Instruction Manual for The Home Depot models including: LL-8838D-52-04, LL-8838D-52-04 Ceiling Fan with Light, LL-8838D-52-04, Ceiling Fan with Light, Fan with Light, with Light
Pairing: Add device → Follow the APP operation to turn off the wall switch, and turn it on after 5 seconds. The device will automatically connect to the ...
10 часов назад — Step 1. Take off the set screws from Fan Motor Assembly. Step 2. Secure the Light Kit Mounting Plate onto the Fan Motor Assembly with screws taken off.
Thank you for choosing and using our product. INSTALLATION MANUAL CEILING FAN WITH LIGHT Model No.: LL-8838D-52-04 Fan lamp controller J Short Downrod ×1 K Remot e Cont rol and Holder ×1 L Light Kit Mount ing Plat e ×1 M LED Light Kit ×1 N Light Shade ×1 A Receiver ×1 B Canopy ×1 C Long Downrod Assembly ×1 D Canopy Ring ×1 E Coupling Cover ×1 F Fan Mot or Assembly ×1 G Blade Arm A ×5 H Fan Blade ×5 I Blade Arm B ×5 INSTALLATION KIT 3 15 Fan Blade Screw 10 Fan Blade Arm Screw 3 Mount ing Bracket Outlet Box Screw With Washer Clevis Pin& " R" Pin Magnet NOTE: 1. Some extra hardware may be included. The quantity listed above is the number required for installation. 2. Parts "GG" have already been installed with Long Downrod Assembly, parts "DD" have been installed with Fan Motor Assembly. They need to be disassembled before installation. mute mode (Long Press) (Short Press) (Long Press) (Short Press) Not e: Install the " Tiny Smart" app from Google Play, Apple App Store, or other app stores by scanning the QR code or searching for the app name. Ensure t hat your phone is connect ed t o the int ernet and Bluetoot h enabled. Pairing: Add device Follow the APP operation to turn off the wall switch, and turn it on after 5 seconds. The device will automat ically connect t o t he Ceiling Fan. Slide t o adjust t he Fan Speed. Slide t o adjust t he Light Color. Turn on/ off t he light . Slide to adjust the Brightness of the Light. Turn on/ off t he fan. Quickly change Light Color " White, Yellow, Natural " Turn off t he fan and light . 1H-8 H for t iming t he fan. Sleeping wind (Not applicable on this fan). Fan forward & Fan reverse. mute mode Nat ural Wind: Simulat e nat ural wind and aut omat ically adjust t he wind speed. 7. Install the Light Kit Mounting Plate Step 1. Take off the set screws from Fan Motor Assembly. Step 2. Secure the Light Kit Mounting Plate onto the Fan Motor Assembly with screws taken off. Fan Mot or Assembly Light Kit Mounting Plate Set Screw 8. Install the Light and Light Shade Step 1. Connect the wire terminal to the interface on the LED Light Kit. Step 2. Rotate the Light Shade clockwise to secure it to the Light Kit Mounting Plate. LED Light Kit Light Shade 1. Installing the Fan Blade and Blade Arm Step 1. Attach fan blade onto the blade arms with Fan Blade Screws (BB) provided. Step 2. Attach the Fan Blade Arm onto the motor with the Fan Blade Arm Screws (DD). Fan Blade Screw (BB) Fan Blade Arm Screw (DD) 2. Assembling the Fan Step 1. Assemble the Canopy and coupling cover, route wires from the fan through the downrod. Step 2. Loosen the set screw from the yoke but do not take off, align the holes at the bottom of the downrod with those in the yoke. Step 3. Carefully insert the clevis pin (GG) through the holes in the yoke and downrod (Be careful not to jam the clevis pin against the wires inside the downrod). Step 4. Insert the "R" pin (GG) into the end of the clevis pin. Step 5. Tighten the set screw on the yoke to secure the downrod. Dow nr od Set Screw Yoke " R" pin Clevis Pin 3. Installing the Mounting Bracket Step 1. Take off the screws from outlet box. Step 2. Secure the mounting bracket (EE) onto the outlet box with screws taken off or Outlet Box Screw With Washer (FF) provided. Mounting Bracket (EE) Outlet Box Screw With Washer (FF) 4. Hanging the Fan Step 1. Lift the downrod into the mounting bracket. Rotate the downrod until the seat tab in the mounting bracket is seated in the groove in the downrod ball. Seat Tab Mounting Bracket Groove Downrod Ball 5. Wiring Step 1. Insert the receiver to the mounting bracket Step 2. Connect the wires from the fixture to the house supply wires with wire nuts (AA) , ground wire (green, green/yellow, or bare copper) to ground wire, neutral wire (white or blue) to neutral wire, and hot wire (black or brown) to the hot wire. Step 3. Wrap the connection with electrical tape. Not e: This fan only needs one set of input wires (black, whit e, and ground wire). Bot h of t he fan and light s will be cont rolled by the remot e cont rol. This fan can only be connect ed t o the ON/ OFF swit ch, not a dimmer switch. 6. Attaching the Canopy Step 1. Slide the canopy up to the ceiling and attach it to the mounting bracket with the set screws provided. Step 2. Slide the coupling cover downward to cover the yoke and fix the canopy ring to the canopy with Magnet (HH). Magnet Set Screw Canopy Ring Coupling CoverAdobe Illustrator 26.0 (Windows) Adobe PDF library 16.03