Press `ALARM' again to view the second alarm time (A2 will show next to the time). Press `ALARM' again to revert to the current time or the unit will automatically revert in 8 seconds. Snooze function: - When the alarm comes on, press the `SNZ/LIGHT' to activate the snooze function. When the snooze function is on, the "Zz' symbol will appear on the display. - The alarm will be snoozed by 5 minutes before coming on again. - The snooze function can be interrupted by pressing `MODE/SET' or `ALARM' to deactivate, or repeated up to 7 times by pressing the `SNZ/LIGHT' button. Activating and deactivating the alarm: To activate or deactivate the alarms, press the `DOWN' button: - Press once: Alarm 1 activates - Press twice: Alarm 2 activates - Press three times: Both alarms are activated - Press four times: Both alarms are deactivated Temperature Trend Display: After you insert the batteries, the weather station will measure the current temperature. The trend display will show a neutral temperature course (horizontal arrow). The further course of the trend display is determined as follows: - If after an hour the temperature is more than 1°C higher than the first value measured, then a positive course is displayed (arrow pointing upwards). - If after an hour the temperature is more than 1°C lower than the first value measured, then a negative course is displayed (arrow pointing downwards). - If the temperature does not change within the hour, then a neutral value is displayed (horizontal arrow). Relative Humidity Trend Display: After you insert the batteries, the weather station will measure the current relative humidity. The trend display will show a neutral relative humidity course (horizontal arrow). The further course of the trend display is determined as follows: - If after an hour the relative humidity is more than 5% higher than the first value measured, then a positive course is displayed (arrow pointing upwards). - If after an hour the relative humidity is less than 5% higher than the first value measured, then a negative course is displayed (arrow pointing downwards). - If the relative humidity does not change within the hour, then a neutral value is displayed (horizontal arrow). Maximum/Minimum Temperature and Relative Humidity: - To toggle indoor/outdoor maximum/minimum temperatures and humidity data, press the `MEMORY' button: Once to show the maximum temperature and humidity levels. Twice to show the minimum temperature and humidity levels. Three times to return to the current temperature and humidity levels. - To reset the maximum and minimum temperature and humidity, press and hold down the `MEMORY' button for 2 seconds. This will reset all minimum and maximum data recorded to the current displayed values. Temperature Alert Setting: You can program your weather station to sound an alert whenever the outdoor temperature exceeds the upper or lower pre-set limit. The temperature alert can be set for all remote channels. When setting the alert temperatures, the display will change in increments of 1°C. The low temperature alert setting must be at least 1°C below the high temperature alert setting. - Press and hold the `ALERT' button for 2 seconds until the outdoor temperature is flashing. - Press `CHANNEL' to select the channel on which you would like to set the alert. - Press + or to set your desired high temperature alert level. - Press `ALERT' to confirm your setting and the icon for low temperature limit will be flashing on the display. - Press + or to set your desired low temperature alert. Press `ALERT' to confirm the setting. Note: When the temperature reaches the high or low limit, there will be an audible signal and the outdoor temperature will be flashing on the screen. As long as the temperature exceeds the pre-set limit, the display will continue to flash and the alert will sound every 60 seconds. - To deactivate the temperature alert, press `ALERT'. The icon for high or low alert symbols will stop flashing on the display. Pressure Display Selection: Press + to select either inHg (inches of mercury) or hPa (hectopascals). Note that this reading is based on your local conditions and is not adjusted for sea level. Barometric Pressure History: The bar graph on your weather station displays barometric pressure history for the prior 12 hours. The column to the right shows the current pressure. Moving to the left are the prior time periods, beginning with -1 hour, then -2 hours, -3 hours, -6 hours and -12 hours. Weather Forecast: The weather icon on the LCD display will indicate the predicted weather condition for the next 12 hours. The forecast is based on temperature, humidity and pressure data collected over the previous 12 hours. Barometric pressure data must be accumulated by your weather station for 12 hours before the weather forecast/weather icon function is operational. The station uses five different symbols: Sunny, Partly Cloudy, Cloudy, Rainy & Stormy. Weather Forecast Icon Setting: Press and hold the `HIS' button for 2 seconds until the weather forecasting icon is flashing on the display. Use the + button to modify the 5 icons: Sunny, Partly Cloudy, Cloudy, Rainy & Stormy. Press the `HIS' button again to confirm your setting and to end the setting procedure. Tide, Moon Phase, Sunrise and Sunset Displays: Your weather station will display tide, moon phase and sunrise/sunset times based on your location. City codes are pre-programmed into the unit. Determine the city nearest your location using the list below. - Press and hold `LOC' button for 2 seconds until the city selection is flashing on the display. - Press `UP' or `DOWN' to select the city nearest your location. - Press `LOC' to confirm your selection. Australia Adelaide Brisbane Canberra Darwin Hobart Melbourne Perth Sydney Germany Aachen Berlin Düsseldorf Dresden Erfurt Frankfurt Flensburg Freiburg Hannover Bremen Hamburg Rostock Stralsund Koeln Kiel Kassel Leipzig Muenchen Magdeburg Nuremburg Regensburg Stuttgart Saarbruecken Schwerin Denmark Alborg Arhus Copenhagen Odense Abbreviation ADE BNE CBR DRW HBA MEL PER SYD AAH BER DUS DRS ERF FRA FLF FRE HAJ BRE HAM RLG HST CGN KEL KSL LEJ MUC MDB NUE REG STR SCN SCH AAL AAR CPH ODE New Zealand Auckland Christchurch Wellington Hungary Budapest Debrecen Szeged Abbreviation AKL CHC WLG BUD DEB SZE Italy Ancona Bari Bologna Cagliari Catane(catania) Firenze(FLORENCE) Foggia GenovaGENOA Lecce Messina Milano Napoli Palermo Parma Perugia Rome Torino (TURIN) Trieste Venezia Ventimiglia Verona AOI BRI BLQ CAG CTA FLR FOG GOA LEC MES MIL NAP PMO PMF PEG ROM TRN TRS VCE VEN VRN Ireland Dublin DUB Luxembourg Luxembourg LUX Norway Bergen BGO Spain Alicante Andorra Badajoz Barcelona Bilbao Cadix Cordoba Ibiza La coruna Leon Las Palmas Madrid Malaga Palma de mall orca Salamanca Seville Valencia Zaragossa France Besancon Biarritz Bordeaux Brest Cherbourg Clermont ferrand Lyon Marseille Monaco Metz Nantes Nice Orleans Paris Perpignan Lille Rouen Strasbourg Toulouse Finland Helsinki Tampere Great Britain Aberdeen Belfast Birmingham ALC AND BJZ BCN BIO CDZ COR IBZ LCG LEN LPA MAD AGP PMI SLM SVQ VLC ZAZ BSC BIQ BOD BES CER CFE LYS MRS MCO ETZ NTE NCE ORL PAR PGF LIT URO SXB TLS HEL TMP ABZ BFS BHX Oslo Stavanger Netherlands Amsterdam Arnhem Einhoven Enschede Groningen Den haag Rotterdam Portugal Evora Coimbra faro Leiria Lisbon Porto Poland Gdansk Krakow Poznan Szczecin Warsaw Croatia Split Rijeka Zagreb Sweden Gothenburg Malmo Stockholm Slovakia Bratislava Kosice Slovenia Ljubljana Maribor SERBIA Belgrade Austria Graz Innsbruck Linz Salzburg OSL SVG AMS ARN EIN ENS GRQ HAA RTM AVO COI FAO LEI LIS OPO GND KRK POZ SZZ WAW SPU RJK ZAG GOT MMA STO BRV KSC LJU MBX BEG GRZ INN LNZ SZG Bristol Edinburgh Glasgow London Manchester Plymouth Russia CHELYABINSK IRKUTSK Nizhny Novgorod KHABAROVSK KRASNOJARSK SAMARA KAZAN Moscow Novosibirsk OMSK PERM Saint Petersburg Rostov SARATOV Ekaterinburg UFA Ulan-Ude Vladivostok VOLGOGRAD Voronezh BRS EDI GLA LON MAN PLH CEK IKT GOJ KHV KJA KUF KZN MOW OVB OMS PEE PIE ROS RTW SVX UFA UUD VVO VOG VOZ Vienna Belgium Antwerp Bruges Bruxellex Charleroi Liege Switzerland Basel Bern Chur Geneva Locarno Lucerne St Moritz St Gallen Sion Vaduz Zuerich Czech republic Brno Ostrava Prague VIE ANR BRG BRU CRL LGG EAP BRN CHR GVA LOC LUC MOR SGL SIR VDZ ZRH BRQ OSR PRG NOTE: - When the LCD display becomes dimmer, please replace the batteries. The low battery indicator of the transmitter will be displayed at the right side of the LCD display. - Ensure not to mix old and new batteries. - Please dispose of used batteries in a responsible manner. - Never attempt to open, modify or repair the weather station or the transmitters in any way. - Never get the weather station or the transmitters wet. - When humidity is above 70%, the interface will show a sad face.